The temperature to which you would have to heat a brass rod for it to be 2.5% longer than it is at 30°C is 218°C (two significant figures).
Explanation: Let's begin with the formula for linear thermal expansion.
ΔL = αLΔT
Here, ΔL is the change in length,α is the coefficient of linear expansion, L is the original length, andΔT is the change in temperature.
The equation can be rearranged as follows:
α = ΔL/LΔT
The coefficient of linear expansion is the change in length per degree Celsius per unit length.
The value of α for brass is given as 1.9 × 10^-5/°C.
So, to solve for the change in temperature required to achieve a 2.5% increase in length,
substitute the values into the formula above:
α = ΔL/L
ΔT1.9 × 10^-5/°C
α= (2.5/100)L/ΔT
The L value can be taken as 1 cm for this problem,
giving:
1.9 × 10^-5/°C = (2.5/100)(1 cm)/ΔT
ΔT = 1 cm/(2.5/100)(1.9 × 10^-5/°C)
ΔT = 218°C (two significant figures).
to know more about thermal expansion visit:
https://brainly.com/question/31608640
#SPJ11
A positive point charge is placed at 5 cm from a negatively charged plate.
it is then pulled away from the plate, so it is 10 cm from the plate. Describe
what happened to the potential energy of the charge. (Hint what
happened to the force on the charge more force means more potential
energy) *
Answer: I'm not sure about this one, but you can go to this link to understand it better https://youtu.be/wEQxtUwiV1E.Its a Khan Academy Video Hope This Helps
Explanation:
Bad codes. Which of these codes cannot be Huffman codes for any probability assignment? (a) {1,01,00}. (b) {00,01,10,110}. (c) (01,10}.
Among the given codes, code (b) {00,01,10,110} cannot be a Huffman code for any probability assignment.
Huffman coding is a prefix coding technique used for data compression, where the more frequent symbols are assigned shorter codes. A Huffman code is uniquely decodable, meaning no code is a prefix of another code. Based on this understanding, we can analyze each of the provided codes to determine if they can be valid Huffman codes.
Code (a) {1,01,00}: This code can be a valid Huffman code. The code lengths are distinct, and no code is a prefix of another code, satisfying the requirements.
Code (b) {00,01,10,110}: This code cannot be a Huffman code. The prefix "10" and "110" overlap, violating the prefix condition. Therefore, it cannot represent a valid Huffman code for any probability assignment.
Code (c) {01,10}: This code can be a valid Huffman code. The code lengths are distinct, and no code is a prefix of another code, meeting the requirements.
In conclusion, out of the given codes, only code (b) {00,01,10,110} cannot be a Huffman code for any probability assignment due to the overlapping prefix condition.
Learn more about Huffman code here:
https://brainly.com/question/31323524
#SPJ11
In which of these can convection not occur
A. Gases
B.solids
C.liquids
D.fluids
I believe the answer would be B.solids.
Explanation:
Hope this helped!
In solids these can convection not occur and convection can occur in both liquids and gases, as they are both considered fluids. Thus, option B is correct.
However, convection cannot occur in solids, as the particles in solids are generally fixed in position and do not have the freedom to move and transfer heat through bulk motion as in convection.
A solid is one of the three fundamental states of matter, along with liquids and gases. It is characterized by having a definite shape and volume. Solids are composed of tightly packed particles, such as atoms, molecules, or ions, that are held together by strong intermolecular forces.
These particles vibrate in fixed positions but do not have the ability to move freely throughout the substance. As a result, solids maintain their shape and volume under normal conditions and exhibit relatively low compressibility compared to gases and liquids. Examples of solids include metals, rocks, wood, plastics, and ice.
Learn more about solid on:
https://brainly.com/question/32439212
#SPJ2
How would you classify an EM wave with a frequency of 10^7 Hz?
Answer:
I think it is television and radio wave
What happened to the kelp forest when the otter was hunted to near extinction?
Answer: Sea otter is the pioneer species in the kelp forest as it regulates and controls the population of other species in the kelp forest.
Explanation:
If sea otters are hunted and their population is brought to extinction then this will cause major harm the ecosystem of the kelp forest and it will disturb the ecological balance in the kelp forest. The herbivorous animals consumed by the sea otters will increase in population and they will consume a lot of vegetation in the forest. The kelp forest which forms the coastline will not remain effective in providing protection against the storms to the neighboring areas.
