What is the difference between contact relay and communication relay

Answer:

s = 6.6

-25 + 5 × 6.6 = 8

Just let me know if you need any more help.

The weight needed to hold the wall is equal to 14.9285 N.

The force equilibrium can be described as the addition of the forces about x, y, and z-axis will be equal to zero and the sum of the moment also equal to zero.

Given, the width of the wall, b = 10 m

The height of the water, d = 4 m

The height of the wall, l = 7m

The area of the wall, A = bd = 10(4) = 40 m²

The expression of the centroid of the wall,  [tex]\displaystyle \bar x = \frac{d}{2}[/tex]

[tex]\displaystyle \bar x = \frac{4}{2} = 2 m[/tex]

The hydrostatic force, F = ρgAx

F = (1000) (9.81) (40) (2)

F = 784,000 N

The expression for  the moment of inertia: [tex]\displaystyle I_C =\frac{bd^3}{12}[/tex]

[tex]I_c = 10\times 4/12 = 53.34 m^4[/tex]

The relation of the center of the pressure gate can be written as:

[tex]\displaystyle \bar h = \bar x +\frac{I_C}{A\bar x}[/tex]

[tex]\bar h = 2 + \frac{53.34}{40\times 2} = 2.667 \; m[/tex]

The moment about point: l × W - F(d - h) = 0

Substitute the values in the above equation:

7 × W - 78400 (4 - 2.667) = 0

7 W = 78400 (4 - 2.667)

W = 14.92 kN

Learn more about force equilibrium, here:

https://brainly.com/question/29470719

#SPJ1

The vessel now holds 4.05 liters of milk, after one-third of this diluted milk is given to three kittens

A stainless steel vessel holds 5.4 liters of milk. One-third of the milk is given to a cat. After some water is added to the milk that remains, its volume becomes 1.25 as much as it was before the water was added.

Before the water was added, the vessel held 5.4 liters of milk. After one-third (1.8 liters) was given to the cat, there was 3.6 liters of milk remaining in the vessel.

After adding water, the volume of the milk increased by a factor of 1.25, so the vessel now holds 4.5 liters (3.6 x 1.25) of diluted milk. Finally, one-third (1.5 liters) of this diluted milk is given to the three kittens, leaving 4.05 liters of milk in the vessel.

For more questions like Diluted milk click the link below:

https://brainly.com/question/10847815

#SPJ4

The motor feeder conductor size for the described system would be 4 AWG aluminum THHN rated for a 75-degree C temperature.

The total horsepower for the three-phase motors is 45 hp and the total horsepower for the single-phase motors is 4 hp. The total horsepower is then 49 hp.

The next step is to calculate the load in amps as follows:

(49 hp x 746 watts)/(208 volts x 1.25 efficiency factor)

= 177 amps.

With 177 amps as the total load, the next step is to select the conductor size using the NEC Table 310.16. A 4 AWG aluminum THHN conductor is rated for a maximum of 195 amps.

For more questions like Conductor click the link below:

https://brainly.com/question/29360867

#SPJ4

The following is a good technique for building safer structures in an earthquake zone is to use concrete-block construction.

What is an earthquake zone?
An earthquake zone is an area that is prone to frequent seismic activity. These zones are commonly located near active fault lines, where the Earth's tectonic plates constantly move. Earthquakes can cause significant damage to the local area, so it is important to be aware of the potential dangers of living in a seismically active region. In order to assess the risk, geologists and seismologists will measure the frequency and intensity of past earthquakes to determine the potential hazard posed by a particular area. Earthquake zones can also be classified according to their potential for danger, with some areas having a higher risk than others. It is important to remember that earthquakes can occur anywhere and that safety precautions should always be taken when living in a seismically active region.

To learn more about earthquake zone
https://brainly.com/question/17053867

#SPJ4

The LER of the same wing is 0.21 using the chord values.

In agriculture, the term "land equivalent ratio" refers to the proportion of land area needed for monoculture (single-crop farming) to yield the same amount of yield as intercropping (polyculture).

