Answer:
- 30 kW
Explanation:
IDEA:
Power of an object that does work(source) is given by:
[tex] \boxed{ \mathsf{power = \frac{work \: done}{time} }}[/tex]
where work done is mostly shown as the Force applied on an object to Displace it through some distance in the same direction as the Force.
[tex] \boxed{ \mathsf{ work = force \times displacement}}[/tex]
___________________
INFORMATION:
In the question,
The source of power is the crane, while the object is a load of 36000N.
Note, what's given is the force, not the mass. Since, the SI unit of mass is kg and that of Force is Newton(N).
[The weight of the load is represented in Newton, since weight of an object is the amount of Force with which the Earth attracts that object]
I) work done
So,
Force = 36000NDisplacement = 50 m=> Work = 36000 × 50
= 1,800,000 J
(The SI unit of work is Joules(J)).
___________________
II) power
After getting the amount of work done, now we have to place it in the formula for power.
That is:
[tex] \boxed{ \mathsf{power = \frac{work \: done}{time} }}[/tex]
Note, During calculations, all quantities must be in their SI units.
SI unit for time is Seconds (s)
But the time we have is in minutes.
___________________
Converting time from minutes to Seconds:
1 minute = 60 Seconds.
Hence,
time = 60 s[tex] \implies \mathsf{power = \frac{1800000}{60} } \: [/tex]
=> power = 30,000 W
(SI unit of power is Watts(W))
To write four zeroes with a 3 and W is a lot of effort. So, we can look for simple expressions like kilowatts(kW) that can express bigger quantities in lesser terms.
1000 W = 1 kW
•°• 30,000 W = 30 kW.___________________
Direction and sign:
The crane displaces the load in an upward direction (from the term "lifts")
But, the Force is acting downwards, as the weight of the body is always towards the Earth.
Since, the directions of Force and displacement are opposite, a minus takes its place in front of both Work and power.
___________________
Therefore, the final answer will be:
Power of the crane = - 30 kWWhy is kinetic energy lost in an inelastic collision?
Answer:
This is because some kinetic energy had been transferred to something else.
Explanation:
An inelastic collision is a collision in which there is a loss of kinetic energy. While momentum of the system is conserved in an inelastic collision, kinetic energy is not.
60W of power is taken by a small electrical heater from a 12V supply Determine the current flowing through the heater
Answer:
5 amps
Explanation:
I = P/V
I = current (amps)
P = power (watts)
V = voltage (volts)
I = 60/12
I = 5
Which of the balls will exert the smallest force on object A?Why
what led scientists to the discovery of the strong nuclear force?
Answer:
Explanation:
The concept of a new strong nuclear force was introduced. In 1935, the first theory for this new force was developed by the Japanese physicist Hideki Yukawa, who suggested that the nucleons would exchange particles between each other and this mechanism would create the force.
Which statement most completely describes a Lewis electron dot diagram? A.
a representation of the electrons that form bonds in a molecule
B.
a representation of the total number of electrons in an element, compound, or ion
C.
a representation of the total number and arrangement of electrons in an element, compound, or ion
D.
a representation of the arrangement of valence electrons in an element, compound, or ion
Answer:
D.
Explanation:
it is indeed a representation of how the valence electrons in an element,coumpound, or ion are arranged.
to ensure you i was just quized on this and D is the correct anwser
A representation of the arrangement of valence electrons in an element, compound, or ion - statement most completely describes a Lewis electron dot diagram. Hence, option (D) is correct.
What is Lewis electron dot diagram?If the compound's molecular formula is known, electron dot structures or Lewis dot formulas can be drawn.
It describes the type of bond and the placement of the atoms within the molecule that are joined together. In honor of American chemist Gilbert Newton Lewis, molecules are depicted as having a Lewis electron dot structure or simply a Lewis structure.
Lewis dot structures, also known as electron dot structures, are schematics that show the interatomic chemical bonds in a molecule. Additionally, they show how many lone pairs there are overall in each of the atoms that make up the molecule. Common names for Lewis dot structures include electron dot structures and Lewis structures. Lewis described an acid as an electron pair acceptor, while a base is an electron pair giver.
Learn more about Lewis electron dot diagram here:
https://brainly.com/question/19093827
#SPJ2
how do you find average velocity (vaverage) from acceleration (a) and time (t)?
Answer:
1) Average velocities:
Given the magnitudes of 2 velocity vectors, in different time instants, the average velocity is defined as the difference of the 2 velocity magnitudes, in absolute value, divided by the interval of time occuring between the measurement of the velocity magnitudes.