What happens to the volume of sound as the amplitude gets larger?
On the dot below, which represents the book, draw and label the forces (not components) that act on the book at the lowest point of its circular path. Each force must be represented by a distinct arrow starting on, and pointing away from, the dot. ii. At the lowest point of the circular path, the book is moving only in the horizontal direction. In what direction, if any, is the net vertical force on the book? Up _No Down direction, since the net vertical force is equal to zero Without deriving any equations, briefly explain your reasoning in terms of the book's motion.
At the lowest point of its circular path, the book experiences three distinct forces: the gravitational force (downward), the normal force (upward), and the centripetal force (toward the center of the circular path).
At the lowest point of the circular path, the book is moving only in the horizontal direction. This means that the book has no vertical acceleration since its velocity in the vertical direction remains constant. According to Newton's second law, when there is no vertical acceleration, the net vertical force must be zero.
The gravitational force acts downward, pulling the book toward the center of the Earth. The normal force, exerted by the surface supporting the book, acts upward and balances the gravitational force. These two forces have equal magnitudes and opposite directions, resulting in a net vertical force of zero.
Therefore, at the lowest point of its circular path, the book experiences no net vertical force. The cancellation of the gravitational force and the normal force allows the book to move in a centripetal force circular path with only horizontal motion.
Learn more about centripetal force here
https://brainly.com/question/30624080
#SPJ11
differences between mass and weight
Explanation:
Mass : -
1. It is the amount of mass present in an object.
2. SI unit : Kilograms ( kg )
3. Relation between Mass and Weight is W = mg.
Weight : -
1. It is the force with which it is attracted towards the centre of the earth.
2. SI unit : Newton ( N )
3. Relation between Mass and Weight is W = mg.
Mass is a measure of the amount of matter in an object, while weight is a measure of the force of gravity on the object.
It is much more difficult to move a dresser full of clothes than an empty dresser
Answer:
Newton's Law 2
Hope this helps!
use molecular orbital theory to complete the ground state electron configuration for each of the molecules.
The ground state electron configurations for the molecules are:
Oxygen (O2): σ2s^2 σ*2s^2 σ2p^4 π2p^2
Nitrogen (N2): σ2s^2 σ*2s^2 σ2p^3 π2p^2
To determine the ground state electron configurations of the molecules using molecular orbital theory, we need to consider the molecular orbital diagram and the electron filling order.
Oxygen (O2):
The atomic configuration of oxygen is 1s^2 2s^2 2p^4. In molecular oxygen (O2), we combine the atomic orbitals to form molecular orbitals. The molecular orbital diagram for O2 is as follows:
The filling order for molecular orbitals is as follows: σ2s < σ2s < σ2p < π2p < π2p < σ*2p. According to Hund's rule, each orbital should be singly filled before pairing occurs.
The electron configuration for O2 can be obtained by filling the molecular orbitals with the valence electrons from each oxygen atom:
σ2s^2 σ*2s^2 σ2p^4 π2p^2
Nitrogen (N2):
The atomic configuration of nitrogen is 1s^2 2s^2 2p^3. In molecular nitrogen (N2), we combine the atomic orbitals to form molecular orbitals. The molecular orbital diagram for N2 is as follows:
The filling order for molecular orbitals is the same as in the case of oxygen: σ2s < σ2s < σ2p < π2p < π2p < σ*2p.
The electron configuration for N2 can be obtained by filling the molecular orbitals with the valence electrons from each nitrogen atom:
σ2s^2 σ*2s^2 σ2p^3 π2p^2
Using molecular orbital theory, we determined the ground state electron configurations for the molecules as follows:
Oxygen (O2): σ2s^2 σ*2s^2 σ2p^4 π2p^2
Nitrogen (N2): σ2s^2 σ*2s^2 σ2p^3 π2p^2
Please note that the electron configurations obtained through molecular orbital theory represent the ground state electronic distribution based on the available orbitals and their energy levels.
To learn more about electron, visit
https://brainly.com/question/26084288
#SPJ11
A block of ice at 0∘C is dropped from a height that causes it to completely melt upon impact. Assume that there is no air resistance and that all the energy goes into melting the ice.
