Answer: it's c. ← 63 N and → 73 N
Explanation:
Struggling with this, pls answer:( Brainliest to the (FIRST) right answer
Answer:
c. a and c
Explanation:
ammeters are connected in series to measure charge/current
A 4.0-W resistor, an 8.0-W resistor, and a 10.0-W resistor are connected in series across an 11-V battery. What is the total voltage drop across the 4.0-W and 8.0-W resistors?
can anyone solve this quick?
Answer:
yes
Explanation:
First show me your or
Question 1 of 10
What is the wavelength of a wave with a frequency of 262 Hz and a speed of
343 m/s?
O A. 1.3 m
OB. 89,866 m
O C. 1.11 x 10-5 m
O D. 0.76 m
SUBMIT
Answer:
V = λ f (wavelength * frequency)
λ = V / f = 343 m/s / 262 / s = 1.3 m
How does the kinetic energy from the forward motion of a car traveling at 16 m/s
compare with the kinetic energy of the same car traveling at 8 m/s?
(A) It is 2 times greater.
(C) It is 8 times greater.
(B) It is 4 times greater.
(D)
It is 16 times greater.
The kinetic energy in the first case is 4 times more than the second case.
Hence, option D)It is 4 times greater is the correct answer.
What is Kinetic Energy?Kinetic energy is simply a form of energy a particle or object possesses due to its motion.
It is expressed as;
K = (1/2)mv²
Where m is mass of the object and v is its velocity.
Given that;
For the first case, velocity v = 16m/sFor the second case, velocity = 8m/sLet the mass of the car be mFor the first case, kinetic energy of the car will be;
K = (1/2)mv²
K = (1/2) × m × (16m/s)²
K = (1/2) × m × 256m²/s²
K = mass × 128m²/s²
For the second case, kinetic energy of the car will be;
K = (1/2)mv²
K = (1/2) × m × (8m/s)²
K = (1/2) × m × 64m²/s²
K = mass × 32m²/s²
Comparing the kinetic energy of the car with the same mass but different velocity, we can see that the kinetic energy in the first case is 4 times more than the second case.
Hence, option D)It is 4 times greater is the correct answer.
Learn more about kinetic energy here: brainly.com/question/12669551
#SPJ1
the unit of energy is a derived unit give reasons.
Answer:
ioinl
Explanation:
sandra is riding a bice at 10.0 meters/second. she slows down to 2.0 meters/second in 10 seconds. her acceleration is blank meters/seconds^2
Explanation:
[tex]a = \frac{v - v _{i} }{t} [/tex]
Her intial velocity is 10
Her final velocity is 2
Time is 10 seconds.
[tex]a = \frac{2 - 10}{10} [/tex]
[tex]a = - \frac{4}{5} [/tex]
A bus starts from rest.if the acceleration is 2m/s square, find
i.the distance travelled
ii.the velocity after 2 seconds.
Answer:
The velocity after 2 seconds can be found through:
V = u +a*t
Where V is final velocity, u is initial velocity, a is acceleration and t is time.
V = 0 + 2* 2= 4 meters/second
The distance (s) can be found through:
V^2= u^2 +2*a* s
Where V is final velocity, u is initial velocity, a is acceleration.
4^2= 0^2 + 2 *2*s
16= 0 + 4s
s= 4 meters
Distance (s) can also be found through:
s= ut + 1/2 at^2
s= 0+ 1/2 *2*2^2= 1 *2*2
s= 4 meters
Explanation:
a student investigates the efficiency of a scale model of an electricity generating wind turbine using the equipment in figure 1.
the student changed the number of sales on the turbine and measures the power output from the turbine's generator. the air blower is supplied with 533w and has efficiency of 0.62.
when using two sails, the efficiency of turbine was 13%. calculate the power generated.
The power generated or output power of the turbine is determined as 42.96 W.
Power generated
The power generated or output power of the turbine is calculated as follows;
eff = 0utput power/1nput power x 100%
13 = 0utput power/(0.62 x 533)
0.13 = 0utput power/330.46
0utput power = 0.13 x 330.46
0utput power = 42.96 W
Thus, the power generated or output power of the turbine is determined as 42.96 W.
Learn more about 0utput power here: https://brainly.com/question/20038729
#SPJ1
Just the answer (PLSS)
What mindset do you believe Einstein had while alive and what do you think the key component or constant action was for Einstein throughout his “miracle year”?