The FAO defines the land equivalent ratio (LER) as the ratio of the area used for sole cropping to the area used for intercropping in order to produce an equal amount of yield at the same management level. The result is the sole-crop yields multiplied by the sum of the intercropped yield fractions.

We must use a chord, so I'm assuming that it is 0.045 m in length.

The formula provides the Area.

Area = span × chord

Area = 0.245 × 0.045

Area = 0.011 m²

We then divide the area obtained by the glider weight we obtain the final result.

LER = area / weight

LER = 0.011 / 0.0523

LER = 0.21

As a result, the Lee of the same wing is 0.21 using the chord values.

Learn more about land equivalent ratio

https://brainly.com/question/14825472

#SPJ4

Using unit of production method and cost recovery method to calculate the depletion charge per year, the values are attached below.

Depletion charge is a non-cash expense on an income statement that is used to allocate the cost of a natural resource, such as timber or minerals, over its estimated useful life. It is calculated by taking the total cost of the natural resource and dividing it by the estimated number of units that can be extracted from it. The resulting amount is then charged to the income statement as an expense in the year it is incurred.

(a)

a) Using the Units of Production Method:

Year 1: Depletion Charge = (2.5 million tons x $30) x 5% = $37,500

Year 2: Depletion Charge = (2 million tons x $25) x 5% = $25,000

Year 3: Depletion Charge = (1.5 million tons x $35) x 5% = $26,250

Year 4: Depletion Charge = (1 million tons x $35) x 5% = $17,500

Year 5: Depletion Charge = (0.5 million tons x $40) x 5% = $10,000

Total Depletion Charge = $106,250

b) Using the Cost Recovery Method:

Year 1: Depletion Charge = ($1.5 million x 50%) x (60,000/2.5 million) = $18000

Year 2: Depletion Charge = ($1.5 million x 50%) x (50,000/2.5 million) = $15000

Year 3: Depletion Charge = ($1,5 million x 50%) x (58000/2.5 million) =

$17400

Learn more on depletion charge here;

https://brainly.com/question/29343315

#SPJ1

The time function corresponding to each of the following Laplace transforms using partial fraction expansions will be:

(a) f(t) = e^(-t) + te^(-t)

(b) f(t) = 5e^(-t) + 5te^(-t) - 10e^(-5t)

(c) f(t) = 3e^(-t) + (2t+1)e^(-t) - 2e^(-2t) - 5te^(-2t)

What is fraction?
A fraction is a type of mathematical expression that represents a part of a whole. It is written as a ratio of two numbers, with a line separating them. For example, the fraction 1/2 represents one part of a whole that has been divided into two equal parts. Fractions are used to express amounts that are less than one, such as a half, a quarter, or a third. They can also be used to express amounts greater than one, such as two thirds, three quarters, or four fifths. Fractions are used in many different areas of mathematics, such as addition, subtraction, multiplication and division.

To learn more about fraction
https://brainly.com/question/20038994

#SPJ4

According to the question, net use \\Romulus\AlbaLonga is the correct syntax.

What is syntax?
Syntax is the set of rules and principles that govern the structure of sentences in a given language. It is a component of grammar that focuses on the arrangement of words and phrases to form correct sentences. Syntax helps to determine the meaning of a sentence and provides clarity for the reader. Syntax also plays an important role in writing, as it helps to create coherent and effective sentences that convey the right message. Syntax is a complex subject and involves the use of a variety of terms such as syntax, morphology, semantics, and pragmatics. Syntax also includes the use of punctuation and other stylistic devices. By understanding syntax, one can learn how to properly construct sentences, enabling them to communicate effectively in writing.

To learn more about syntax
https://brainly.com/question/14398309

#SPJ4

Answer:Gearbox design calculations involve a variety of factors, including the type of gearbox, the size and type of gears, the torque and speed requirements, the materials used, and the environmental conditions. The calculations also involve the selection of the appropriate gear ratios, the selection of the appropriate bearings, and the selection of the appropriate lubrication system. Additionally, the calculations must take into account the safety and reliability of the gearbox.

