In Engineering, the thrust angle is checked by referencing: C. vehicle centerline.
What is a thrust angle?A thrust angle can be defined as an imaginary line which is drawn perpendicularly from the centerline of the rear axle of a vehicle, down the centerline.
This ultimately implies that, the thrust angle is a reference to the centerline (wheelbase) of a vehicle, and it confirms that the two wheels on both sides are properly angled within specification.
Read more on thrust angle here: https://brainly.com/question/13000914
#SPJ1
What type of diagrams are used to present the conditions that are available to control outputs based on inputs?
A. Panel
B. Ladder
C. Schematic
D. Block
The type of diagrams used to present the conditions that are available to control outputs based on inputs are called; B: Ladder
How to Utilize Ladder Diagrams?Ladder diagrams are defined as specialized schematics usually used to document industrial control logic systems.
Now, these are called ladder diagrams due to the fact that they resemble a ladder, with two vertical rails that supply power and as many “rungs” as there are control circuits to represent.
Read more about Ladder Diagrams at; https://brainly.com/question/20519838
#SPJ1
What must the controlling contractor include in the written notification he or she provides?
A. Any repair to the crane
B. Any repair to the anchor bolts
C. Any changes to the company's human relations (HR) policies
D. Any changes to the training program
The controlling contractor includes in the written notification he or she provides A. Any repair to the crane.
What is the training program?An excessive contractor, big contractor, manufacturing manager or each different crook entity, which has the overall duty for the improvement of the project - its planning, splendid and completion."
The delivery director is described with the useful resource of the use of ASME due to the fact the birthday celebration that straight away oversees the artwork being finished with the useful resource of the use of the crane and the associated rigging crew. According to ASME B30. 5, a lift director ought to be onsite for all lifting operations.
Read more about the contractor :
https://brainly.com/question/26368971
#SPJ1
Starters that are intended to protect motors that operate on 240 volts should contain ____ load contacts.
Zone, n = (sum of digits of your student id)% 8 for example, if your student id is 17301283, zone = (1+7+3+0+1+2+8+3) % 8 = 25 % 8 = 1 derive midpoint line drawing algorithm for a line in zone n. if you find zone 0, i.e., then drop the last digit from sum and take % 8 again. if your student id is 16240524, zone = (1+6+2+4+0+5+2+4)%8 = 24%8 = 0 updated zone by removing last digit 4 = (1+6+2+4+0+5+2)%8 =20%8 = 4 derive midpoint circle drawing algorithm for the arc of the circle in zone n. if you find zone 1, i.e., then drop the last digit from sum and take % 8 again. if your student id is 17301283, zone = (1+7+3+0+1+2+8+3)%8 = 25%8= 1 updated zone by removing last digit 3 = (1+7+3+0+1+2+8)%8 = 22%8= 6
If the piston in problem 3 had an input of 50 psi, what would the total amount of work performed by one piston be?
Answer:
Applied pressure on piston (P) = 50 psi. We know that work done is given by W = Force x displacement. S Force = Pressure x Areas > W = ( PXA ) X L W = PX ( AL ) W = PX AV = 50x 43.7088. W= 2185.
Please give me brainliest - you get 25% as well! I swear!
A 20cm-long rod with a diameter of 0.250 cm is loaded with a 5000 N weight. If the diameter of the bar is 0.490 at this load, determine: I. the engineering stress and strain, and [2] II. the true stress and strain
If the diameter of the bar is 0.490 at this load, determine I. the engineering stress and strain, and [2] II. the true stress and strain is 1561. 84 MPa.
What is strain?Strain is a unitless degree of ways a great deal an item receives larger or smaller from an implemented load. Normal stress happens while the elongation of an item is in reaction to an everyday pressure (i.e. perpendicular to a surface), and is denoted via way of means of the Greek letter epsilon.
L = 20 cm d x 1 = 0.21 cmdx 2 = 0.25 cmF=5500 a) σ= F/A1= 5000/(π/4x(0.0025)^2)= 1018.5916 MPa lateral stress= Ad/d1= (0.0021-0.0025)/0.0025 = - 0.1 longitudinal stress (ɛ_l)= -lateral stress/v = -(-0.16)/0.3(assuming a poisson's ration of 0.3) ε_l=0.16/0.3 = 0.5333b) σ_true= σ(1+ ɛ_I)= 1018.5916(1+0.5333 = 1561.84 MPa.Read more about the diameter :
https://brainly.com/question/358744
#SPJ1
Gasoline and diesel fuel are made from what fossil fuel?