2) Average acceleration
Given the magnitudes of 2 acceleration vectors, in different time instants, the average acceleration is defined as the difference of the 2 acceleration magnitudes, in absolute value, divided by the interval of time occuring between the measurement of the acceleration magnitudes.
As you see the definitions are pretty similar.
Note: I didn't copy-paste this answers from any other site.
a narrow slit is illuminated with sodium yellow light of wavelength 589 nm. if the central maximum extends to ±30.0°, how wide is the slit?
Answer:
because of the gravity of the earth
A 50 kg pitcher throws a baseball with a mass of 0. 15 kg. If the ball is thrown with a positive velocity of 35 m/s and there is no net force on the system, what is the velocity of the pitcher? â’0. 1 m/s â’0. 2 m/s â’0. 7 m/s â’1. 4 m/s.
The velocity of the pitcher at the given mass is 0.1 m/s.
The given parameters:
Mass of the pitcher, m₁ = 50 kgMass of the baseball, m₂ = 0.15 kgVelocity of the ball, u₂ = 35 m/sLet the velocity of the pitcher = u₁
Apply the principle of conservation of linear momentum to determine the velocity of the pitcher as shown below;
m₁u₁ = m₂u₂
[tex]u_1 = \frac{m_2 u_2}{m_1} \\\\u_1 = \frac{0.15 \times 35}{50} \\\\u_1 = 0.105 \ m/s\\\\u_1 \approx 0.1 \ m/s[/tex]
Thus, the velocity of the pitcher at the given mass is 0.1 m/s.
Learn more about conservation of linear momentum here: https://brainly.com/question/13589460
practical examples of radition
is atom on the offficial repository of ubuntu ?
Answer:
Atom, the cross-platform, open source code editor developed by Github, has become quite popular thanks to its plug-ins and embedded Git Control. ... There are, however, official Atom repositories for some Linux distributions, like Ubuntu, Debian, Fedora, Red Hat, CentOS, and open.
2. What do aerospace engineers do? (1 point)
O design dams
O design machines
O design planes
O design cars
A billiard ball with a speed of 5 m/s strikes another stationary billiard ball in a perfectly elastic collision.
After the collision, the first ball has a speed of 4.35 m/s and is traveling at an angle of 30° below its original line of motion.
Find the speed and angle of the second ball, with respect to the initial line of motion, after the collision.
Assuming both billiard balls have the same mass, conservation of momentum says
[tex]m\vec v_1 + m\vec v_2 = m{\vec v_1}\,' + m{\vec v_2}\,'[/tex]
where m = mass of both billiard balls, and v₁ and v₂ = their initial velocities, and v₁' and v₂' = their final velocities. The masses are the same so the exact value of m is irrelevant. The first ball has initial speed 5 m/s and the second is at rest, so
[tex]\left(5 \dfrac{\rm m}{\rm s}\right) \, \vec\imath = {\vec v_1}\,' + {\vec v_2}\,'[/tex]
After the collision, the first ball has speed 4.35 m/s and is moving at angle of 30° below the original path, so
[tex]{\vec v_1}\,' = \left(4.35\dfrac{\rm m}{\rm s}\right)\left(\cos(30^\circ) \, \vec\imath + \sin(30^\circ) \, \vec\jmath\right) \approx \left(3.77 \dfrac{\rm m}{\rm s}\right) \vec\imath + \left(-2.18 \dfrac{\rm m}{\rm s}\right) \vec\jmath[/tex]
Then the second ball has final velocity vector
[tex]{\vec v_2}\,' \approx \left(1.23 \dfrac{\rm m}{\rm s}\right) \vec\imath + \left(2.18 \dfrac{\rm m}{\rm s}\right) \vec\jmath[/tex]
so it moves with speed
[tex]\left\|{\vec v_2}\,'\right\| \approx \sqrt{\left(1.23\dfrac{\rm m}{\rm s}\right)^2 + \left(2.18\dfrac{\rm m}{\rm s}\right)^2} \approx \boxed{2.50 \dfrac{\rm m}{\rm s}}[/tex]
at an angle of
[tex]\theta \approx \tan^{-1}\left(\dfrac{2.18}{1.23}\right) \approx \boxed{60.5^\circ}[/tex]
or about 60.5° above the original line of motion.
What is the monthly cost of using a 750 W refrigerator that runs for 8 hours every day, if the cost per kWh is $0.23?
Answer:
Assuming there are 28 days in each month,
750W = 0.75kW
Cost of electric bill = 0.75 × 8 × 28 × $0.23
= $38.64
HEELPPPP!! A train travels 195 kilometers in 4.0 hours, and then 125 kilometers in 3.0 hours. What is its average speed?
