The the velocity which the water flow out of the tank is 29.698 m/s
What is Bernoulli's principle?
It gives the relationship between pressure, kinetic energy, and gravitational potential energy of a fluid in a container .
P₁ + 1/2ρv₁² + ρgh₁ = P₂ + 1/2ρv₂² + ρgh₂
Since it is a open tank,
P₁ = P₂ = P₀ , atmoshperic pressure
h₁ = 50m
h₂ = 5m
v₁ = 0
Applying Bernoulli's principle
P₁ + 1/2ρv₁² + ρgh₁ = P₂ + 1/2ρv₂² + ρgh₂
P₀ + 0 + ρgh₁ = P₀ + 1/2ρv₂² + ρgh₂
ρgh₁ = 1/2ρv₂² + ρgh₂
v₂ = √(2g(h₁-h₂))
= √(2×9.8(50-5))
= 29.698 m/s
Therefore the velocity which the water flow out of the tank is 29.698 m/s
To learn more about Bernoulli's principle below is the given link:
https://brainly.com/question/1158726
#SPJ4
a 500 w heating unit is designed to operate with an applied potential difference of 115v. by what percentage will the power drop if the applied potential difference is reduced to 100v?
We change [V 1] to 115 V, [V 2] to 110 V, and [P 1] to 500 W in the equation above. As a result, the output power will decline by 8.5%, which will also result in an 8.5% fall in heating output.
How much heat is produced by 500W?A low-wattage 500W heater can effectively heat places up to 57 square feet and offers a heating output of 1706 BTU. The smallest 200W heater, which can heat places up to 23 square feet, has a heating output of 682 BTU.
How much energy does an electric heater use?Since they convert all of the electricity they consume into heat, electric heaters are all believed to be 100% efficient, but this does not imply that their operating costs are low.
To know more about potential difference visit:-
https://brainly.com/question/12198573
#SPJ4
a toy cannon is fixed to a small cart and both move to the right with speed v along a straight track, as shown above. the cannon points in the direction of motion. when the cannon fires a projectile the cart and cannon are brought to rest. if m is the mass of the cart and cannon combined without the projectile, and m is the mass of the projectile, what is the speed of the projectile relative to the ground immediately after it is fired?
The speed of the projectile relative to the ground immediately after it is fired is determined as v.
What is the final speed of the projectile?The final speed of the projectile is obtained by applying the principle of conservation of linear momentum.
The law of conservation of linear momentum states that in an isolated system, the sum of the initial momentum is equal to the sum of the final momentum.
Pi = Pf
where;
Pi is initial momentum of the cannon and small cartPf is the final momentum of the projectilePi = mv
where;
m is the mass of the toy cannon and small cart combined v is the speed of the toy cannon and small cart combinedPf = Pi = mv
since mass of the projectile = m
The final speed is calculated as;
Pf = mv
v = Pf / m
v = mv / m
v = v
Learn more about speed of projectile here: https://brainly.com/question/24097127
#SPJ1
What is the mathematical relationship between the velocity of the sound v its wavelength λ and its frequency f?
The mathematical relationship between the velocity of sound, its wavelength, and its frequency is represented by the equation v = fλ, where v is the velocity of the sound, f is the frequency of the sound, and λ is the wavelength of the sound.
What is velocity?Velocity is a measure of how quickly something is moving in a given direction. It is a vector quantity, meaning it has both magnitude and direction. Velocity is typically expressed in units of distance per unit of time, such as meters per second (m/s). Velocity is a measure of how quickly an object is changing its position relative to its surroundings.
This equation is known as the wave equation and is a fundamental concept in physics. It states that the velocity of a wave is equal to the product of its frequency and wavelength.
To know more about velocity click-
https://brainly.com/question/24445340
#SPJ4
What are the 4 types of diseases with examples?
Infectious diseases, deficient diseases, hereditary diseases (covering both genetic disorders and non-genetic hereditary diseases), and physiological diseases are the four primary categories of disease.
Give examples of the different diseases.Asthma. Chronic pulmonary condition known as asthma is characterized by episodes of airway blockage and narrowing that result in wheezing, coughing, chest tightness, and shortness of breath. Autoimmune Conditions. ALPS, or Autoimmune Lymphoproliferative Syndrome Cholera. Coronaviruses. The dengue virus.
Which five diseases are they?Each year, infectious diseases afflict billions of individuals worldwide. These infectious diseases are the five most prevalent, say the WHO and CDC. Infectious diseases are illnesses brought on by pathogens—dangerous organisms—that enter your body from the outside.
To know more about types of diseases visit:-
https://brainly.com/question/8611708
#SPJ4
two people are pulling on the ends of a rope. each person pulls with a force of 100 n. the tension in the rop is:
Option C 100 N is correct. Given that no element of the system is in motion, a person pulling with 100 N of force at either end of the rope is met with a 100 N tension in the rope.
Because the rope is subjected to the same pulling force on both sides, it is in a state of static equilibrium (i.e. it is at rest consequently has a net force of zero). Tension on a rope will be zero if it is pulled from its ends by two opposing forces of 100N each since both forces have identical magnitude but operate in different directions on the same body and cancel each other out.