What is the height necessary for this to occur. [ Hint: Equate the joules of gravitational potential energy to the product of the mass of ice and its heat of fusion (Lf = 335,000 J/kg).].
A height of about 34,184.49 meters is required for the block of ice to totally melt upon impact.
To determine the height necessary for the block of ice to completely melt upon impact, we need to equate the gravitational potential energy to the energy required to melt the ice.
The gravitational potential energy is given by the formula:
PE = m * g * h
Where PE is the gravitational potential energy, m is the mass of the ice, g is the acceleration due to gravity, and h is the height.
The energy required to melt the ice is the product of the mass of the ice and its heat of fusion (Lf = 335,000 J/kg). Therefore, the energy required to melt the ice is:
E = m * Lf
By equating the gravitational potential energy to the energy required to melt the ice, we have:
m * g * h = m * Lf
The mass of the ice cancels out on both sides, leaving:
g * h = Lf
Now we can solve for the height h:
[tex]\begin{equation}h = \frac{Lf}{g}[/tex]
Substituting the values:
Lf = 335,000 J/kg
g = 9.8 m/s²
h = 335,000 J/kg / 9.8 m/s²
Calculating the height h:
h ≈ 34,184.49 meters
Therefore, the height necessary for the block of ice to completely melt upon impact is approximately 34,184.49 meters.
To know more about the block of ice refer here :
https://brainly.com/question/28213179#
#SPJ11
How many people does it take to change a lightbulb?
the luminous efficacy of a tungsten lamp is about 12 lumens/watt. what is the efficacy of a fluorescent tube (in lumens/watt)? group of answer choices 20 50 80 100
The efficacy of a fluorescent tube, in lumens/watt, is typically in the range of 50 to 100 lumens/watt.
Fluorescent tubes are more efficient than tungsten lamps in converting electrical energy into visible light. They generally have higher luminous efficacy due to their different technology and design. While the specific efficacy can vary depending on the tube's characteristics and design, a range of 50 to 100 lumens/watt is a common estimate for the efficacy of fluorescent tubes. Therefore, among the given options, the closest answer is 50 lumens/watt.
To learn more about fluorescent tube:
https://brainly.com/question/14397769
#SPJ11
The magnetic field of a solenoid is analogous to the electric field of a O charged wire O charged disk O charged parallel-plate capacitor O dipole O battery
The magnetic field of a solenoid is analogous to the electric field of a charged parallel-plate capacitor.
A solenoid is a long coil of wire wound tightly in the form of a cylinder. When an electric current flows through the solenoid, a magnetic field is generated inside it. This magnetic field is similar to the electric field that exists between the plates of a charged parallel-plate capacitor.
In both cases, the field lines are uniformly distributed and run parallel to each other. The strength of the field is proportional to the current for a solenoid and the charge for a capacitor.
Additionally, the magnetic field of a solenoid is similar to the electric field of a capacitor because they both exhibit a directional property, creating a preferred direction for the field lines.
To know more about magnetic field, refer here:
https://brainly.com/question/30331791#
#SPJ11
A positive point charge and a negative point charge are inside a parallel plate capacitor The point charges interact only with capacitor, not with each other. Let the negative capacitor plate be the zero of potential energy for both charges. a. Draw the electric field vector inside the capacitor. b. Draw the forces acting on the two charges. c. Is the potential energy of the positive/negative point charge positive, negative, or zero? Explain. U
d. In which direction does the potential energy of the positive/negative charge decrease? Explain
a. From the positive plate towards the negative plate.
b. The positive point experiences a force directed opposite to the electric field vector, and the negative point experiences in the same direction.
c. The positive point charge is positive, while the negative point charge is zero.
d. The positive charge decreases as it moves towards the negative plate, while the negative charge remains constant.
a. Inside a parallel plate capacitor, the electric field vector is directed from the positive plate toward the negative plate. This field configuration arises due to the accumulation of a positive charge on the positive plate and an equal amount of negative charge on the negative plate.
The electric field vector lines are parallel and uniformly distributed between the plates.
b. The forces acting on the charges can be determined using the equation F = qE, where F is the force, q is the charge, and E is the electric field. The positive point charge will experience a force opposite to the electric field vector since it carries a positive charge.