Answer:
they are made from petroleum
The most important reason to wear your seat belt is to protect you from:
Answer:
#1. Saves Lives. The bottom line is seatbelts save lives.
Explanation:
Tech A says that water soaked brake shoes can be a cause of brake fade. Tech B says that disc brakes dissipate heat faster than drum brakes. Who is correct
Explanation:
perturbateur ( le temps, le lieu, les personnages[description], la victime, l'enqueteur )
les peripeties
le denouement
Two sides and the included angle of triangle were measured as under
A = 757.64 +0.045 m
B = 946.70+ 0.055 m
C = 54°18+25"
Based on the calculations, the area of this triangle is equal to 290,136.87 m².
Given the following data:
Side A = 757.64 +0.045 m.Side B = 946.70+ 0.055 m.Angle, C = 54°18'25"How to calculate the area of this triangle?Mathematically, the area of a triangle can be calculated by using this formula:
Area = 1/2 × b × h
Where:
b is the base area.h is the height.In this scenario, the area of this triangle is given by:
Area = 1/2 × a × b × sinC
Substituting the given parameters into the formula, we have:
Area = 1/2 × 757.64 × 946.70 × sin(54°18'25")
Area = 580,273.74/2
Area = 290,136.87 m².
Next, we would determine the probable error of the area by using this formula:
[tex]PE_A = \pm k \sqrt{PE} \\\\PE_A = \pm \frac{1}{2} \times sinC \sqrt{(aPE_b)^2 + (bPE_a)^2 } \\\\PE_A = \pm \frac{1}{2} \times sin(54^{\circ}18'25") \times \sqrt{(757.64 \times 0.045)^2 + (946.70 \times 0.055)^2 } \\\\PE_A = \pm 0.4045 \times \sqrt{1,162.39 +2,711.12}\\\\PE_A = \pm 0.4045 \times \sqrt{3,873.51}\\\\PE_A = \pm 0.4045 \times 62.2375\\\\PE_A = \pm25.1751 \;m^2[/tex]
Therefore, probable error of the area is equal to ±25.1751 m².
Read more on area of triangle here: brainly.com/question/21917592
#SPJ1
Complete Question:
Two sides and the included angle of a triangle were measured and the probable error of each value were computed as follows:
A = 757.64 +0.045 m
B = 946.70+ 0.055 m
C = 54°18'25"
Determine the area of the triangle and the probable error of the area.
Consider a cup on a dinning table half filled with water.
State 5 similarities and differences between the fluids that are contained in the cup.
Answer:
color, shape container, type, amount, temperature
Explanation:
Which important feature of a block-based coding language like Scratch is not
a feature in a text-based coding language like C++?
Answer:Block-based coding requires a different type
Explanation:
TV
When writing a programme, text-based programming languages give programmers more in-depth control over lower-level functionality.
What is block-based applications?In block-based applications, we are constrained to use the blocks that are provided to us and frequently have a limited range of options for doing so. We have more freedom to customise lower-level functionality in text-based languages since we are not constrained by a predetermined number of available blocks.
Python is usually used for making websites and applications, automating repetitive tasks, and analysing and display of data. Python has been utilised by many non-programmers, including accountants and scientists, for a different kind of routine activities including managing finances since it is very simple to learn.
Therefore, When writing a programme, text-based programming languages give programmers more in-depth control over lower-level functionality.
To learn more about Python on:
brainly.com/question/18502436
#SPJ7
Select the parameters that are included in a baseline performance check. you may select more than one. select one or more: a. compressor body temperature b. condenser fan rpm c. discharge pressure d. compressor amp draw e. suction pressure f. discharge line temperature previous page
Answer:
A F E C D B
Explanation:
Performance testing can be done with quantitative tests that are run in a lab or, in some situations, in a real-world setting. Performance requirements must be determined and tested.
What parameters included in a baseline performance check?Commonly used criteria include things like processing speed, data transfer rates, network bandwidth and throughput, workload efficiency, and dependability.
Baseline testing is the process of confirming the accuracy of the documents and requirements upon which test cases are based.
A baseline is a benchmark that serves as the foundation for any new production, generally speaking. This is the benchmarking of the application's performance in software testing.
Performance testing requires the design, normal and peak loads, system resources, dependencies, workload characteristics, and time, all of which should be considered in any method.
Therefore, A baseline is a set timeline that serves as the benchmark against which the project's performance is evaluated.