The complete question is- Two people are pulling on the ends of a rope. Each person pulls with a force of 100 N. The tension in the rope is:
A 0 N
B 50 N
C 100 N
D 141 N
E 200 N
Learn more about force here-
https://brainly.com/question/13191643
#SPJ4
help me plsplsplsplsplsplsplspls
Answer:2.15 (rounded to 2 decimal place)
Explanation:Mass = 28g
Volume =?
Density = 13 g/ml
Volume = Mass/Density
Volume = 28/13
volume= 2.15384615
classify each of the following amines as primary (1∘), secondary (2∘), or tertiary (3∘):
Amine classification: Primary, Secondary Amines, which are derivatives of ammonia, are categorized as primary (1°), secondary (2°), and tertiary (3°) based on how many hydrogen atoms in the ammonia molecule have been replaced by alkyl or aryl groups.
A primary amine is created when one alkyl group replaces one hydrogen atom in NH 3. primary, secondary, tertiary, or quaternary amine as 1o, 2o, 3o, or 4° (CH3)4N+ .
(C₂H₅)CHNH₂ N atom is directly connected with only one C atom (i.e. one alkyl group) So, it is a primary amine.
An intermolecular interaction involves primary and secondary amines. This is because the nitrogen in one molecule and the hydrogen in another molecule form a hydrogen bond. This intermolecular interaction is more prevalent in primary amines compared to secondary amines.
To know more about Amine
https://brainly.com/question/29076299
#SPJ4
What is the name of the electrical component used to measure the current in a circuit?
Ammeter is the name of the electrical component used to measure the current in a circuit.
What is ammeter?An instrument used to measure the current in a circuit is called an ammeter, which is short for ampere meter. Amperes (A) are units used to measure electric currents. The circuit in which the current is to be measured and the ammeter are linked in series to allow for direct measurement. A typical ammeter has a low resistance so that it won't significantly lower the voltage in the circuit being measured.Microammeters and milliammeters are terms used to describe devices that measure currents in the milliampere or microampere range. The Earth's magnetic field was necessary for the operation of the earliest ammeters, which were laboratory instruments. Improved instruments were created by the late 19th century that could be put in any orientation and permitted precise measurements in electric power systems. It is generally represented by letter 'A' in a circuit.For more information on ammeter kindly visit to
https://brainly.com/question/22787866
#SPJ4
T/F observations in the x-ray portion of the spectrum are routinely done from the surface of the earth.
Observations in the X-ray portion of the spectrum are routinely done from the surface of the Earth is a false statement .
The electromagnetic spectrum's infrared region is where the earth emits the most energy. When the energy from the sun reaches the surface of the Earth, 49.4% of it is infrared radiation, 42.3% of it is visible light, and 8.3% of it is ultraviolet radiation.After being received from the sun, energy is reflected back into the atmosphere ( in the form of light ). The energy radiated by the Earth is significantly weaker than the Sun because it is much cooler. As a result, it emits infrared radiation ( long wavelength )As a result, the planet emits the most energy in the infrared region of the electromagnetic spectrum is correct statement .
To know more about X-ray portion
https://brainly.com/question/20432333
#SPJ4
How do you calculate the speed of emitted photoelectrons?
The formula to calculate speed of emitted photoelectron is KE = 1/2mv²
What is Photoelectric effect?The process through which electrons leave a metal's surface after absorbing electromagnetic radiation is known as the photoelectric effect.
Since photons are the units of light, according to Einstein's theory, when a photon collides with a metal's surface, the full photon's energy is transferred to the electron. A portion of this energy is utilized to free the electron from the metal atom's hold, while the remainder is transferred as kinetic energy to the ejected electron.
Three crucial aspects of the photoelectric effect are not explicable by classical physics: (1) the lack of a lag time; (2) the independence of the photoelectrons' kinetic energy from the strength of the incident radiation; and (3) the presence of a cut-off frequency.
To learn more about Photoelectrons from given link
https://brainly.com/question/30007912
#SPJ4
Q4. State the energy transformations in the following cases.
a) electric iron __________ to __________
b) in lighting a candle ________ to _______
c) battery ___________ to ____________
d) boiling water on a gas hob _____ to ____
ezrah attached a baseball to a small rope that is 0.50 meters in length. He then began spinning the string with rotational speed of 2.0 rotations per second. predict how to tangential velocity of the ball would change if ezrah reduced the length of the rope to 0.25 meters and rotational speed is help constant
if Ezra reduced the length of the rope to 0.25 meters and rotational speed is held constant, There is a change of 3.14 m/sec in the velocity when length of rope is reduced from 0.50 to 0.25 m.
What is rotational speed?The no. of revolutions made by a rotating object in a given defined time is termed as rotational speed.
Solution:
Given:
initially length of rope i.e. R = 0.50m
2 rotations per second = 1 rotation =0.5 sec= T
now after changing ropes length R=0.25 m
Initially velocity of the ball rotating on R =0.50m
⇒v=2πR/T
⇒v=2*3.14*0.50/0.5
⇒v=6.28 m/sec
6.28 m/sec is the velocity of the ball rotating on R =0.50m.