Answer:
Train A has a speed 20 miles per hour greater than that of train B. If train A travels 300 miles in the same times train B travels 220 miles, what are the speeds of the two trains?
2. A woman has a total of $13,000 to invest. She invests part of the money in an account that pays 11% per year and the rest in an account that pays 12% per year. If the interest earned in the first year is $1490 how much did she invest in each account?
Explanation:
Describe the direction in which each object will accelerate. If the object won't accelerate, write "no acceleration." Explain what might be happening to each object in terms of its overall motion.
Answer:
No acceleration. All of the forces are acting equally on the paper air plane therfore It isn't going to move any where.
which planet should punch travel to if his goal is to weigh in at 118 lb? refer to the table of planetary masses and radii given to determine your answer.
The planet that Punch should travel to in order to weigh 118 lb is Pentune.
The given parameters:Weight of Punch on Earth = 236 lbDesired weight = 118 lbThe mass of Punch will be constant in every planet;
[tex]W = mg\\\\m = \frac{W}{g}\\\\m = \frac{236}{g}[/tex]
The acceleration due to gravity of each planet with respect to Earth is calculated by using the following relationship;
[tex]F = mg = \frac{GmM}{R^2} \\\\g = \frac{GM}{R^2}[/tex]
where;
M is the mass of Earth = 5.972 x 10²⁴ kgR is the Radius of Earth = 6,371 kmFor Planet Tehar;
[tex]g_T =\frac{G \times 2.1M}{(0.8R)^2} \\\\g_T = 3.28(\frac{GM}{R^2} )\\\\g_T = 3.28 g[/tex]
For planet Loput:
[tex]g_L =\frac{G \times 5.6M}{(1.7R)^2} \\\\g_L = 1.94(\frac{GM}{R^2} )\\\\g_L = 1.94g[/tex]
For planet Cremury:
[tex]g_C =\frac{G \times 0.36M}{(0.3R)^2} \\\\g_C = 4(\frac{GM}{R^2} )\\\\g_C = 4 g[/tex]
For Planet Suven:
[tex]g_s =\frac{G \times 12M}{(2.8R)^2} \\\\g_s = 1.53(\frac{GM}{R^2} )\\\\g_s = 1.53 g[/tex]
For Planet Pentune;
[tex]g_P =\frac{G \times 8.3 }{(4.1R)^2} \\\\g_P = 0.5(\frac{GM}{R^2} )\\\\g_P = 0.5 g[/tex]
For Planet Rams;
[tex]g_R =\frac{G \times 9.3M}{(4R)^2} \\\\g_R = 0.58(\frac{GM}{R^2} )\\\\g_R = 0.58 g[/tex]
The weight Punch on Each Planet at a constant mass is calculated as follows;
[tex]W = mg\\\\W_T = mg_T\\\\W_T = \frac{236}{g} \times 3.28g = 774.08 \ lb\\\\W_L = \frac{236}{g} \times 1.94g =457.84 \ lb\\\\ W_C = \frac{236}{g}\times 4g = 944 \ lb \\\\ W_S = \frac{236}{g} \times 1.53g = 361.08 \ lb\\\\W_P = \frac{236}{g} \times 0.5 g = 118 \ lb\\\\W_R = \frac{236}{g} \times 0.58 g = 136.88 \ lb[/tex]
Thus, the planet that Punch should travel to in order to weigh 118 lb is Pentune.
The complete question is below:
Which planet should Punch travel to if his goal is to weigh in at 118 lb? Refer to the table of planetary masses and radii given to determine your answer.
Punch Taut is a down-on-his-luck heavyweight boxer. One day, he steps on the bathroom scale and "weighs in" at 236 lb. Unhappy with his recent bouts, Punch decides to go to a different planet where he would weigh in at 118 lb so that he can compete with the bantamweights who are not allowed to exceed 118 lb. His plan is to travel to Xobing, a newly discovered star with a planetary system. Here is a table listing the planets in that system (find the image attached).
In the table, the mass and the radius of each planet are given in terms of the corresponding properties of the earth. For instance, Tehar has a mass equal to 2.1 earth masses and a radius equal to 0.80 earth radii.
Learn more about effect of gravity on weight here: https://brainly.com/question/3908593
how to find time with acceleration and velocity
Depth perception is also known as ___________ vision.
Answer:
depth from optical expansion
Explanation:
What happens to the gravity force if the mass of the planet is increased?
Answer:
The more mass an object has, the greater its gravitational field and gravity force will be.
Explanation:
gravity force = mass × gravitational field strength (g)
The more mass, the more g-force.