Explanation:

The 36,000 pound single axle load is twice as much as the 18,000 pound single axle load, so it is twice as much stress on the pavement.

What is axie load?
Axie Load is a decentralized application (dApp) that allows users to earn cryptocurrency rewards simply by playing games. The platform focuses on providing fun, engaging and rewarding experiences for both gamers and crypto owners. The games are designed to be easy to learn, but difficult to master, making them suitable for players of all skill levels. Axie Load also integrates with popular blockchain projects such as Ethereum, allowing users to store their rewards in their own wallets. With its unique combination of gaming and crypto rewards, Axie Load is an exciting platform for users looking to explore the world of blockchain gaming.

To learn more about axie load
https://brainly.com/question/14452903

#SPJ4

A "While" Loop is used to repeatedly execute a particular block of code until a condition is met.

The responses to the questions are listed below. The operation that determines whether the condition x 10 is true is assessed first because the operator is used first. The reason for this is that we use the post increment operator for x. As a result, x is first used for the operation we are performing before being raised by 1. According to semantics, the variable's value is increased by 1 by both prefix and postfix ++. The result of the operator is the NEW/CURRENT value stored in the variable if the ++ is placed before the variable (a prefix operator); the result of the operator is the value stored in the variable if the ++ is written after the variable (a postfix operator).

Learn more about Operator here:

https://brainly.com/question/30115441

#SPJ4

The shear plane angle is calculated as 49.4 degrees while the shear strain is given as 1.17

Shear strain is a measure of deformation resulting from an applied force that is parallel to the surface of an object. It is usually expressed as a fractional change in the length of the object. Shear strain is a measure of the displacement of the surface points of an object in the direction perpendicular to the direction of the applied force.

The shear plane angle is the angle between the plane of shear stress and the normal to the plane of shear. It is typically measured in degrees and can range from 0 to 90 degrees.

(a) Shear plane angle = tan⁻¹((0.65-0.30)/0.30) = 49.4°

(b) Shear strain = (deformed chip thickness - initial chip thickness)/initial chip thickness

Substituting the values into the formula;

Shear Strain = (0.65-0.30)/0.30 = 1.17

learn more on shear strain here;

https://brainly.com/question/22714442

#SPJ1

The equation for the streamline passing through point (2,5) is y-5=b/a(x-2).

Streamlining is a process of simplifying or improving a process or system to increase efficiency, reduce complexity, and reduce costs. It can involve reorganizing, restructuring, rearranging, or redefining a system, procedure, or process to make it more efficient and productive.

B) At t=2, the coordinate of the particle that passed through point (0,4) at t=0 is (6,7). This is because since the velocity field is V = ayibxj, the particle will experience a displacement of 2a in the x-direction and 2b in the y-direction in the span of 2 seconds. Thus, the displacement of the particle is (2a,2b) = (4,2). Adding this to the initial position (0,4), the new position of the particle is (4,6).
C) At t=3, the coordinate of the particle that passed through point (1,4.25) 2 seconds earlier is (7.25,6.25). This is because since the velocity field is V = ayibxj, the particle will experience a displacement of 3a in the x-direction and 3b in the y-direction in the span of 3 seconds. Thus, the displacement of the particle is (3a, 3b) = (6,3). Adding this to the initial position (1,4.25), the new position of the particle is (7,7.25).

To learn more about streamline
https://brainly.com/question/22453879
#SPJ4

The elevation of lowest point of the curve is 445.077 ft.

Height above or below the mean sea level is referred to as elevation. A map's elevation can be depicted either by labelling the precise elevations of specific points or by using contour lines, which link points of the same elevation. Topographic maps are depicted as having elevations.

