Suppose two ice hockey pucks with the same mass collide on a level, frozen pond. There is approximately no friction between the pucks and the surface.what is the change in the puck's momentum fromt t=0ms to t=100ms?

The universe is thought to be 13.8 billion years old, according to the best estimate for the Hubble constant at roughly 70 km/s/Mpc.

The Hubble constant would have to be cut in half, from 70 km/s/Mpc to 35 km/s/Mpc, increasing the assumed age of the universe.

This is so because, assuming the universe has been expanding at a constant pace since the Big Bang, & the Hubble time—which is the reciprocal of the Hubble constant—represents the age of the universe. The cosmos has been expanding for a longer time if the Hubble constant has a smaller value.

The revised Hubble constant of 35 km/s/Mpc results in a Hubble time of 28.6 billion years. This suggests that the universe is probably far older than its current estimated age of 13.8 billion years & it is also important to keep in mind that the best estimate of the Hubble constant at the time has a very low degree of uncertainty, making a significant departure from this value unlikely.

To know more about Hubble constant-

brainly.com/question/30004197

#SPJ4

The maximum current in the oscillating LC circuit is 183 mA.

In an oscillating LC circuit, the maximum charge on the capacitor and the values of inductance and capacitance are given. We can use the formula Q = CV to find the maximum voltage across the capacitor, which is V = Q/C.
V = \frac{(2.65 \mu C) }{ (4.98 \mu F) }= 0.531 V
The maximum voltage occurs when the capacitor is fully charged and the current is zero. As the capacitor discharges through the inductor, the current increases and reaches a maximum when the capacitor is fully discharged and the voltage across it is zero. The current is given by the formula I = V/L * t, where t is the time it takes for the current to reach its maximum value.
The time period of the oscillation, T, can be found using the formula[tex]T = 2\pi  \sqrt{LC)}[/tex]
T = 2\pi \sqrt(1.55 mH * 4.98 \mu F) }= 7.03 \mu s
The time it takes for the current to reach its maximum value is half the time period, t = T/2 = 3.52 μs.
Now we can calculate the maximum current:
I = V/L * t = (0.531 V) / (1.55 mH) * (3.52 μs)
I = 183 mA

learn more about current Refer:https://brainly.com/question/17176550

#SPJ11

The half-life of a decay process refers to the time it takes for half of the initial quantity of a substance undergoing decay to decay or transform into another substance. It is denoted by the symbol "t1/2" and is a characteristic property of the substance undergoing decay.

The time constant for a decay process, denoted by the symbol "τ" (tau), is a parameter that describes the rate at which a quantity decays or changes over time. It is related to the half-life by the following formula:

τ = t1/2 / ln(2)

where ln(2) is the natural logarithm of 2, which is approximately equal to 0.693.

If a decay process follows an exponential law, the relationship between the time constant and the half-life is that the time constant is equal to the half-life divided by the natural logarithm of 2. This relationship holds true for many natural decay processes, such as the radioactive decay of isotopes, decay of unstable particles, or other processes that follow an exponential decay pattern.

https://brainly.com/question/31481071

#SPJ11

The formula for angular acceleration is:
α = (ωf - ωi) / t
where α is the angular acceleration, ωi is the initial angular speed, ωf is the final angular speed, and t is the time interval.
In this case, we know that the time interval is 2.98 s, the final angular speed is 97.6 rad/s, and the initial angular speed is 0 (since the wheel starts from rest). We also know that the wheel rotates through 37.0 revolutions, which is equivalent to 2π × 37.0 = 231.2 radians.

Using the formula for angular speed :
ωf = θ / t
where θ is the angle of rotation and t is the time interval, we can find the angle of rotation:
θ = ωf × t = 97.6 rad/s × 2.98 s = 291.04 radians
Now we can plug in the values into the formula for angular acceleration:
α = (ωf - ωi) / t = (97.6 rad/s - 0) / 2.98 s = 32.77 rad/s²
Therefore, the constant angular acceleration of the wheel is 32.77 rad/s².

To learn more about Angular Acceleration & Speed : https://brainly.com/question/27343392

#SPJ11

(a) Frequency of heartbeat is 146 beats per minute or 2.43 Hz. (b) The period of heartbeat is 6.85e-3 seconds, which is the time for one cycle, and is the reciprocal of the frequency.