Therefore, the force on the positive point charge will be directed toward the positive plate. The negative point charge, carrying a negative charge, will experience a force in the same direction as the electric field vector, towards the negative plate.
c. The potential energy (PE) of a point charge in an electric field can be calculated using the equation PE = qV, where q is the charge and V is the electric potential. In this scenario, the potential energy of the positive point charge will be positive.
This is because the positive point charge is moving from a lower potential (negative plate) to a higher potential (positive plate). On the other hand, the potential energy of the negative point charge is zero, as it is chosen as the zero reference point for potential energy.
In summary, inside a parallel plate capacitor, the electric field vector points from the positive plate to the negative plate. The positive point charge experiences a force towards the positive plate, while the negative point charge experiences a force towards the negative plate.
The potential energy of the positive point charge is positive, indicating a higher potential at the positive plate, while the potential energy of the negative point charge is zero, chosen as the reference point.
As the positive point charge moves towards the negative plate, its potential energy decreases, while the potential energy of the negative charge remains constant.
To learn more about charge, visit
https://brainly.com/question/30236242
#SPJ11
Find the change in time (
t) it takes the magnetic field to drop to zero. (A loop of wire of radius 30 mm has electrical resistance 0.038 ohms. The loop is initially inside a uniform magnetic field of magnitude 1.8 T parallel to the loops axis. The magnetic field is then reduced slowly at a constant rate which induces a current 0.20 A in the loop.)
Approximately 6.375 seconds pass before the magnetic field disappears completely.
To find the change in time (Δt) it takes for the magnetic field to drop to zero, we can use Faraday's law of electromagnetic induction.
Faraday's law states that the induced electromotive force (EMF) in a loop of wire is equal to the rate of change of magnetic flux through the loop. Mathematically, it can be expressed as:
[tex]\begin{equation}EMF = -\frac{d\Phi}{dt}[/tex]
Where:
EMF is the electromotive force (voltage)
[tex]\frac{d\Phi}{dt}[/tex] is the rate of change of magnetic flux
In this case, the induced current in the loop is 0.20 A. We can use Ohm's law to relate the current, resistance, and voltage:
EMF = I * R
Where:
I is the current (0.20 A)
R is the resistance (0.038 ohms)
Since the magnetic field is reducing at a constant rate, we can assume that the rate of change of magnetic flux is constant.
The magnetic flux (Φ) through the loop is given by:
Φ = B * A
Where:
B is the magnetic field (1.8 T)
A is the area of the loop (π * r²)
Substituting the values:
Φ = (1.8 T) * (π * (0.03 m)²)
= 0.051 m² * T
Now, we can equate the two equations for EMF:
[tex]\begin{equation}EMF = -\frac{d\Phi}{dt}[/tex]
[tex]\begin{equation}I \cdot R = -\frac{d\Phi}{dt}[/tex]
Rearranging for dt:
[tex]\begin{equation}dt = -\frac{d\Phi}{I \cdot R}[/tex]
Substituting the values:
[tex]\begin{equation}dt = -\frac{0.051\text{ m}^2 \cdot T}{0.20\text{ A} \cdot 0.038\text{ ohms}}[/tex]
[tex]\begin{equation}= -\frac{0.051}{0.008\text{ s}}[/tex]
= -6.375 s
The negative sign indicates that the time is decreasing. However, we are interested in the magnitude of the time, so we can take the absolute value:
Δt = |dt| = 6.375 s
Therefore, the change in time it takes for the magnetic field to drop to zero is approximately 6.375 seconds.
To know more about the EMF refer here :
https://brainly.com/question/22055509#
#SPJ11
Which is a property of every
mixture?
benedict's test shows the presence of choose... . a positive benedict's test appears as choose... . a negative benedict's test appears as
Benedict’s test is a chemical test used to detect the presence of reducing sugars. This test is particularly used to check the presence of glucose in the urine to determine the presence of diabetes. Benedict's test is carried out by adding Benedict's reagent to the test solution and heating the mixture.