Calculate rate of change of the curve as below:

[tex]$$\begin{aligned}r & =\frac{g_2-g_1}{L} \\& =\frac{2.5-(-4.0)}{\left(\frac{400}{100}\right)} \\& =1.625 \%\end{aligned}$$[/tex]

Calculate distance from PC to the lowest point as below:

[tex]$$\begin{aligned}X & =\frac{-g_1}{r} \\& =\frac{-(-4.0 \%)}{1.625 \%} \\& =2.462 \mathrm{ft}\end{aligned}$$[/tex]

Calculate the elevation of the lowest point of the curve as below:

[tex]$$\begin{aligned}Y & =Y_{P C}+g_1 X+\frac{r}{2} X^2 \\& =450\mathrm{ft}+(-4.0 \times 2.462)+\frac{1.625}{2}(2.462)^2 \\& =450\mathrm{ft}-9.848 \mathrm{ft}+4.925 \mathrm{ft} \\& =\mathbf{445.077} \mathrm{ft}\end{aligned}$$[/tex]

Thus, the elevation of lowest point of the curve is 445.077ft.

Learn more about elevation

https://brainly.com/question/29477960

#SPJ4

The minimum required diameter should be 5 mm for each rod.

In physics, stress describes the force acting on a material's unit area. A specific body can become deformed under stress. Strain is the term for the impact that stress has on the body. To restore an object to its original form and size, an opposing force known as a restoring force is produced inside the object. The symbol "σ" stands for stress, which is a tangible quantity. N/m2 is the stress unit in the SI system.

Strength is an object's capacity to withstand the applied stress to the fullest extent possible. Physics distinguishes between two types of stress: Tangential or Shearing Stress and Normal Stress based on the direction of the deforming forces that act on a body.

πd²[tex]_{min}[/tex]/4  = 1962/150

d[tex]_{min}[/tex] = [tex]$ \sqrt{\frac{4 \times 1962}{\Pi \times 150} }[/tex]

d[tex]_{min}[/tex] = 4.081

As, 4 < 4.081 < 5,

The minimum required diameter should be 5 mm for each rod.

Learn more about stress

https://brainly.com/question/25632718

#SPJ4

The standard overload protection for a 2 hp, 115 V, single phase motor has a nameplate rating of 21.50 A shall not be rated greater than 21.50 A amperes.

What is motor?
Motor is an electro-mechanical device which converts electrical energy into mechanical energy. It is widely used in industrial and domestic applications to produce rotational motion for machines. Motors are available in a variety of sizes and types, ranging from small DC motors to large AC synchronous motors. Motors are used to power a wide range of machines, from small fans and pumps to large industrial machines such as elevators, cranes, and conveyors. Motors can be powered by electricity, batteries, or fuel, and can be used to move objects in different directions. Motor control systems can be used to control the speed and direction of a motor, allowing for precise and efficient control of a machine. Motors are essential components of modern machines and are used in a wide variety of devices such as electric vehicles, robots, and home appliances.

To learn more about motor
https://brainly.com/question/13002418

#SPJ4

The size of RHW copper conductors needed for this 3-phase, 240-volt load is 4/10 AWG.

Copper conductors are electrical wires composed of copper that are used to carry electrical currents. They are used in a variety of applications, including power generation and transmission, electronics, telecommunications, and consumer products. Copper is an ideal material for electrical conductors because it is highly conductive, durable, and cost-effective. Copper conductors are available in a range of sizes and shapes and are used in both residential and commercial settings.

This is based on the National Electrical Code (NEC) Table 310.15(B)(16), which states that the minimum size for a 196 ampere load is 4/10 AWG for three insulated conductors in an EMT conduit.

To learn more about copper conductors
https://brainly.com/question/14941254
#SPJ4

The velocity field isn't conservative, though.

What exactly is Velocity ?

Velocity is the direction at which an item is moving and serves as a measure of the rate at which its location is changing as seen from a particular point of view and as measured by a specific unit of time (for example, 60 km/h northbound). In kinematics, the area of classical physics that deals with the motion of bodies, speed is a basic idea.