What is the net force on a car with a mass of 1000 kg if its
acceleration is 35 m/s^2?
Answer:
3000N
Explanation:
divided to get answer
the force needed to accelerate the 1000kg car by 3m/s2 is 3000N
A geothermal plant has been built in a location. Which of these is the most likely benefit of the geothermal plant in this location?
A. Decrease in geothermal fuels consumption
B. Improvement to hot springs and geysers
C. Long-term cost savings for energy users
D. Increase in emission of greenhouse gases
Answer:
C
Explanation:
A and B are not true and D is a disadvantage
Answer:
C. Long-term cost savings for energy users.
Explanation:
C is correct because the first option is a drawback that is unlikely. B is a good answer but not the best. It's a likely benefit, but C is a more likely benefit. D is a drawback. C is correct. I also got this right on my quiz.
Hope this helps!
a 280 nm thin film with index of refraction 1.6 floats on waterwhat is the largest wavelength of reflected light for which constructive interference occur? answer in units of m.
Answer:
Inside the film the wavelength will be λ/n
For constructive interference to occur the film must be λf/4 thick where λf is the wavelength of the light in the film - there will be a 180 degree phase shift at the water/film interface since the index of refraction of the film is greater than that of water - and the light has to travel λ/2 inside the film for constructive interference to occur
280 nm / 1.6 * 4 = 700 nm is the greatest wavelength allowed
Note that 700 nm is also the upper wavelength of the visible spectrum
State one use and one disadvantage of the expansion of materials when they are heated.
use
disadvantage
An example of the use of expansion of materials when they are heated is in
Thermometers. Thermometer is an instrument which is used to measure the
temperature of a place.
It contains mercury which expands as temperature increases. This is used
to accurately determine the temperature of an object.
The disadvantage of expansion of materials when they are heated can be
seen in roads as there is expansion of the surface as a result of heat
exposure leads to roads being rough thereby incurring more costs for
repairs.
Read more about Heat expansion on https://brainly.com/question/1166774
what role does gravity have in the motion of planets around the sun?
Answer:
The gravity helps the planets stay together near the Sun, without it Earth would be floating away with the planet eventually becoming frozen up, thus the role gravity have in the motion of planets around the sun is by keeping them together.
Explanation:
Hope this helps!
Name the force used in removing iron scrap from a heap of mixed scrap. (a) Magnetic Force (b) Electrostatic force (c) Gravitational force (d) Friction Force
Answer:
magnetic force
Explanation:
because iron is magnetic so magnet is able to attract iton
Can someone help me with this physics question? I don't know which answer is correct.
3. Distance is a quantity that is always a vector.
B.
Guys No one's answering my question so sad! Once again I'm asking the same question –Here
Chapter Name :- Vector
Question :- A car is moving at Vc speed. Rain is falling vertically at a speed of 10 m / s. What is the value of Vc in this case,if the front glass of the car will get wet? Answer :- Vc ≥ 10
Once again, I need Explanation! If you don’t know then no need to answer!
For the front glass of the car to get wet, [tex]V_c \geq 10 \ m/s[/tex].
The given parameters:
Speed of the car, = VcSpeed of the rain, = 10 m/sThe relative velocity of the car with respect to the falling rain is calculated as;
[tex]V_{C/R} = V_C- V_R[/tex]
If the speed of the car equals the speed of the rain, the rain will fall behind the car.If the speed of the rain is greater than speed of the car, the rain will fall far in front of the car.If the speed of the car is greater than speed of the rain, the rain will fall on the car.Thus, for the front glass of the car to get wet, [tex]V_c \geq 10 \ m/s[/tex].
Learn more about relative velocity here: https://brainly.com/question/17228388
which is the hottest and coldest planet in solar system ?
Answer:
hottest plant: vensus, close to the sun
coldest plant: Neptune, farthest from the sun
Explanation:
in any chemical reaction or physical change the mass of the product is ___ The mass of the reactant
a. The relationship cannot be determined by the amount of information given
b. equal to or the same
c. twice is greater than
d. twice as less than
Answer: b. equal to or the same
In Law of Conservation of mass, the mass of the product equals the mass of the reactant. A reactant is the chemical reaction of two or more elements to make a new substance, and a product is the substance that is formed as the result of a chemical reaction.
pls mark brainliest! i really need one :(
A 570 kg elevator accelerates downwards at 1.5 m/s2 for the first 13 m of its motion.
Part A
How much work is done during this part of its motion by the cable that lowering the elevator? Neglect any friction or air resistance.
Answer:
11115 J
Hope you could get an idea from here.
Doubt clarification - use comment section.