(a) The frequency of the heartbeat is 146 Hz. Frequency is the number of occurrences of an event per unit of time, and in this case, the event is the beating of the heart. The rate at which the heart beats is measured in beats per minute, which can be converted to Hz by dividing by 60 (the number of seconds in a minute). Therefore, the frequency of the heartbeat is 146 / 60 = 2.43 Hz.

(b) The period of the heartbeat is 6.85e-3 seconds. The period is the time it takes for one cycle of an event to occur. In this case, one cycle of the event is the heartbeat, which is the time between two consecutive beats. The period can be calculated by taking the reciprocal of the frequency, which is 1 / 146 Hz = 6.85e-3 seconds. Thus, the period of the heartbeat is the time it takes for the heart to complete one beat cycle, and it is related to the frequency of the heartbeat by the reciprocal of the frequency.

learn more about Frequency here:

https://brainly.com/question/24149245

#SPJ11

The time required for light to travel vertically from the surface of the ice to the bottom of the pond is approximately 0.0024 seconds.

To calculate this, we first need to find the distance the light has to travel through the ice and water. This can be found by subtracting the thickness of the ice from the total depth of the pond:

distance = total depth - thickness of ice
distance = 2.60 m - 0.36 m
distance = 2.24 m

Next, we can use the formula for the speed of light in a vacuum (c) and the index of refraction of water (n) to calculate the speed of light in water (v):

v = c/n
v = 3.00 x 10⁸ m/s / 1.33
v = 2.26 x 10⁸ m/s

Finally, we can divide the distance by the speed of light in water to find the time required for light to travel from the surface of the ice to the bottom of the pond:

time = distance / speed
time = 2.24 m / 2.26 x 10⁸ m/s
time = 0.0024 seconds

Therefore, it would take approximately 0.0024 seconds for light to travel vertically from the surface of the ice to the bottom of the pond.

To know more about speed of light click on below link:

https://brainly.com/question/1555553#

#SPJ11

The magnitude of the force on the 110 m section of the DC power line is 5.10 N.

The force on a current-carrying conductor in a magnetic field is given by the formula:

F = BIL sinθ

where F is the force in Newtons, B is the magnetic field strength in Tesla, I is the current in Amperes, L is the length of the conductor in meters, and theta is the angle between the direction of the current and the direction of the magnetic field.

In this case, the current is 750 A, the angle between the current and the magnetic field is 35 degrees, and the length of the conductor is 110 m. The magnetic field strength is given as 5.00 x 10^-5 T.

Substituting these values into the formula, we get:

F = (5.00 x 10⁻⁵T) * (750 A) * (110 m) * sin(35 degrees)

F = 5.10 N

Therefore, the magnitude of the force on the 110 m section of the DC power line would be 5.10 N.

To know more about DC power line

https://brainly.com/question/31391326

#SPJ4

The magnitude of the force on the 110 m section of the DC power line is 5.10 N.

The force on a current-carrying conductor in a magnetic field is given by the formula:

F = BIL sinθ

where F is the force in Newtons, B is the magnetic field strength in Tesla, I is the current in Amperes, L is the length of the conductor in meters, and theta is the angle between the direction of the current and the direction of the magnetic field.

In this case, the current is 750 A, the angle between the current and the magnetic field is 35 degrees, and the length of the conductor is 110 m. The magnetic field strength is given as 5.00 x 10^-5 T.

Substituting these values into the formula, we get:

F = (5.00 x 10⁻⁵T) * (750 A) * (110 m) * sin(35 degrees)

F = 5.10 N

Therefore, the magnitude of the force on the 110 m section of the DC power line would be 5.10 N.

To know more about DC power line

https://brainly.com/question/31391326

#SPJ4

The combination of geographic barriers, high-pressure systems, and subtropical ridges, coupled with the rain shadow effect, are the main factors responsible for the formation of Death Valley as a desert, despite its proximity to the Pacific Ocean.

The reason for the formation of Death Valley as a desert lies in its unique geographical location and topography. The surrounding mountain ranges act as barriers, preventing the moist oceanic air masses from reaching the valley. As a result, the valley experiences very little rainfall, and the air masses that do reach the valley are already dry due to the rain shadow effect.