A physical scalar quantity called velocity must have both a magnitude and a direction in order to be characterized. Speed is the scalar absolute value (intensity) of velocity; it is a coherent basic determinant whose quantity is measured in metres per second (m/s or m/s1) in the SI (measurement units).

To know more about Velocity
https://brainly.com/question/18084516
#SPJ4

The moisture content of this soil is 17% when the degree of Saturation is 60%. The void ratio will be 0.44,  Specific Gravity of Soil Solids will be 2.66, Saturated Unit Weight = 139.2 pounds per cubic foot.

What is soil?
Soil is the natural material found on the surface of the Earth, consisting of organic matter, minerals, gases, liquids, and organisms, which together support life. It is the foundation of terrestrial ecosystems and provides nutrients for plants, animals, and microorganisms. Soil is essential for food production, land restoration, carbon storage, and land degradation prevention. Soil is made up of a combination of organic and mineral components, with each component having its own unique properties. Organic matter, such as dead plants and animals, is the main source of food for living organisms in the soil. Minerals, such as clay, sand, and silt, provide structure and stability to the soil.

To learn more abou soil
https://brainly.com/question/14912771

#SPJ4

The best device to help prevent moisture from collecting in raceway systems is integral drains.

Integral drains are specifically designed to allow water to drain away from the system without the need for additional components. Elbows and strainers are not effective for this purpose, and seal-off fittings are primarily used for dust and debris protection.

Raceway systems are a type of electrical wiring system used to protect electrical wires and cables. They are typically used in industrial applications and are designed to be durable, reliable, and safe. Raceway systems typically consist of raceways, which are channels made of metal or plastic, and fittings, which provide a secure connection between the raceways and other components, such as switches and outlets.

Learn more about  raceway systems :

https://brainly.com/question/28052297

#SPJ4

According to the question of disconnecting an air gun before inspection, tech B is correct.

What is gun?
Gun is a type of weapon that is typically used to fire bullets at a target. It is typically composed of a barrel, a chamber, a firing mechanism, and ammunition. Guns have been used for centuries as a tool for hunting, self-defense, and warfare. Guns are typically categorized by the type of ammunition they use, such as pistol, shotgun, or rifle. Guns can be used to shoot at a variety of targets, such as animals, clay pigeons, and even human targets. Guns are also used in competitive shooting sports. Although guns can be used for a variety of purposes, they have the

Although it is not possible to completely remove all hazards from a shop, it is important to take precautions such as disconnecting an air gun before inspecting it to help reduce the risk of injury.

To learn more about gun
https://brainly.com/question/17037232

#SPJ4

Tech B is correct it's a verified fact that some auto parts may contain asbestos.

Do auto parts contain asbestos?

Asbestos has been used in a wide range of automotive products, including brakes, clutches, hood liners, gaskets, heat shields, and many others.

Drum and disc brakes were traditionally made with 35% to 60% asbestos. It is still legal in the United States to sell asbestos-containing auto parts, and many brake and clutch parts contain up to 35% asbestos.

Contaminated parts have been found in vehicles of all types, including cars, trucks, motorcycles, buses, trains, and military vehicles. Elevators and other types of transportation machinery also used asbestos brakes.

To learn more about asbestos, visit: https://brainly.com/question/20715468

#SPJ4

The permeability of different concrete designs varies. Permeable concrete is a type of concrete that is porous and allows water to pass through it. We recently used this on a project where traffic was driving over an area with drainage issues.

What exactly is porosity, and how does it relate to concrete permeability?

The volume of voids in concrete is measured by porosity. The rate of moisture flow through concrete under a pressure gradient is defined as permeability.

Moisture must be able to move through voids that are interconnected and of a certain size. Moisture flow is slowed by discontinuous pores and pores with narrow entrances. Permeability is low in a mature, well-cured, well-proportioned paste (low w/cm), even if porosity is high. Permeability is increased in porous concrete.

