the water depths upstream and downstream of a hydraulic jump is 0.3 m and 1.2 m. Determine flow rate

Answers

Answer 1

This question is incomplete, the complete question is;

the water depths upstream and downstream of a hydraulic jump is 0.3 m and 1.2 m. Determine flow rate  ( in m³ ) if the rectangular channel is 20 m wide.

Answer:

the flow rate is 32.549 m³/sec

Explanation:

Given that

y₁ = 0.3 m

y₂ = 1.2 m

β = 20 m

Now for Rectangular Channel, we know that;

2q²/g = y₁y₂( y₁ + y₂)

where g = 9.81 m/s²

and q = Q/β

so

2(Q/β)²/g = y₁y₂( y₁ + y₂)

we substitute our given values

2(Q/20)²/9.81 = 0.3 × 1.2( 0.3 + 1.2)

2(Q²/400)/9.81 = 0.36(1.5)

2(Q²/400) = 0.54 × 9.81

Q²/400 = 5.2974 / 2

Q²/400 = 2.6587

Q² = 1059.48

Q = √1059.48

Q = 32.549 m³/sec

Therefore the flow rate is 32.549 m³/sec


Related Questions

According to the Bureau of Labor Statistics, which occupation employed 4.2 million people – more than any other occupation – in 2010? Customer Service Representatives Retail Salespersons Cashiers Marketing Specialists

Answers

Answer:

Retail Salespersons

Explanation:

The Bureau of Labor Statistics or the BLS in short is the federal unit or agency of the United States Labor Department. It is the main stats finding agency of the United States federal government in the field of statistics and labor economics.

According to a publication published by the Labor Statistics Bureau, the retail salesperson sector of occupation employed the most people in the U.S. in the year 2010. It provided employment to about 4.2 million people.

Answer:

b. retail salespersons

Explanation:

5.5.1 Dual-edge detector A dual-edge detector is similar to a rising-edge detector except that the output is asserted for one clock cycle when the input changes from 0 to 1 (i.e., rising edge) and 1 to 0 (i.e falling edge). 1. Design a circuit based on the Moore machine and draw the state diagram and ASM chart. 2. Derive the HDL code based on the state diagram of the ASM chart. 3. Derive a testbench and use simulation to verify operation of the code.

Answers

Give an example of a counterargument for an essay on why waffles are better than pancakes.

The resistance of a 1,000-foot length of #6 AWG wire at a temperature of 25 degrees C is  0.4028 ohm. Thus, option B is correct.

What is prototype?

It is a term used in a variety of contexts, including semantics, design, electronics, and software programming.A prototype is an early sample, model, or release of a product built to test a concept or process or to act as a thing to be replicated or learned from.

The statement that defines a prototype is a prototype is a working model of the proposed system. Say for instance a programmer creates a flowchart or an algorithm of an actual program. The flowchart or the algorithm is the prototype of the actual program. This in other words means that prototypes are models of a system. Hence, the statement that defines a prototype.

Therefore, The resistance of a 1,000-foot length of #6 AWG wire at a temperature of 25 degrees C is  0.4028 ohm. Thus, option B is correct.

Learn more about prototype on:

https://brainly.com/question/7509258

#SPJ2

why carbon is not used as a semiconductor material​

Answers

Carbon is not used as semiconductor it has 4 valence electrons in it valence shell but the energy gap is very small it will conduct electricity even at room temperature ,the size of carbon is very small .

sin x +√3 coax= √2

Answers

Answer:

The two values of x are 2n*pi + pi/12 and 2n*pi -5pi/12

Explanation:

The given equation is

Sin x +√3 Cosx= √2

Upon dividing the equation by 2 we get

 [tex]\frac{1}{2}Sinx + \frac{\sqrt{3} }{2}Cosx = \frac{\sqrt{2} }{2}[/tex]

Sin([tex]\frac{pi}{6}[/tex])*Sinx + Cos([tex]\frac{pi}{6}[/tex])*Cosx = [tex]\frac{1}{\sqrt{2} }[/tex]

This makes the formula of

CosACosB + SinASinB = Cos(A-B)

 Cos(x-[tex]\frac{pi}{6}[/tex]) = [tex]\frac{1}{\sqrt{2} }[/tex]

cos(x- pi/6) = cos(pi/4)

upon writing the general equation we get

x-pi/6 = 2n*pi ± pi/4

x = 2n*pi ± pi/4 -pi/6

so we will have two solutions

x = 2n*pi + pi/4 -pi/6

  = 2n*pi + pi/12

and

x = 2n*pi - pi/4 -pi/6

  = 2n*pi -5pi/12

Therefore the two values of x are 2n*pi + pi/12 and 2n*pi -5pi/12.