Furthermore, the valley is located in a region with a high-pressure system, which means that the air is sinking and compressing as it descends from the surrounding mountains. As air sinks, it warms up due to adiabatic compression, resulting in high temperatures that are characteristic of deserts.

Additionally, the valley is located in an area that experiences frequent high-pressure systems and subtropical ridges, which push the moist air masses further north, away from the valley. As a result, the valley experiences very little precipitation, and the little rainfall that does occur is often short-lived and sporadic.

Learn about Death Valley here https://brainly.com/question/28605618

#SPJ1

The probability of observing a specific microstate, such as HHTHHH, depends on the system and the conditions under which it is observed. In some cases, the probability may be calculated using statistical mechanics and the principles of probability theory.

It is important to note that the probability of observing a particular microstate may be influenced by factors such as the number of particles in the system, the energy of the system, and the interactions between particles.

In summary, the probability of observing a specific microstate may be calculated using principles of probability theory and statistical mechanics, but additional information about the system and conditions may be necessary to determine the correct answer choice.

learn more about probability here: brainly.com/question/13604758

#SPJ11

The vector of the magnetic force on the particle is (350î - 50.0ĥ) N, which corresponds to option (B).

The magnetic force on a charged particle moving in a magnetic field is given by the equation F = q(v x B), where q is the charge, v is the velocity vector of the particle, and B is the magnetic field vector. Here, q = -5.00 C, v = (1.00 î + 7.00 ĥ) m/s, and B = 10.00 T along the z direction.

Taking the cross product of v and B, we get v x B = (-7.00 x 10.00) î + (1.00 x 10.00) ĥ, or (-70.00 î + 10.00 ĥ) Tm/s.

Multiplying this by the charge q, we get F = (-5.00 C) (-70.00 î + 10.00 ĥ) Tm/s, or (350.00 î - 50.00 ĥ) N.

To know more about magnetic field vector click on below link:

https://brainly.com/question/3190862#

#SPJ11

To estimate the effect at each level of copper content and temperature, a statistical analysis can be conducted using a factorial design.

This involves testing the main effects of each factor (copper content and temperature) as well as any potential interactions between them. The effect at each level of copper content can be estimated by comparing the response variable (such as yield or quality) for each level of copper content while holding the temperature constant.

Similarly, the effect at each level of temperature can be estimated by comparing the response variable for each level of temperature while holding the copper content constant. The results of the analysis can provide insight into the optimal levels of copper content and temperature for maximizing the response variable.

Learn more about the temperature at https://brainly.com/question/24746268

#SPJ11

The options a)  if it emits a photon and b) if it collides with another atom or electron are also possible ways for an excited atom to return to its ground state.

An atom can be excited if it absorbs a photon. When a photon is absorbed by an atom, it can cause an electron to jump to a higher energy level, making the atom excited. This excited state is temporary, and the electron will eventually return to its original energy level by emitting a photon or colliding with another atom or electron. The energy gained by the atom is equal to the energy of the photon that it has absorbed. The amount of energy transferred depends on the speed of the particles and the type of interaction between them.

To learn more about atom click here https://brainly.com/question/30898688

#SPJ11

The internal resistance of the battery is approximately 53.65 Ω. To find the internal resistance of the battery, we can use the formula:

Internal resistance = (emf - potential difference) / current

We know that the voltage of the battery is 5 V and the potential difference across the resistor is 3.9 V. To find the current, we can use Ohm's Law:

Current = potential difference / resistance

Resistance = 190 Ω
Potential difference = 3.9 V

Current = 3.9 V / 190 Ω
Current = 0.0205 A

Now we can substitute the values into the formula for internal resistance:

Internal resistance = (5 V - 3.9 V) / 0.0205 A
Internal resistance = 53.65 Ω.

To know more about internal resistance refer here:

https://brainly.com/question/15106247#

#SPJ11

The largest slit width for which there are no minima in the diffraction pattern is 0.0007626 meters.

The largest slit width for which there are no minima in the diffraction pattern is not infinite. In fact, if the slit width is too large, the diffraction pattern becomes indistinguishable from the pattern produced by light passing through a small aperture. The condition for the absence of minima in the diffraction pattern is given by the Rayleigh criterion, which states that the first minimum of the diffraction pattern occurs at an angle θ given by sin(θ) = 1.22λ/D, where D is the width of the slit. If there are no minima in the pattern, then sin(θ) > 0. Therefore, the largest slit width for which there are no minima is given by D = 1.22λ/sin(θ), where θ = 0. This gives D = 1.22λ, or D = 0.0007626 meters (rounded to five decimal places). Therefore, the largest slit width for which there are no minima in the diffraction pattern is 0.0007626 meters.