Benedict’s reagent is a blue solution made up of sodium citrate, sodium carbonate, and copper sulfate. The reaction results in the reduction of copper ions to copper oxide which is red or yellow in color. The presence of reducing sugars in the sample causes the colour of the solution to change from blue to green, yellow, orange, or red depending on the amount of reducing sugar present. A positive Benedict's test appears as green, yellow, orange, or red, whereas a negative Benedict's test appears as blue. The intensity of the colour varies based on the amount of reducing sugar present. The higher the amount of reduced sugar, the more intense the colour change.
Therefore, a positive Benedict's test shows the presence of reducing sugar while a negative Benedict's test shows the absence of reducing sugar. Benedict's test can be used to distinguish between reducing and non-reducing sugars, which are carbohydrates that are capable of reducing copper ions and those that are not.
Learn more about Benedict’s test here ;
https://brainly.com/question/30663654
#SPJ11
wave is modeled with the function y(x,t)=0.25\cos(0.30x-0.90t+\frac{\pi}{3})y(x,t)=0.25cos(0.30x−0.90t+3 π ) where all lengths are in meters and all times in seconds.
- Find the wavelength of the wave.
- Find the period of the wave
- Find the wave speed (a positive number).
-What is the instantaneous velocity of one of the particles that make up the medium at position 0 at time 22 sec? Make sure to use the correct sign (plus or minus) for your answer.
The wavelength of the wave is 20π/0.30 meters, which simplifies to approximately 209.44 meters.
The period of the wave is 2π/0.90 seconds, which simplifies to approximately 6.98 seconds.
The wave speed is given by the ratio of the wavelength to the period, which is approximately 29.97 meters per second.
To find the instantaneous velocity of a particle at position 0 at time 22 seconds, we differentiate the displacement equation with respect to time and evaluate it at the given time and position.
The derivative of y(x,t) with respect to t is 0.25(0.90)sin(0.30x - 0.90t + π/3). Plugging in x = 0 and t = 22, we find the instantaneous velocity to be approximately 0.177 m/s in the positive direction.
Determine how to find the wavelength of the wave?The given wave equation is y(x,t) = 0.25cos(0.30x - 0.90t + π/3), where x represents the position and t represents the time. The coefficient of x, 0.30, corresponds to the angular wave number (k) of the wave.
The coefficient of t, -0.90, corresponds to the angular frequency (ω) of the wave. By comparing the equation with the general form y(x,t) = Acos(kx - ωt + φ), we can identify the values for k and ω.
Determine how to find the period of the wave?The wavelength (λ) of a wave is given by λ = 2π/k. In this case, k = 0.30, so the wavelength is 2π/0.30, which simplifies to approximately 209.44 meters.
Determine how to find the wave speed?The period (T) of a wave is given by T = 2π/ω. In this case, ω = -0.90, so the period is 2π/(-0.90), which simplifies to approximately 6.98 seconds.
Determine find the instantaneous velocity particles?The wave speed (v) is the ratio of the wavelength to the period, v = λ/T. Substituting the values, we get v = (2π/0.30) / (2π/(-0.90)), which simplifies to approximately 29.97 meters per second.
To find the instantaneous velocity of a particle at position 0 at time 22 seconds, we differentiate the displacement equation with respect to time.
The derivative of cos(0.30x - 0.90t + π/3) with respect to t is -0.90sin(0.30x - 0.90t + π/3).
Plugging in x = 0 and t = 22, we find the instantaneous velocity to be approximately 0.177 m/s in the positive direction.
To know more about displacement, refer here:
https://brainly.com/question/11934397#
#SPJ4
how can isotopes of a given element be identified?
Answer: All isotopes of a given element have the same number of protons but different numbers of neutrons in each atom. ... Each atomic number identifies a specific element, but not the isotope; an atom of a given element may have a wide range in its number of neutrons.
Explanation: Hopefully this helps. Have a great day.
What types of metal solids, (Other then aluminum foil) Would be able to work just like it?
The type of metal solids other then aluminum foil would be able to work is Copper,Tin,Stainless steel,Brass,Nickel and Silver foils.
There are several types of metal solids that can work similarly to aluminum foil in certain applications. Some options include:
1. Copper foil: Copper foil has good electrical conductivity and is often used in electrical and electronic applications, including circuit boards and electromagnetic shielding.
2. Tin foil: Tin foil, also known as tinfoil, is a thin sheet of tin. It is commonly used for wrapping food items and has similar properties to aluminum foil.