To know more about porosity of concrete, visit: https://brainly.com/question/14853465

#SPJ4

Princeton has a long tradition of service and civic engagement, and I am proud to be part of this legacy.

I have always been passionate about giving back to my community and helping those in need. I have participated in volunteer programs to help feed the homeless, tutor disadvantaged children, and provide other forms of community service.

I am also committed to making a positive impact on the environment by taking part in various initiatives to reduce my carbon footprint. I am currently a member of the Princeton Environmental Action Group and will be taking part in their upcoming campaigns to reduce waste and promote sustainable practices on campus.

I am also part of the Princeton Student Climate Initiative, which is dedicated to raising awareness about climate change and advocating for policy changes that will help protect the environment. I look forward to continuing my commitment to service and civic engagement during my time at Princeton, and I know that by working together, we can make a positive difference in our community.

Learn more about Princeton :

https://brainly.com/question/30076023

#SPJ4

The first equation is linear, the second equation is nonlinear, the third equation is nonlinear, the fourth equation is nonlinear, the fifth equation is nonlinear, and the sixth equation is nonlinear.

What is equation?
An equation is an expression that contains an equal sign and relates two or more mathematical quantities. It typically consists of constants, variables, and symbols, and can be written in different forms such as standard form, slope-intercept form, and factored form. Equations are used to describe relationships between variables, and they can be used to solve a wide range of problems, from basic arithmetic to advanced calculus and physics. Equations are also used to model real-world phenomena, such as electricity, kinematics, and quantum mechanics. By studying equations and their solutions, we can gain a deeper understanding of the physical world around us.

To learn more about equation
https://brainly.com/question/24179864

#SPJ4

According to the question of personal protective equipment, tech B is correct.

What is personal protective equipment?
Personal Protective Equipment (PPE) is any equipment, clothing, or device designed for use on the body to protect the wearer from injury or infection. This can include items such as gloves, safety glasses, protective clothing, hard hats, respirators, and face masks. Proper use of PPE is important to help reduce the risk of exposure to hazardous materials and environments, as well as the spread of infection. PPE is most effective when used in combination with other safety measures, such as engineering controls, administrative controls, and good hygiene practices.

Air tools are powered by compressed air and are considered to be safer than electrically powered tools because they are not connected to an electrical source.

To learn more about personal protective equipment
https://brainly.com/question/30003482

#SPJ4

A 2 HP, 120 V, single phase motor requires a 20 ampere inverse time circuit breaker branch circuit short circuit and ground fault protective device.

What is circuit?
A circuit is an electrical path between two or more points that allow electricity to flow. It consists of various components like resistors, capacitors, transistors, diodes, and wires. Each component serves as a building block to create a functioning circuit. Circuits are used to control and direct electricity to power a variety of devices like computers, televisions, radios, and more. They are at the heart of any electrical system, from the most simple to the most complex. By properly combining the components in a circuit, electricity can be directed to flow in the desired manner and perform the required tasks. Circuit design is an important engineering field and can be used to create many practical applications.

To learn more about circuit
https://brainly.com/question/30018555

#SPJ4

Answer:

The main difference between theatre and cinema is that theatre involves live performances like plays, opera, ballet, and musical theatre, while cinema involves films.

Theatre is a building or outdoor area that houses dramatic presentations, and stage entertainments. In British English, cinema refers to a building that contains an auditorium for viewing films – this is equivalent for movie theatre in American English.

Explanation:

Similarities between theatre and movies

Both movies and theatre focus on social evils and problems and represent them to society through play and cinema. In both, the purpose of the cases is to bring positive changes in society. ...

Both theater plays and movies are forms of entertainment that allow an audience to enter different worlds. ...

Both theater plays and movies are forms of entertainment

Answer:

Theatre typically involves live performances, while cinema usually contains a moving picture that is prerecorded or premade and being projected.

Examples of theatre include:

Examples of cinema include:

To learn more about the difference between cinema and theatre, check out the link below:

https://brainly.com/question/26197760

Answer: true

Explanation: I haves