The miracle year for Albert Einstein was the year 1905 within which he published so many renowned papers.
When was Einstein miracle year?The miracle year for Albert Einstein was the year 1905 within which he published so many renowned papers in a short time and became very popular.
His mindset in that year was one that challenged the orthodox explanations and sought to think outside the box.
Learn more about Albert Einstein:https://brainly.com/question/2964376
#SPJ1
Throughout the spring and summer, trees take nutrients
from the soil. these nutrients are spread throughout the
tree. in the autumn, some of these nutrients are lost
when the tree drops its leaves.
in a young, rapidly growing forest, scientists calculated
that 23 kilograms of a nutrient are taken up from the soil
by the trees in one year. in the autumn, the leaves that
fall contain 21 kilograms of the nutrient.
18 the trees can be considered a subsystem of the
larger ecosystem. if there are no other inputs or outputs from the trees, how much of the nutrient
is added to the tree subsystem (stored in the trees) in this year?
a. 2 kg
b. 21 kg
c. 23 kg
d. not enough information is available to determine.
(help!!!!) science
The amount of nutrients added to the tree subsystem in one year after leaf fall is 36 kg of nutrients.
What are plant nutrients?Plants nutrients are the mineral elements required by plants for their growth and development.
Plant nutrients are mostly obtained from the soil as well as from the atmosphere.
Based on the data provided, each tree will absorb 23 - 21 Kg nutrients = 2 kg of nutrients
18 trees will absorb 18 × 2 = 36 Kg of nutrients.
Therefore, the amount of nutrients added to the tree subsystem in one year after leaf fall is 36 kg of nutrients.
Learn more about plant nutrients at: https://brainly.com/question/14366476
#SPJ1
Which is one factor that contributes to the formation of polar, temperate, and tropical zones?
the angle of the Sun’s rays
the direction of seasonal winds
the presence of prevailing winds
the movement of wind near a mountain
help im timed
Answer:
The angle of the Sun's rays:
At about June 21 the sun is directly overhead at about 23 deg north of the equator
On about Dec 21 the sun is directly overhead at about 23 deg south of the equator
It is this tilt 23 deg to the ecliptic (path of earth about sun) that causes the major temperature changes on earth
The frequency of a wave does not change as it passes from one medium to another.
What will most likely happen if a light wave moves from the air into a solid?
The wavelength of the light wave will increase.
O The speed of the light wave will decrease
The wavelength of the light wave will remain the same.
O The speed of the light wave will remain the same.
Mark this and return
Save and Exit
Next
Answer:
The speed of the wave will decrease (due to a shorter wavelength after passing from air to a more dense medium)
An engineer is working to design a bouncy ball that conserves all of its kinetic and potential energy. She drops the ball to the ground from a height of 3 meters. If it really works, how high should the ball bounce
If potential energy is conserved or remain the same, the ball will bounce 3 m high.
Conservation of energyThe principle of conservation of energy states energy can neither be created nor destroyed but can be converted from one form to another.
If we apply the principle of conservation of energy, the total potential energy will remain the same.
P.E(initial) = P.E(final)
Thus, If potential energy is conserved or remain the same, the ball will bounce 3 m high.
Learn more about potential energy here: https://brainly.com/question/1242059
#SPJ4
Where do the three rays in a ray diagram start?
at a focal point on the opposite side of the lens
at three different points on the object
at a focal point on the same side of the lens
at a single point on the object
The three rays in a ray diagram start from a single point on the object.
What is focal point of a lens?The focal point of a lens is the point where light rays parallel to the axis are brought to a point.
The focal point is responsible for the converging of light rays coming from the object but the rays do not start here.
Thus, the three rays in a ray diagram start from a single point on the object.
Learn more about ray diagram here: https://brainly.com/question/23536244
#SPJ1
Answer:
D
Explanation:
on which factor potential energy depends?
[tex]\large{\underline{\underline{\pmb{\frak {\color {red}{Question:}}}}}}[/tex]
[tex] \sf \red{what \: is \: potential \: energy}[/tex]
[tex]\large{\underline{\underline{\pmb{\frak {\color {blue}{Answer:}}}}}}[/tex]
Potential energy: A type of energy which is possessed by an object due its position.
Example: A raised weight or when we raise any weight is a potential energy.