3. Stainless steel foil: Stainless steel foil is resistant to corrosion and has high strength. It can be used for various applications, such as heat exchangers, laboratory equipment, and packaging.
4. Brass foil: Brass foil is an alloy of copper and zinc, which provides good electrical and thermal conductivity. It can be utilized in applications similar to copper foil.
5. Nickel foil: Nickel foil has excellent resistance to corrosion and high-temperature environments. It is commonly used in battery manufacturing, aerospace components, and chemical processing.
6. Silver foil: Silver foil is highly conductive and often used in specialized applications where high conductivity is required, such as in certain types of electronic circuits and sensors.
These metal foils may not be as readily available or as widely used as aluminum foil, but they can serve specific purposes depending on their unique properties. It's important to consider factors such as electrical conductivity, thermal conductivity, corrosion resistance, and cost when selecting the appropriate metal foil for a particular application.
For more such questions on metal solids,click on
https://brainly.com/question/16839220
#SPJ8
A student watches as a trash can lid moves across a yard. Which of these could have caused the trash can lid to move?
Answer:
wind energy
Explanation:
Wind energy can be defined as a form of a solar energy. It is generated by the immense force of the wind that blows in an area. Wind energy is a useful energy and is mostly used to generate electricity. It is clean source of energy.
In the context, trash can lid is being blown away by the wind energy and it is seen moving across the yard. The energy of the wind forces the lid of the trash can to move from one place to another against friction. Thus, wind energy caused the trash can lid to move across the yard as seen by a student.
what must you do to maintain steerage on a personal water craft? you must apply the throttle apply the brakes and turn hard drag a foot in the water
To maintain steerage on a personal watercraft, you must apply the throttle, apply the brakes and turn hard, and drag a foot in the water,as you move forward, the watercraft will start moving in the direction you want it to go
Steering a personal watercraft is not as simple as it looks. It can be dangerous and can lead to accidents if the rider does not know how to handle the watercraft. To maintain steerage on a personal watercraft, you must first apply the throttle. As you move forward, the watercraft will start moving in the direction you want it to go. Applying the brakes and turning hard will help you steer the watercraft in the desired direction.
This is achieved by slowing down the watercraft and allowing it to turn naturally in the water. The final step is to drag a foot in the water. This is important when you want to make a sharp turn. Dragging a foot in the water helps to create a pivot point that helps you turn the watercraft in the desired direction, this technique is also used to help you maintain balance on the watercraft. So therefore to maintain steerage on a personal watercraft, you must apply the throttle, apply the brakes and turn hard, and drag a foot in the water,as you move forward, the watercraft will start moving in the direction you want it to go.
To know more about pivot point visit:
https://brainly.com/question/31261482
#SPJ11
What I ferromagnetism??
Answer:
Ferromagnetism is a kind of magnetism that is associated with iron, cobalt, nickel, and some alloys or compounds containing one or more of these elements. It also occurs in gadolinium and a few other rare-earth elements.
Explanation:
Hope this helped Mark BRAINLIEST!!!
A visitor asks, "Why are the orbits of the planets elliptical?"
A) Because both the Sun and the other planets are pulling on each planet, which distorts a circular orbit into an ellipse. B) Because collisions between the planets that took place when the solar system was forming knocked the planets into orbits of this shape. C) This is the only shape that a planet's orbit can have; other types of objects like moons and stars can have orbits with different shapes.
D) This is the only shape an orbit can have that is stable so that the planet doesn't fall into the Sun or go shooting off into space.
The orbits of the planets are elliptical because both the Sun and the other planets are pulling on each planet, which distorts a circular orbit into an ellipse. The correct option is A.
The elliptical shape of the planets' orbits can be explained by gravitational forces acting between celestial bodies. According to Newton's law of universal gravitation, every object with mass exerts an attractive force on other objects. In the case of planets, their orbits are influenced by the gravitational pull of the Sun and the gravitational interactions with other planets in the solar system.
The combined gravitational forces of the Sun and other planets create a net force on each planet, causing its path to deviate from a perfect circle. The resulting gravitational pull distorts the circular orbit into an elliptical shape. This means that the distance between the planet and the Sun varies throughout its orbital path, with the closest point known as perihelion and the farthest point known as aphelion.