Learn more about diffraction :

https://brainly.com/question/12290582

#SPJ11

The total energy of a system can only change when energy is transferred to or from the system, either through work, heat, or mass exchange.

Energy can neither be created nor destroyed; it can only be transferred or converted from one form to another. Therefore, the total energy of a closed system remains constant over time, while an open system can exchange energy with its surroundings.

The principle that the total energy of a system is conserved is known as the law of conservation of energy, which is a fundamental principle in physics. It implies that any change in the energy of a system must be accounted for by an equal and opposite change in the energy of its surroundings or other systems with which it interacts.

For example, if a system gains energy through heating or work done on it, the energy of its surroundings must decrease by an equal amount to conserve the total energy of the system and its surroundings. Similarly, if a system loses energy, its surroundings must gain an equal amount of energy.

Learn more about law of conservation of energy here:

https://brainly.com/question/29775341

#SPJ11

The speed of the pulse traveling through the spring is 4.17 m/s. For part (a), the pulse will take another 1.2 seconds to return to the generator, since it must travel the same distance back.

For part (b), the pulse will cause a wave to travel through the spring. As the wave travels, the individual particles of the spring will oscillate back and forth in a repeating pattern. This motion can be described as a longitudinal wave, where the particles move parallel to the direction of the wave.

To calculate the speed of the pulse, we can use the formula: speed = distance/time. Since the pulse travels a total distance of 10.0m (5.0m to the partner and 5.0m back), and takes a total time of 2.4 seconds (1.2 seconds to the partner and 1.2 seconds back), we can plug these values into the formula to get:

speed = 10.0m/2.4s
speed = 4.17 m/s.

To know more about pulse refer here:

https://brainly.com/question/30185219#

#SPJ11

The specific heat of the metal is approximately 386 J/kg-°C.

The amount of heat required to raise a substance's temperature by one degree Celsius per gram is known as its specific heat capacity. Now that we can compare a substance's specific heat capacity per gram, we can. Its number is also influenced by the substance's phase and the type of chemical bonds present.

We can use the principle of conservation of energy,

m1c1ΔT1 = m2c2ΔT2

m1 = mass of the metal,

c1 = specific heat of the metal

ΔT1 = change in temperature of the metal

m2 = mass of the water,

c2 = specific heat of water

ΔT2 = change in temperature of the water

Substitute the values,

(0.0628 kg) c1 (175°C - 25.4°C) = (0.371 kg) (4186 J/kg-°C) (25.4°C - 23°C)

Solving for c1,

c1 = [(0.371 kg) (4186 J/kg-°C) (25.4°C - 23°C)] / [(0.0628 kg) (175°C - 25.4°C)]

≈ 386 J/kg-°C

To know more about the specific heat visit:

https://brainly.com/question/17215490

#SPJ1

The best estimate of the velocity of the skateboard immediately after the dog has jumped is 3 m/s south (option C).

The problem involves the conservation of momentum. Initially, the total momentum of the system (dog+skateboard) is zero since there is no external force acting on it. When the dog jumps off with a velocity of 1 m/s west, the total momentum of the system changes. According to the law of conservation of momentum, the total momentum of the system after the jump must also be zero.

Let v be the velocity of the skateboard immediately after the jump. Since the dog jumps off to the west, the total momentum of the system after the jump is (20 kg)(-1 m/s) + (2 kg)(v) = 0. Solving for v gives v = 10/2 = 5 m/s, which is in the south direction since the skateboard was initially traveling south. Therefore, the answer is (c) 3 m/s south, which is the closest estimate to 5 m/s.

Learn more about Mass here:

https://brainly.com/question/30337818

#SPJ11

Energy that emerges from location or configuration is known as potential energy.

Thus, According to the fundamental definition of energy as the ability to perform work, the SI unit for energy is the joule, which is equal to one newton times one meter.

Because of its location in a gravitational field, electric field, or magnetic field, an object may have the ability to do work (gravitational potential energy), electric potential energy, or magnetic potential energy.