[tex]\large{\underline{\underline{\pmb{\frak {\color {red}{Question:}}}}}}[/tex]
[tex] \sf \red{on \: which \: factor \: potential \: energy \: depends}[/tex]
[tex]\large{\underline{\underline{\pmb{\frak {\color {blue}{Answer:}}}}}}[/tex]
Potential energy depends upon three factors. They are:
Mass of an object. Height of an object. Gravitational force upon an object.[tex] \boxed{ \huge \frak \red{brainlysamurai}}[/tex]
4. if the experiment had been repeated with frequencies 10 times lower than those in table 5.2,
what effect would that have on the experiment? (1)
If the experiment had been repeated with frequencies 10 times lower than those in table 5.2, then Vc will increase 10 times to the values given in the table.
What is frequency?It is the number of oscillations per second of the sinusoidal wave.
Vc is the voltage across the capacitor and Xc is the capacitive reactance.
Xc = - 1/2πfC
where f is the frequency and C is the capacitance of the capacitor.
If the frequency is lowered, the potential difference will increase because frequency is inversely proportional to the voltage.
Thus, Vc will increase by lowering the frequency by 10 times.
Learn more about frequency.
https://brainly.com/question/13758580
#SPJ1
17. what does it mean if a personality
test is reliable?
a. a reliable test will give consistent
results over time.
b. a reliable test reveals forgotten
experiences.
c. a reliable test has strong personal
bias.
d. a reliable test accurately predicts?
your actions.
A Personality test is said to be reliable because (A). a reliable test will give consistent results over time.
Meaning of Personality testPersonality test can be defined as a test that can be used to verify or ascertain an individuals personality.
Personality test is a test that is carried out by different organizations to help to help them know the individuals in that organization and to help others know how to relate and work with them.
In conclusion, A Personality test is said to be reliable because a reliable test will give consistent results over time.
Learn more about Personality test: https://brainly.com/question/1360758
#SPJ1
Answer:
a.
Explanation:
You are working with an existing fiber optic installation in your building. you want to know the length of each cable that runs through the walls.which tool should you use
Answer:
you will use the OTDR tool ti will very much so help
Explanation:
as the moon phase approaches full we say the Moon is doing what
As the moon phase approaches full we say the Moon has now completed one half of the lunar month.
What is Lunar month?This is defined as the time it takes the Moon to pass through all of the phases.
When the moon approaches full then itn has completed one half of the lunar month which is the time taken to form a new moon.
Read more about Moon here https://brainly.com/question/18517840
#SPJ1
In the reaction below, how would adding more of product C affect the equilibrium of the system? (2 points) A + B ⇄ C + D Group of answer choices Shift it to the right toward the products. Shift it to the left toward the reactants. Equally create more products and reactants. It would have no effect.
Answer:
identify the action reaction force in the following cases
a boy walking on the ground
firing a bullet from the gun
a book lying on the table
a boy swimming in the swimming pool
launching of a rocket from the earth surface
Answer:
A Shift it to the right towards the products
Explanation:
If more reactants or products are added to a reaction system at equilibrium, the equilibrium will shift away from what was added to lower its concentration. If a reactant or product was removed from a reaction system at equilibrium, the equilibrium systems will shift to replace some of what was removed.
Which of the following would have the smallest coefficient of kinetic friction when slid along your hang.
a Bar of Soap
carpet
sand paper
can someone do this for me please?! Just the answer pls
4. The answer is that you will see the same sights as when you are resting. That is because you and mirror are in rest one relative another. If your relative speed is 0, it doesn't matter how quickly you both travel in relation to other objects.
5. The relativistic effects will not alter if the speed of light is reduced to 50m/s. According to the principle of constancy (2nd postulate), the upper limit of speed is 50m/s, which will be impossible for material objects to achieve because as the speed of light decreases, the sizes of humans and all other materials decrease as well, decreasing our relativistic velocity and thus making c=50m/s unattainable for material objects, and thus the relativistic effects will remain unchanged. A pedestrian must use caution when crossing the roadway. Let's assume you see a car arriving at 60 kilometers per hour, or 16.666 meters per second, from a distance of 100 meters. It'll take 6 seconds to arrive, giving you plenty of time to cross the street. Because the light reflected from the car to your eyes left the car two seconds ago, the car will reach at your location in four seconds and hit you (if the car is travelling in the lane on the far side of the road). It looks to you that approaching automobiles traveling at the legal limit are traveling at a speed of 100 / 4 = 25 m/s, which is 50% faster than the genuine speed of 16.666 m/s. When considering whether or not it is safe to cross the road, one would quickly become accustomed to this.