A blown fuse or tripped circuit breaker shows

Answers

Answer:

Your house is in need of a service upgrade, or it may indicate that your house has too few circuits.

Explanation:

It's a sign that you are making excessive demands on the circuit and need to move some appliances and devices to other circuits.

A _________ is interesting only if the statistics computed from transactions covered by the rule are different than those computed from transactions not covered by the rule.

Answers

Answer: Quantitative association rule.

Explanation:

The quantitative rules of association apply to the basic type of rules of association which exists as X and Y, with X and Y consisting of a collection of numerical and/or categorical attributes. Unlike general association laws, where both the left and right sides of the law should have categorical (nominal or discrete) attributes, a numerical attribute must be included in at least one attribute of the quantitative association rule (left or right).

A brine solution is 26% salt with 70.0 kg of water evaporated per hour. To produce 195 kg of pure salt (0% moisture) per day, how long should the process operate each day and how much brine must be fed to the evaporator per hour?
The process should operate each day for ___ hours.
The amount of brine that must be fed to the evaporator is ___ kg/h.

Answers

Answer:

- the process should operate each day for 7.9286 hours

- the amount of brine that must be fed to the evaporator is 94.594 kg/hr

Explanation:

Given that;

concentration of brine = 26%

so water concentration will be 100% - 26% = 74%

for evaporation of 70kg water per hour, residual is pure salt( 0% moisture)

so mass flow rate of brine = 70/(74%) = 70/0.74 = 94.5945 kg/hr

Amount of pure dry salt produced(0%) = 94.5945 - 70 = 24.5945 kg/hr

Now for production of 195kg of pure dry salt, number of hours required will be

T = 195 / 24.5945 = 7.9286 hrs

Therefore the process should operate each day for 7.9286 hours.

Total brine solution required ( 26% salt conc.) = 195/0.26 = 750 kg

Feed rate of brine solution ( 26% salt conc.) = 750 / 7.9286 = 94.594 kg/hr

Therefore the amount of brine that must be fed to the evaporator is 94.594 kg/hr

Why is the reversed Carnot cycle executed within the saturation dome not a realistic model for refrigeration cycles?

Answers

Explanation:

The paths of warmth and job interactions are inverted by repeating the Carnot process. A Carnot fridge or a Carnot heating system is considered a fridge or heat engine that acts on the reverse Carnot cycle.

The Carnot process comprises liquid phase mixture compression and expanding, which limits mechanical components.

who is the strongest avenger i say hulk but who knows at this point

Answers

Answer:

or is the strongest evenger she hulk

Explanation:

?????????

Answer:

Thor!

Explanation:

In Thor: Ragnarok he beat the Hulk in order for Hulk to win thor had to be electrocuted and in Avengers: Endgame Thor is seen holding open the  "Floodgates" and withstanding the radiation from a dying star, also the fact that Thor is a god means that he is all powerful and the rightful heir to the throne to Asgard, plus the fact that he has defeated Loki multiple times a feat that not even the Hulk has done.

Technician A says that a way to prevent galvanic corrosion is to duplicate the original installation method. Technician B says that a way to prevent galvanic corrosion is to reuse coated bolts. Who is right

Answers

Answer:

Technician A

Explanation:

Galvanic corrosion is not on only one metal alone but caused when two metals are interacting. Thus, Duplicating the original installation method is a better option because re-using a coated bolt doesn't prevent galvanic corrosion because both materials must be coated and not just the bolt and in technician B's case he is coating just the bolt. Thus, technician B's method will not achieve prevention of galvanic corrosion but technician A's method will achieve it.