While other factors, such as collisions during the formation of the solar system, may have played a role in shaping the planets' orbits, the primary reason for their elliptical shape is the gravitational interaction between celestial bodies. The elliptical orbit is a stable configuration that allows the planet to maintain its trajectory without falling into the Sun or being ejected into space, as mentioned in option D.
To learn more about Planets click here
https://brainly.com/question/7439931
#SPJ11
Two long parallel wires are separated by 9.03 cm and carry currents 1.71 A and 4.67 A. Find the magnitude of the magnetic force that acts on a 3.17-m length of either wire.
The magnitude οf the magnetic fοrce that acts οn a 3.17 m length οf either wire is 0.0405 Newtοns.
What is magnetic fοrce?Magnetic fοrce refers tο the fοrce exerted οn a charged particle οr a current-carrying cοnductοr due tο the presence οf a magnetic field.
F = (μ₀ * I₁ * I₂ * L) / (2π * d)
Given:
I₁ = 1.71 A
I₂ = 4.67 A
L = 3.17 m
d = 9.03 cm = 0.0903 m
After applying the formula to the supplied values, we get:
F = (4π × 10⁻⁷ T·m/A) * (1.71 A) * (4.67 A) * (3.17 m) / (2π * 0.0903 m)
Simplifying the expressiοn:
F ≈ 4π × 10⁻⁷ * 1.71 * 4.67 * 3.17 / 2 * 0.0903
F ≈ 0.0405 N
Therefοre, the magnitude οf the magnetic fοrce that acts οn a 3.17 m length οf either wire is 0.0405 Newtοns.
To learn more about magnetic force,
https://brainly.com/question/30563158
#SPJ4
As an airplane takes off, the air flows across the wings of the airplane. Which of the following would be the best description? I. The air flow across the top of the wing is greater than the air flows across the bottom of the wing. II. The air flow across the top and bottom of the wing is the same. III. The lift force is present because the pressure across the top is less than the pressure across the bottom of the wing.
Answer:
III. The lift force is present because the pressure across the top is less than the pressure across the bottom of the wing.
Explanation:
Here is a list of ways of producing electricity
A ) Wind farms
B ) Coal fired power stations
C ) hydroelectric power stations
D ) nuclear power stations
E ) gas fired power stations
F ) tidal power stations
G) using geothermal energy
(1) State which of these produces clean electricity
(2) State which of these uses fossils fuel
(3) state which of these uses a renewable energy resources
Please help me
Please do not answer from links
Urgent !!!!!!
Will give the brainliest!
* please answer correctly
Answer:
1) A,B,F,G
2)B,D,E
3) A,C,F,G
Explanation:
Think about it: Suppose a meteorite collided head-on with Mars and becomes buried under Mars's surface. What would be the elasticity of this collision? Explain your answer.
a. Elastic collision
b. Inelastic collision
c. Perfectly elastic collision
d. Perfectly inelastic collision
If a meteorite collides head-on with Mars and becomes buried under Mars's surface, the elasticity of this collision would be a d)perfectly inelastic collision.
The elasticity of the collision is a measure of how much energy is lost during the collision. In a perfectly inelastic collision, all of the kinetic energy of the meteorite would be converted to other forms of energy such as heat, sound, and deformation of the planet's surface. This would result in a large crater on the surface of Mars and the meteorite would be buried under the planet's surface.
A perfectly inelastic collision is a collision where two objects stick together after the collision and move as one. During a perfectly inelastic collision, the kinetic energy of the colliding objects is lost due to the deformation of the objects and the generation of heat. The velocity of the objects after the collision is less than the velocity of the objects before the collision.
In conclusion, if a meteorite collides head-on with Mars and becomes buried under Mars's surface, it would be a perfectly inelastic collision because all of the kinetic energy of the meteorite would be lost during the collision. This would result in a large crater on the surface of Mars and the meteorite would be buried under the planet's surface. The correct option is (d).
To know more about meteorites visit:
https://brainly.com/question/1207919
#SPJ11
it took 500 n of force to push a car 4 meters. how much work was done?
Answer:
2000J
Explanation:
The formula for work is W=Force x Distance
W=FxD
W=500N x 4m
W=2,000 Joules