As a result of a stretched spring or another elastic deformation, it can possess elastic potential energy.

Thus, Energy that emerges from location or configuration is known as potential energy.

Learn more about potential energy, refer to the link:

https://brainly.com/question/24284560

#SPJ12

The average force exerted by the mattresses is 1312.5 N, calculated using impulse-momentum theorem and Hooke's law.


To find the average force exerted by the mattresses on the stuntman, we can use the impulse-momentum theorem and Hooke's law.

The impulse-momentum theorem states that the impulse is equal to the change in momentum. First, find the stuntman's velocity upon impact using the conservation of energy principle.

Next, calculate the impulse, which is the product of mass and the change in velocity. Hooke's law relates the force exerted by the mattresses to their compression (F = kx).

We can find the spring constant (k) by equating the potential energy stored in the compressed mattresses to the work done against the average force.

Finally, solve for the average force exerted, which is approximately 1312.5 N.

For more such questions on impulse-momentum theorem, click on:

https://brainly.com/question/14121529

#SPJ11

Therefore, 1.61 x 10-6 is the solubility product of XY at 25 °C.

π = MRT

where the osmotic pressure is, the solute particle concentration is M, the gas constant is R, and the temperature is T in Kelvin.

To solve for the molar concentration, we can rearrange this equation as follows:

M = π / RT

A salt's molar solubility (s) and solubility product (Ksp) are connected by the following equation:

Ksp = [X][Y]

where [X] and [Y] are the ions' molar concentrations as a result of the salt XY's dissociation.

We can assume that XY entirely separates into X+ and Y- ions:

XY → X+ + Y-

As a result, the molar concentration of X+ or Y- is equal to the molar solubility of XY. If s is assumed to be XY's molar solubility, then:

[X+] = s

[Y-] = s

Since one mole of XY yields one mole of X+ and one mole of Y-, the molar concentration of XY is equal to 2s. As a result, Ksp of XY is:

[tex]Ksp = [X+][Y-]=s*s=s2[/tex]

We must first determine the molar concentration of XY using the provided osmotic pressure and temperature in order to determine the solubility product of XY:

π = MRT

[tex]RT = (28.5 torr) / (62.36 L/torr/molK * 298 K) = 0.00127 M[/tex]

The molar solubility of XY is equal to the molar concentration of X+ or Y-, which is equal to s = 0.00127 M, because XY entirely dissociates into X+ and Y- ions. Consequently, the XY solubility product is:

[tex]Ksp = s^2 = (0.00127 M)^2 = 1.61 x 10^-6[/tex]

To know more about osmotic pressure visit:

https://brainly.com/question/28727090

#SPJ1

The standard reaction free energy of the given chemical reaction is -1273 kJ/mol.

The standard reaction free energy can be calculated using the standard free energy of formation values for the reactants and products.

Reactants:

6 moles of carbon in standard state: = 0 kJ/mol

6 moles of hydrogen gas  in standard state:  = 0 kJ/mol

1 mole of oxygen gas in standard state:  = 0 kJ/mol

Products:

1 mole of glucose  in standard state: = -1273 kJ/mol

Using the equation:

[tex]ΔG°rxn = ΣΔG°f(products) - ΣΔG°f(reactants)[/tex]

we get:

[tex]ΔG°rxn[/tex] = (-1273 kJ/mol) - [6(0 kJ/mol) + 6(0 kJ/mol) + 1(0 kJ/mol)]

[tex]ΔG°rxn[/tex]= -1273 kJ/mol

learn more abouT thermodynamics here:

https://brainly.com/question/13059309

#SPJ4

A conductor carrying 15 amps enters a region of uniform magnetic field of 0.22 to. the current and the field are perpendicular. The force per unit length on the conductor in 3.3 n/m

A magnetic field is defined as the field that magnetic materials produce or as the movement of an electric charge inside a magnetic field region. To find the force per unit length on the conductor, you can use the formula:
F/L = B × I
where F is the force, L is the length, B is the magnetic field, and I is the current. In this case, the conductor carries 15 amps (I) and the magnetic field is 0.22 T (B). Since the current and magnetic field are perpendicular, you can directly apply the formula:
F/L = 0.22 T × 15 A
F/L = 3.3 N/m
So, the force per unit length on the conductor is 3.3 N/m.