A work element in a manual assembly task consists of the following MTM-1 elements: (1) R16C, (2) G4A, (3) M10B5, (4) RL1, (5) R14B, (6) G1B, (7) M8C3, (8) P1NSE, and (9) RL1.
(a) Determine the normal times in TMUs for these motion elements.
(b) What is the total time for this work element in sec

Answers

Answer:

a)

1) R16C ; Tn = 17 TMU

2) G4A ; Tn = 7.3 TMU

3) M10B5 ; Tn = 15.1 TMU

4) RL1 ; Tn = 2 TMU

5) R14B ; Tn = 14.4 TMU

6) G1B ; Tn = 3.5 TMU

7) M8C3 ; Tn = 14.7 TMU

8) P1NSE ; Tn = 10.4 TMU

9) RL1 ; Tn = 2 TMU

b) 3.1 secs

Explanation:

a) Determine the normal times in TMUs for these motion elements

1) R16C ; Tn = 17 TMU

2) G4A ; Tn = 7.3 TMU

3) M10B5 ; Tn = 15.1 TMU

4) RL1 ; Tn = 2 TMU

5) R14B ; Tn = 14.4 TMU

6) G1B ; Tn = 3.5 TMU

7) M8C3 ; Tn = 14.7 TMU

8) P1NSE ; Tn = 10.4 TMU

9) RL1 ; Tn = 2 TMU

b ) Determine the total time for this work element in seconds

first we have to determine the total TMU = ∑ TMU = 86.4 TMU

note ; 1 TMU = 0.036 seconds

hence the total time for the work in seconds = 86.4 * 0.036 = 3.1 seconds

If the roller at A and the pin at B can support a load upto 4kN and 8kN, repsectively, determine the maximum intensity of the distributed load w, measured in kN/m, so that failure of the supports does not occur.

Answers

Solution :

Taken moment about point B;

[tex]$\sum M_B = 0$[/tex]

[tex]$\left[(w)(4)(2)-N_A \sin 30^\circ (3)(\sin 30^\circ)-N_A \cos 30^\circ(3 \cos 30^\circ +4) \right] =0$[/tex]

[tex]$N_A = 1.2376w$[/tex]

[tex]$\sum F_x = 0$[/tex]

[tex]$N_A \sin 30^\circ - B_x = 0$[/tex]

[tex]$B_x = 1.2376w \times \sin 30^\circ$[/tex]

[tex]$B_x = 0.6188w$[/tex]

[tex]$\sum F_y = 0$[/tex]

[tex]$B_y+N_A \cos^\circ - (w \times 4) = 0$[/tex]

[tex]$B_y+(1.2376w) \cos 30^\circ - (w \times 4)=0 $[/tex]

[tex]$B_y = 2.9282w$[/tex]

Now calculating the resultant force at B,

[tex]$F_B= \sqrt{B_x^2+B_y^2}$[/tex]

[tex]$F_B= \sqrt{(0.6188w)^2+(2.9282w)^2}$[/tex]

     = 2.9929w

For no failure,

[tex]$N_A<4 \ kN $[/tex]

2.9929 w < 4 kN

[tex]$w < 3.232 \ kN/m$[/tex]

And,

[tex]$F_B < 8 \ kN$[/tex]

2.9929 w < 8 kN

w < 2.673 kN/m

For the safe operation, w = 2.673 kN/m  

What is the primary reason that heating, ventilating, and air conditioning (HVAC) is critical to a data center

Answers

Answer:

It prevents hardware from overheating.

Explanation:

HVAC stands for Heating, ventilation and air conditioning. It may be defined as technology which provides both vehicular as well as indoor environmental comfort. It provides thermal comfort and also used in places where overheating of the equipment or object is not desired.

A data center is a dedicated space which is used to store computer systems and the associated components like telecommunication as well as storage system.

Now proper HVAC system is necessary in data center so as to ensure that the components or the computer system does not get over heated and gets damaged. Overheating of the storage system may lead to loss of valuable information and other important data.

A garden hose fills a 2-gallon bucket in 5 seconds. The number of gallons, g (y), is proportional to the number of seconds, t (x), that the water is running. What is the constant of proportionality?

Answers

Answer:

0.4 gallons per second

Explanation:

A function shows the relationship between an independent variable and a dependent variable.