Learn more about performance here:
https://brainly.com/question/15466511
#SPJ2
which of the following elements does not affect the strength and usefulness of concrete
A voltage drop test is being performed on the output wire of the alternator to the battery positive post. Technician A says that the voltage drop should be more than 0.5 volts. Technician B says that during the voltage drop test, the engine should be at the specified rpm and the battery loaded down so the alternator puts out maximum current flow. Who is correct
Assuming a voltage drop test is being performed on the output wire of the alternator to the battery positive post, the technician who would be correct is: B. Technician B.
What is a voltage drop?A voltage drop can be defined as a measure of the decrease in electrical potential in an electrical circuit, especially along the path of a current that is flowing through it.
How to calculate the amount of voltage?In order to determine the amount of voltage that is running through this circuit, we would apply Ohm's law:
V = IR
Where:
I represents the current.R represents the resistance.V represents the voltage.Assuming a voltage drop test is being performed on the output wire of the alternator to the battery positive post, the technician who would be correct is Technician B because the engine should be at the specified rpm.
Read more on voltage drop here: https://brainly.com/question/14549040
#SPJ1
Complete Question:
A voltage drop test is being performed on the output wire of the alternator, between the alternator output wire to the battery positive post. Technician A says that the voltage drop should be approximately 12.0 volts. Technician B says that during the voltage drop test, the engine should be at the specified rpm and the battery loaded down so the alternator puts out maximum current flow. Who is correct?
A. Technician A
B. Technician B
C. Both Technician A and B
D. Neither Technician A nor B
What is the purpose of having a ventilation system on board a motorized vessel?.
The purpose of having a ventilation system on board a motorized vessel is : To remove flammable gas from a vessel to avoid explosions.
Meaning of ventilation systemA ventilation system can be defined as a system that allows for removal of gases from a vessel to the atmosphere.
A Ventilation system is very important in every motorized vessel because they help to eliminate or remove flammable gases that are dangerous and are liable to explode when held in a large amount in the engine.
In conclusion, The purpose of having a ventilation system on board a motorized vessel is to remove flammable gas from a vessel their by avoiding explosions.
Learn more about Ventilation System: https://brainly.com/question/1687520
#SPJ4
A dice is thrown 420 times and the number 6 is obtained 63 times; express the frequency of obtaining
the number 6 as a percentage.
Answer: 15%
Explanation:
Frequency of obtaining = 63/420 = 0.15 = 15%
explain why it is not advisable to wear Ornament like ring at work shop
The reason that it is not advisable to wear Ornament like ring at work shop is that rings can be easily get caught and fingers or the hands of the person can be injured, cut, scared etc.
Why should you not wear a ring at work?Jewelry is known to bring about a lot of safety hazards for people working around chemicals and others.
Note that the reason that it is not advisable to wear Ornament like ring at work shop is that rings can be easily get caught and fingers or the hands of the person can be injured, cut, scared etc.
Learn more about Ornament from
https://brainly.com/question/24286720
#SPJ1
The code requires switches to be
installed at
entrance to a room.
A. every
B. every other
C.Only one
The code requires switches to be installed at every entrance to a room.
What is every?In English language, every can be defined as a determiner and it is typically used before a singular noun while referring to each of the members of a set without exception.
In this context, every is the most appropriate word to use in filling the blank because entrance is a singular noun while the room is a set.
Therefore, the code requires switches to be installed at every entrance to a room.
Read more on determiner here: https://brainly.com/question/3620820
#SPJ1
what is difference between baseband transmission and broadband transmission
The difference between the baseband and the broadband connection is made with the transmission of signal over the frequency.
What is data transmission?The data transmission is given as the transfer of the data from one digital device to another. The transmission can take place with the baseband transmission and the broadband transmission.
The major difference between the two transmissions is that the baseband utilizes a complete frequency for transmission of signal, while the transmission with the broadband is made with multiple signals over multiple frequencies.
Learn more about broadband signals, here:
https://brainly.com/question/19204110
#SPJ1
Write a C++ program to get the following output. 1 12 123 1234 12345
#include"stdafx.h"
#include<iostream>
usingnamespace std;
int main()
{
for(int i=1; i<=5; i++)
{
for(int j=1; j<=i; j++)
{
cout<<j ;
}
cout<<endl;
}
system("pause");
return 0;
}
4.6. What is the maximum peak output voltage and current if the supply voltages are changed to +15 V and -15 V.
The maximum peak output voltage and current if the supply voltages are changed to +15 V and --1V will be 15V and 0.1A.