Learn more about magnetic field here

https://brainly.com/question/28448786

#SPJ11

To correct the vision of a person who cannot focus on objects beyond 82.0 cm, using ordinary glasses placed 2.00 cm in front of the eye, a lens with a power of -0.61 diopters is needed.

To correct this person's vision, we need to determine the power of the lenses in her glasses. The formula for lens power is:

Power (P) = 1 / focal length (f)

The focal length needed for her glasses can be calculated using the lens formula:

1 / f = 1 / object distance (do) + 1 / image distance (di)

In this case, the person can see clearly up to 82.0 cm (0.82 m), and the glasses are 2.00 cm (0.02 m) in front of the eye. So, the image distance (di) is the sum of these two distances:

di = 0.82 m + 0.02 m = 0.84 m

Now, we can plug these values into the lens formula:

1 / f = 1 / 0.82 m + 1 / 0.84 m
1 / f = 1.2195 + 1.1905
1 / f = 2.41

Finally, we can find the focal length (f) and then the power of the lenses:

f = 1 / 2.41 ≈ 0.415 m

Power (P) = 1 / f ≈ 1 / 0.415 ≈ 2.41 diopters

The person needs glasses with lenses having a power of approximately 2.41 diopters to correct her vision.

Learn more about lenses here:

https://brainly.com/question/28025799

#SPJ11

The values of [tex]n_1[/tex] and [tex]n_2[/tex] need to relate to each other to arrive at a positive value for λ[tex]_v_a_c[/tex] .This is because it ensures that the expression [tex](1/n_1^2 - 1/n_2^2)[/tex] remains positive, leading to a positive value for the wavelength of the emitted or absorbed photon.

According to the Rydberg formula,

1/λ[tex]_v_a_c[/tex]  = R(1/[tex]n_1^2[/tex] - 1/[tex]n_2^2[/tex]),

where R = 1.097 x[tex]10^(^-^2^) nm^(^-^1^)[/tex], to arrive at a positive value for λ[tex]_v_a_c[/tex], the values of [tex]n_1[/tex] and [tex]n_2[/tex] need to relate to each other in the following manner:

Step 1: Identify the relationship between[tex]n_1[/tex] and  [tex]n_2[/tex].
Since 1/[tex]_v_a_c[/tex] is positive, the expression [tex](1/n_1^2 - 1/n_2^2)[/tex] must also be positive.

Step 2: Understand the terms in the equation.
n1 and n2 are both positive integers, and they represent the principal quantum numbers of the electron's initial (n1) and final (n2) energy levels in the hydrogen atom.

Step 3: Determine the required relationship.
For the expression [tex](1/n_1^2 - 1/n_2^2)[/tex] to be positive, it is necessary that n1 <  [tex]n_2[/tex]. This is because, as n1 becomes smaller than  [tex]n_2[/tex], the term[tex]1/n_1^2[/tex]will be larger than [tex]1/n_2^2,[/tex] making the whole expression positive.

In summary, for λ[tex]_v_a_c[/tex] to be positive in the Rydberg formula, the values of n1 and  [tex]n_2[/tex] need to relate such that n1 < [tex]n_2[/tex]. This is because it ensures that the expression [tex](1/n_1^2 - 1/n_2^2)[/tex] remains positive, leading to a positive value for the wavelength of the emitted or absorbed photon.

To know more about Wavelength refer here :

https://brainly.com/question/1598565

#SPJ11

A) According to the question, the focal length is the radius of the mirror is 3.63 m, b) Using the mirror equation, the image distance is 16.45 m, c) The magnification of the mirror is -1.98.

Radius is a network protocol used to authenticate, authorize and manage network access. It is usually used in conjunction with a Remote Authentication Dial-In User Service (RADIUS) server.

a) The mirror's focal length is given by 1/f = 1/R + 1/d, where R is the radius of curvature and d is the distance from the mirror to the object. Thus, the focal length of the mirror is f = 5.40 m/(1/5.40 + 1/8.30) = 3.63 m.

b) The image distance is the distance from the mirror to the image of the object. Using the mirror equation, the image distance is d = 5.40 m/(1/5.40 - 1/8.30) = 16.45 m.

c) The magnification is given by M = -d_i/d_o, where d_i is the image distance and d_o is the object distance. Thus, the magnification of the mirror is M = -16.45/8.30 = -1.98. This means that the image is inverted and about twice as tall as the object.