The independent variable (x values) are input variables i.e. they don't depend on other variables while the dependent variable (y values) are output variables i.e. they depend on other variables.

The rate of change or slope or constant of proportionality is the ratio of the dependent variable (y value) to the independent variable (x value).

Given that the garden hose fills a 2-gallon bucket in 5 seconds. The dependent variable = g = number of gallons, the independent variable = t = number of seconds.

Constant of proportionality = g / t = 2 / 5 = 0.4 gallons per second

Which metal has the ability to rust

A gold

B silver

C iron

D aluminum

Answers

Answer:

I got iron

Explanation:

on my plato test

It’s iron :)
I’ve took a test with this question
Other Questions
Find the equation of the line parallel to -2x +y = 3, that passes through the point(-3,-1). Write your answer in slope-intercept form. Do not use spaces in youranswer. Enter any fractions like a/b or -a/b. For photographers who document events like war, natural disasters, and crime scenes, it is important to be sensitive to the individuals involved and their families. O True O False When the partial pressure of O2 in venous blood is 30 Torr, the saturation of myoglobin with O2 is _______, while the saturation of hemoglobin with O2 is ______. A store pays $81 for a hockey stick and marks the price up by 5%. What is the amount of the mark-up? Calculate the measure of PMU and UPM.m PMU =m UPM = Egyptian Life of Extremes: In ancient Egypt the pharaoh was at the top of the pyramid and his family, noble people who owned land, and the priests came after. Scribes, architects and doctors were well off, and skilled craftsmen also had many privileges. Peasants and unskilled workers were low down the scale of Egyptian society, but it was the servants and slaves that skirted the bottom of the class pyramid. Those working in mines and quarries were really asking for trouble, as diseases, physical strain and dangers lurked in every turned stone in the desert. Slaves working in rich domestic environments were the lucky ones as they were assured security, housing and food.Men in the armed forces, army and navy were not afforded a high social status, and neither were entertainers. Professions were usually hereditary, not chosen; a man followed his fathers trade and so on. Scribes were the top dogs in the sphere of learning and teaching. Not every child was able to learn how to read and write; this was restricted to those following the scribe profession.Most Egyptians ate bread, fruits, and vegetables such as dates, figs, and beans on a daily basis. The wealthy ate different kinds of meat such as beef, veal, antelope and gazelle meat. The poor ate mostly birds such as geese, ducks, quails, and cranes. Different fish from the Nile were consumed, which were frequently dried in the sun. The poor drank beer while the rich drank fine wine.Clothing was made from linen. Babies and infants often went naked so as not to ruin clothing. Women wore long tunics like dresses, while men wore knee length tunics. Both would wear jewelry, perfume, and wigs if they could afford such items. The wigs were made with sheep or real human hair, and worn at parties and in domestic environments as well as at festivals.What is the topic of this reading passage? (RA form)What is the main idea of this reading passage? (RACE) A scientific ________ must have a control, so that the variables that could affect the out come is reduced. A:experiment B:conclusion. C:investigation. D:reasoning (8+r)4It's simple but I wanna check if my messy self is actually right lol A cook is making large fruit salads. He has 51 bananas, 41 pears, 25 peaches, and 56 apples. He needs 4 bananas, 3 pears, 2 peaches, and 5 apples for each salad. How many complete fruit salads can the cook make? WILL GIVE BRAINLIEST PLS HURRY Eating around chemicals in the work place is considered safer because todays chemicals are more diluted than in the past simplify: 2/3m + m - 1 2/3m Which type of electromagnetic waves make up the colors of a rainbow seen after a storm?A. visible lightB. infrared lightC. X-raysD. ultraviolet light HELPPPPPP AAA IM DYING HERE whats angel island? Hurry Use the order of operations to simplify the following expression.16+(14-6)x3-62-6O 18O None of the other answers are correctO 780 34O 12 Is this true or false? To protect interest in imperalized countries, Europeans built up their military. If you are buying at item at a store for a price of $72, and there is a 6.2% tax added on top, what would be the total amount due at the register, to the nearest cent? i neeeeed a girl that is looking for true love, trust me i will love her How many grams are there in 0.75 moles of Sodium HEY CAN ANYONE PLS ANSWER DIS MATH PROBLEM!!!!