6.
Which two statements are true of electromagnetic waves?
Answer:
I think it is A and D
Explanation:
During the time interval from 0.0 to 10.0 s, the position vector of a car on a road is given by x(t) = a + bt + ct2, with a = 17.2 m, b = -10.1 m/s, and c = 1.10 m/s2. What is the car’s velocity as a function of time? What is the car’s average velocity during this interval?
im stuck with this :(
The car’s velocity as a function of time is b + 2ct and the car’s average velocity during this interval is 0.9 m/s.
Average velocity of the carThe average velocity of the car is calculated as follows;
x(t) = a + bt + ct2
v = dx/dt
v(t) = b + 2ct
v(0) = -10.1 m/s + 2(1.1)(0) = -10.1 m/s
v(10) = -10.1 + 2(1.1)(10) = 11.9 m/s
Average velocityV = ¹/₂[v(0) + v(10)]
V = ¹/₂ (-10.1 + 11.9 )
V = 0.9 m/s
Thus, the car’s velocity as a function of time is b + 2ct and the car’s average velocity during this interval is 0.9 m/s.
Learn more about velocity here: https://brainly.com/question/4931057
#SPJ1
Shyam saw a cylindrical copper rod in his store room he realise that it can be used for various purposes it can be used as a flower ways by covering it one side face with any metal it can be used as a conductor or it can be used as a cylindrical box by covering both the side face with metal he measure the radius of the rod with 3% and length of rod with 7% error error percentage is measuring the volume of the cylinderical box is
The error percentage in measuring the volume of the cylindrical box is 6.3 x 10⁻³ %
Error percentage in measuring the volume of the cylinder
The total error percentage in measuring the volume of the cylinder is calculated as follows;
Volume of cylinder = πr²h
Volume of cylinder = π(0.03r)²(0.07h)
Volume of cylinder = (6.3 x 10⁻⁵)πr²h
Error in measuring the volume = 6.3 x 10⁻⁵ x 100% = 6.3 x 10⁻³ %
Learn more about percentage error here: https://brainly.com/question/5493941
#SPJ1
After travelling 4.0 km, the train reaches its maximum speed. it continues at this constant speed on the next section of the track where the track follows a curve which is part of a circle.
state the direction of the resultant force on the train as it follows the curved path.
Answer:
toward the center of the circular curve
Explanation:
An object will follow a circular path at constant speed if and only if its net acceleration is constant and directed toward the center of the curved path.
__
The result force is directed toward the center of the circle.
_____
Additional comment
If any part of the result force is in the direction of motion, the speed will not be constant. If the center-directed force is not constant, the path will not be circular.
a car takes 125 ft to brake from 60 to 0 mph. Assume that the acceleration of the Prius is constant while braking. Find how long it takes for the Prius to come to a stop. Long problems begin on the next page
Answer:
2.84 seconds
Explanation:
t = ?
distance = 125
Velocity origianal = 60 m/hr = 88 ft/s
AVERAGE velocity = 88/2 = 44 ft/s
44 t = 125
t = 125/44 = 2.84 s
A car with a mass of 1000 kg is moving on an un-banked ramp with a radius of 100 m. what is the maximum speed the car can move without skidding if the coefficients of static and kinetic friction are 0.80 and 0.60 respectively
The maximum speed the car can move without skidding is determined as 28 m/s.
Maximum speed of the car
The maximum speed of the car moving in a circular path is provided by static frictional force.
Fs = μFₙ = mv²/r
μFₙ = mv²/r
mv² = μFₙr
v² = μFₙr/m
[tex]v_{max} = \sqrt{\frac{\mu_s F_n r}{m} } \\\\v_{max} = \sqrt{\frac{\mu_s (mg) r}{m} } \\\\v_{max} = \sqrt{\mu_sgr} \\\\v_{max} = \sqrt{(0.8)(9.8)(100)}\\\\v_{max} = 28 \ m/s[/tex]
Learn more about maximum speed here: https://brainly.com/question/4931057
#SPJ1
When electricity is “used” or we say that energy is “wasted,” what is actually happening?
Answer:
Wasted energy is energy that is not usefully transferred or transformed. Energy cannot be made or destroyed. Energy is transformed into a different form that can be used. When energy is transformed or transferred only part of it can be usefully transformed or transferred.