Answer:
joule
Explanation:
heat is express in joules in x Ray equipment
An open-circuit wind tunnel draws in air from the atmosphere through a well-contoured nozzle. In the test section, where the flow is straight and nearly uniform, a static pressure tap is drilled into the tunnel wall. A manometer connected to the tap shows that static pressure within the tunnel is 45 mm of water below atmospheric. Assume that the air is incompressible, and at 25 C, 100 kPa absolute. Calculate the air speed in the wind-tunnel test section
Answer:
Air speed in the wind-tunnel [tex]v_{2}[/tex] = 27.5 m/s
Explanation:
Given data :
Manometer reading ; p1 - p2 = 45 mm of water
Pressure at section ( I ) p1 = 100 kPa ( abs )
temperature ( T1 ) = 25°C
Pw ( density of water ) = 999 kg/m3
g = 9.81 m/s^2
next we apply Bernoulli equation at section 1 and section 2
p1 - p2 = [tex]\frac{PairV^{2} _{2} }{2}[/tex] ---------- ( 1 )
considering ideal gas equation
Pair ( density of air ) = [tex]\frac{P}{RT}[/tex] ------------------- ( 2 )
R ( constant ) = 287 NM/kg.k
T = 25 + 273.15 = 298.15 k
P1 = 100 kN/m^2 = 100 * 10^3 or N/m^2
substitute values into equation ( 2 )
= 100 * 10^3 / (287 * 298.15)
= 1.17 kg/m^3
Also note ; p1 - p2 = PwgΔh ------- ( 3 )
finally calculate the Air speed in the wind-tunnel test section by equating equation ( 1 ) and ( 3 )
[tex]\frac{PairV^{2} _{2} }{2}[/tex] = PwgΔh
[tex]V^{2} _{2}[/tex] = [tex]\frac{2*999* 9.81* 0.045}{1.17}[/tex] = 753.86
[tex]v_{2}[/tex] = 27.5 m/s
Let be a real-valued signal for which when . Amplitude modulation is preformed to produce the signal . A proposed demodulation technique is illustrated below where is the input, is the output and the ideal low-pass filter has a cutoff frequency of and a passband gain of 2. Determine . x(t) X(jω) = 0 g(t) = x(t)sin(2000πt) g(t) y(t) 2000π y(t) EENG 311: Signals and Systems Page 7 of 8 × lowpass filter y(t) cos(2000πt) g
Answer:
hello your question is incomplete attached below is the complete question
answer : attached below
Explanation:
let ; x(t) be a real value signal for x ( jw ) = 0 , |w| > 200[tex]\pi[/tex]
g(t) = x ( t ) sin ( 2000 [tex]\pi t )[/tex]
[tex]x_{1} (t) = \frac{1}{2} x(t) sin ( 4000\pi t )[/tex]
next we apply Fourier transform
attached below is the remaining part of the solution
Which of the following is a disadvantage of using a resistor in place of an inductor in a power-supply filter.
A The output DC voltage will be lower
B. The life of the capacitors will be shorter
C. A resistor will cost much more than an inductor
D. A resistor weighs much more than an inductor
Answer: A. The output DC voltage will be lower
Explanation:
Using a resistor in a power-supply filter instead of an inductor will lead to a lower DC voltage output as resistors reduce voltage.
It would therefore be ideal to use an inductor as it does not lower DC voltage but inductors are expensive and can be quite large which is why it is more common to see resistors used in power-supply filter circuits.
Forcing a solid piece of heated aluminum through a die forms:
A. a stamped part
B.a cast part
C.an extruded part.
D.a forged part
Answer:
B a cast part
Explanation:
Extrusion is defined as the process of shaping material, such as aluminum, by forcing it to flow through a shaped opening in a die. Extruded material emerges as an elongated piece with the same profile as the die opening.
Forcing a solid piece of heated aluminum through a die forms: a cast part. Hence, option B is correct.
What is cast part?A liquid element is more often filled with concrete that has a hollow chamber in the correct form during the casting manufacturing process, and the item is then let to harden.
A casting, which is the term for the solidified component, is ejected or broken out of the mould to complete the procedure.
Thus, option B is correct.
For more details about cast part, click here:
https://brainly.com/question/13653319
#SPJ2
Find R subscript C and R subscript B in the following circuit such that BJT would be in the active region with V subscript C E end subscript equals 5 V and I subscript C equals 25 m A V subscript C C end subscript equals 15 space V comma space V subscript D 0 end subscript equals 0.7 space V comma space beta equals 100 comma space V subscript A equals infinity.. Ignore the early effect in biasing calculations.
Answer: Rc = 400 Ω and Rb = 57.2 kΩ
Explanation:
Given that;
VCE = 5V
VCC = 15 V
iC = 25 mA
β = 100
VD₀ = 0.7 V
taking a look at the image; at loop 1
-VCC + (i × Rc) + VCE = 0
we substitute
-15 + ( 25 × Rc) + 5 = 0
25Rc = 10
Rc = 10 / 25
Rc = 0.4 k
Rc = 0.4 × 1000
Rc = 400 Ω
iC = βib
25mA = 100(ib)
ib = 25 mA / 100
ib = 0.25 mA
ib = 0.25 × 1000
ib = 250 μAmp
Now at Loop 2
-Vcc + (ib×Rb) + VD₀ = 0
-15 (250 × Rb) + 0.7 = 0
250Rb = 15 - 0.7
250Rb = 14.3
Rb = 14.3 / 250
Rb = 0.0572 μ
Rb = 0.0572 × 1000
Rb = 57.2 kΩ
Therefore Rc = 400 Ω and Rb = 57.2 kΩ
Discuss why TVET Institutions need advice of the business community in order
to provide good programmes.
Answer:
Without the indispensable advice of the business community, TVET Institutions will be unable to cover the gap in career knowledge required by the business community. To develop workers who possess the knowledge and skills required by today's business entities, there is always the continual need for the educational institutions (gown) to regularly meet the business community (town). This meeting provides the necessary ground for the institutions to develop programs that groom the workforce with skills that are needed in the current workplace. Educational institutions that do not seek this important advice from the business community risk developing workers with outdated skills.
Explanation:
TVET Institutions mean Technical and Vocational Education and Training Institutions. They play an important role in equipping young people to enter the world of work. They also continue to develop programs that will improve the employability of workers throughout their careers. They regularly respond to the changing labor market needs, adopt new training strategies and technologies, and expand the outreach of their training to current workers while grooming the young people for work.
Poems that focus on one image usually have what purpose? PLEASE HELP MEH!!
A. to make readers understand how one event leads to another
B. to make readers look at something in a new and different way
C. to make a point about how two or three things are alike
Answer:
A. to make readers understand how one event leads to another
Explanation:
Hope this helped have an amazing day!
Poems that focus on one image usually make readers understand how one event leads to another. The correct option is A.
What is poetry?Poetry is literature that uses words chosen and arranged for their meaning, sound, and rhythm to elicit a focused imaginative awareness of experience or a particular emotional response.
Narrative, dramatic, and lyrical poetry are the three basic categories. Sometimes it is difficult to distinguish between them.
For instance, lyrical poems can have narrative sections, just as epic poems can include lyrical passages.
Poetry is a genre of writing that is essential to life, art, and culture. Readers can typically comprehend how one occurrence leads to another in poems that concentrate on a single image.
Thus, the correct option is A.
For more details regarding poetry, visit:
https://brainly.com/question/1852007
#SPJ2