To learn more about radius

https://brainly.com/question/30145509

#SPJ1

The electric field at x=2m is 800V/m since the derivative of 200x² with respect to x is 400x, and when x=2m, Ex=400*2=800V/m.

The electric field along the x-axis can be found by taking the derivative of the electric potential function with respect to x.

Therefore, Ex at x=0m would be 0 since the derivative of any constant term (in this case, the constant term is 0) is 0. Ex at x=2m would be 800V/m since the derivative of 200x² with respect to x is 400x and when x=2m, Ex=400*2=800V/m.

The electric potential is a measure of the electric potential energy per unit charge at a given point in space. It is a scalar quantity and is related to the electric field, a vector quantity, by a gradient relationship.

The electric field is the negative gradient of the electric potential, which means that the electric field is the rate at which the potential changes per unit distance in a particular direction.

In this case, the electric potential along the x-axis is given as V=200x², and the electric field can be found by taking the derivative of this function with respect to x. The electric field at x=0m is zero since the derivative of any constant term is zero.

To know more about derivative click on below link:

https://brainly.com/question/25324584#

#SPJ11

The correct ranking of the speeds of the balls as they reach the ground, from fastest to slowest, is 3 > 1 > 2.

This can be explained by the fact that the initial horizontal velocity of the first ball (ball 1) remains constant throughout its motion, while the other two balls (ball 2 and ball 3) have initial velocities that have both horizontal and vertical components.

When ball 2 is thrown above the horizontal, its initial vertical component of velocity works against its motion and it takes longer to reach the ground compared to ball 1. When ball 3 is thrown below the horizontal, its initial vertical component of velocity works with its motion and it reaches the ground sooner than ball 2, but still slower than ball 1.

Since all three balls have the same initial speed and neglect air resistance, the ball that takes the shortest time to reach the ground will have the highest speed when it reaches the ground.

Therefore, ball 3 has the highest speed, followed by ball 1 and then ball 2.

to know more about speed refer here:

https://brainly.com/question/28224010#

#SPJ11

Answer:

C.

As the temperature increases, the speed of gas molecules increases.

(a) The relationship between true stress (σ) and true strain (ε) can be written as: σ = kε[tex]^n[/tex]

Taking the natural logarithm of both sides:

ln(σ) = n ln(ε) + ln(k)

This equation has the form of a linear equation y = mx + b, where y = ln(σ), x = ln(ε), m = n, and b = ln(k). Thus, we can plot ln(σ) vs. ln(ε) and find the slope of the line to determine the value of n and the intercept to determine the value of k.

Using k = 500 MPa and n = 0.25, we can find the slope and intercept as:

slope (n) = 0.25

intercept (ln(k)) = ln(500 MPa) = 6.2146

The slope of the line is related to the Young's modulus (E) through the following equation:

E = σ/ε = n σ/ε = n slope

Thus, the Young's modulus for this material is:

E = n slope = 0.25 * 1 = 0.25 MPa^-1

(b) The 0.2% yield strength (σ_y) is the stress at which the material exhibits a permanent strain of 0.2%. We can find this by setting ε = 0.002 in the power law equation and solving for σ:

σ_y = kε[tex]^n[/tex] = 500 MPa * (0.002)[tex]^0.25[/tex] = 288.8 MPa

Therefore, the 0.2% yield strength of the material is 288.8 MPa.

(c) The resilience of a material is the amount of energy per unit volume that can be absorbed without causing permanent deformation. It is given by the area under the stress-strain curve up to the yield point. Since we have an equation for the true stress-strain curve, we can integrate it from ε = 0 to ε_y, where ε_y is the strain at the yield point. We can find ε_y by rearranging the power law equation to solve for ε:

ε = (σ/k)[tex]^(1/n)[/tex]

Now we can integrate the true stress-strain equation from ε = 0 to ε_y to find the resilience:

[tex]R = ∫₀^ε_y σ dε = ∫₀^ε_y kε^n dε\\\\= k/(n+1) ε_y^(n+1)[/tex]

= 500 MPa / (0.25+1) * (0.0388)^(0.25+1)

= 3.14 MPa

Therefore, the resilience of the material is 3.14 MPa.

To know more about stress here

https://brainly.com/question/11819849

#SPJ4