How to calculate the current?From the information given, the supply voltages are +15V and -15V. The maximum peak output voltage will be 15V.
The maximum peak current will be:
= 15/150
= 0.1A
In conclusion, the maximum peak output voltage and current will be 15V and 0.1A.
Learn more about current on:
brainly.com/question/24858512
#SPJ1
Name the force acting on the handles of a plastic shopping bag that is full of groceries.
The answer is
The force acting on the handles of a plastic shopping bag that is full of groceries are gravitational force, muscular force.
Gravitational force works downwards, and muscular force is applied by the hands lifting bucket upwards. Two forces are in the opposite direction and hence balancing each other. As a result net force is zero.
Learn more things about gravitational and muscular force
https://brainly.com/question/20939728
If an internally piloted DCV does not shift, you should use a gauge to _____. A.check the pilot line pressure b. check the inlet pressure to the DCV c. check the outlet pressure from the DCV d. check the vacuum on the pilot line
If an internally piloted DCV does not shift, you should use a gauge to: B. check the inlet pressure to the DCV.
What is DCV?DCV is an acronym for Directional Control Valve and it can be defined as a fundamental part of pneumatic and hydraulic systems, which is designed and developed to enable fluid from one or more sources flow into different paths.
In pneumatic and hydraulic systems, you should use a gauge to check the inlet pressure to the DCV when an internally piloted DCV does not shift.
Read more on Directional Control Valve here: https://brainly.com/question/26153256
#SPJ1
the diagram illustrates a method of producing plastics called
Answer:
polymerisation,
Explanation:
A visual lead of ________ seconds or 1 city block is appropriate when driving in traffic in urban areas.
The answer is
A visual lead of 12-15 seconds or 1 city block is appropriate when driving in traffic urban areas.
Urban driving involves a variety of complex driving situations.
when you driving in urban areas, look at least 12-15 seconds ahead of vehicle.
Learn more things about driving in urban areas
https://brainly.com/question/26896194?source=archive
Answer: 5
Explanation:
just took it
A 100-horsepower, three-phase squirrel-cage induction motor is connected to a 240-volt line. A dual-element time-delay fuse is to be used as the short-circuit protective device. What is the correct fuse rating
Based on the National Electrical Code (NEC), a 450-Ampere fuse should be used to protect this polyphase (three-phase) squirrel cage inductor motor.
Given the following data:
Power rating = 100-horsepower.Voltage = 240 volt.How to determine the correct fuse rating?According to Table 430.52 of the National Electrical Code (NEC), a dual-element time delay fuse should be calculated at 175% (1.75) of the full-load current rating for an alternating current (AC) polyphase (three-phase) squirrel cage inductor motor.
In this scenario, the squirrel cage inductor motor didn't list a NEMA design code on its nameplate. Thus, we'll assume that the inductor motor is design B and its fuse rating is given by:
Fuse rating = 248 × 1.75 × 434
In conclusion, the nearest standard fuse size which is above the computed value listed in Section 240.6 of the National Electrical Code (NEC) is 450 amperes.
Read more on National Electrical Code here: brainly.com/question/10619436
#SPJ1
A heating element for a cooking appliance is stretched too far during installation. What action can be performed? A. Dispose of the element and purchase a new one. B. Chill the element in a freezer to shrink it. C. Cut the element to shorten it. D. Recoil the element over a rod.
Because the heating element for a cooking appliance is stretched too far during installation, Dispose of the element and purchase a new one.
What is meant by heating element?The Definition of heating element is known to be the aspect of an electric heating appliance where the electrical energy is said to be changed to heat.
Note that Because the heating element for a cooking appliance is stretched too far during installation, Dispose of the element and purchase a new one.
Learn more about heating element from
https://brainly.com/question/4428189
#SPJ1
a ________________ is the flat, low-lying area adjacent to a stream channel that receives overbank flow
Answer:
flood plain
Explanation:
it should be called a flood plain which makes sense because it’s not a deposition.
Most regulatory signs are?
Answer:
Most regulatory signs are square or rectangular except for STOP signs, which are octagonal, and YIELD signs, which are equilateral triangles with one point straight down.
Explanation:
Answer:
Most regulatory signs are square or rectangular except for STOP signs, which are octagonal, and YIELD signs, which are equilateral triangles with one point straight down.
Please give me brainliest - you get 25% as well! I swear!