Now to find the velocity of the ball rotating on R =0.25m we use the following eq.
⇒v=2πR/T
⇒v=2*3.14*0.25/0.5
⇒v=3.14 m/sec
3.14 m/sec is the velocity of the ball rotating on R =0.25m
Hence, there is a change of 3.14 m/sec in the velocity when length of rope is reduced from 0.50 to 0.25 m.
To know more about rotational speed visit
https://brainly.com/question/17025846
#SPJ1
a 7500 kg rocket blasts off vertically from the launch pad with a constant upward acceleration of 2.25 m>s and feels no appreciable air resistance. when it has reached a height of 525 m, its engines suddenly fail; the only force act- ing on it is now gravity. (a) what is the maximum height this rocket will reach above the launc
2=2×9.8(48.6)2=121mThe maximum displacement above pad is given by '
ymax=y1+y2=525+121=646 m The velocity just before crashing is given by vA22=vC2+2gymax ⇒(3) By substitution in (2) get that vA2=2×9.8×646≈113 m/s vA2=2×9.8×646 ≈113m/s the maximum height this rocket will reach above the launc is ymax=646M.
What is subject to the effects of gravity?Whether an object is moving or not, gravity still exerts a pull on it.In real life, an object's gravitational pull does not vary considerably when it ascends above the Earth.
when only gravity is exerting a force on it?An object is considered to be in terminal decline when gravity is the only force affecting it.9.8 m/s is the acceleration caused by gravity.
To know more about force visit:
https://brainly.com/question/13191643
#SPJ4
How long will it take for a radioactive sample to decrease to 25% if its half-life is 11 years?
If the half-life of a radioactive sample is 11 years, it will take 37.06 years for the sample to decay to 25%.
What number of half lives have passed if there is 25% radioactivity left?Cobalt-60 has a half-life of 5.27 years, meaning that 50% of it is still present after that time (one half-life), 25% is still present after that time (two half-lives), 12.5% is still present after that time (three half-lives), and so on.
How long will it take 131 I sample to decay by 50%?Iodine-131, for instance, is a radioisotope with an 8-day half-life. By emitting beta particles, it decomposes into xenon-131. Any sample of iodine-131 will have half of its atoms destroyed after eight days.
To know more about radioactive sample visit:-
https://brainly.com/question/9674119
#SPJ4
What are the benefits of wind and solar?
As they lessen reliance on combustion-based electricity generation, wind and solar energy boost air quality, public health, and greenhouse gas emissions.
What are three advantages of solar energy?Solar energy has advantages as a renewable energy source. The fact that solar energy is a completely renewable energy source is the most significant of all the advantages of solar panels. Reduces electricity costs and has many uses. Costs of maintenance are low.
What advantages do solar panels offer?A clean, emission-free, and sustainable energy source is home solar power. Home solar energy, as opposed to fossil fuels like coal and natural gas, doesn't emit hazardous pollutants or greenhouse gases like carbon dioxide into the air and water supplies.
To know more about benefits of wind and solar visit :-
https://brainly.com/question/29234403
#SPJ4
The velocity of a body change from vi to 30m/in 20econd if the rate of change of velocity i 4m/2 find vi
The velocity of a body change from vi to 30m/s in 20econd if the rate of change of velocity is 4m/s, initial velocity is -50 m/s.
To find the initial velocity, vi, of a body that undergoes a change in velocity, you can use the formula:
vi = vf - at
where vi is the initial velocity, vf is the final velocity, a is the acceleration (rate of change of velocity), and t is the time over which the acceleration occurs.
In this case, you are given that the final velocity is 30 m/s, the acceleration is 4 m/s^2, and the time is 20 seconds. Plugging these values into the formula gives:
vi = 30 m/s - 4 m/s^2 * 20 s
vi = 30 m/s - 80 m/s
vi = -50 m/s
Therefore, the initial velocity of the body is -50 m/s.
To know more about velocity
https://brainly.com/question/28738284
#SPJ4
Which sectors have the highest Scope 3 emissions?
Burning fossil fuels for transportation, heat, and power is the main cause of human-related greenhouse gas emissions in the United States.
What are the top three emissions sources?Notes. About 76 percent of all greenhouse gas emissions are made up of CO2. Methane, which is mostly produced by agriculture, accounts for 16% of greenhouse gas emissions, while nitrous oxide, which is primarily produced by industry and agriculture, accounts for 6% of total emissions.
What does oil and gas scope 3 entail?Indirect emissions from the production of purchased energy are considered scope emissions. All indirect emissions that occur upstream and downstream in the reporting company's value chain and are not covered by scope 2 are referred to as scope 3 emissions. 2.
To know more about scope emissions visit:-
https://brainly.com/question/29546969
#SPJ4
the equipment you have to use is a force sensor, multiple carts, multiple masses, multiple springs, a track and some clamps. by putting the cart in motion and observing the oscillation we can see the reduction in amplitude over time and use that to model the decaying amplitude. that model will allow us to evaluate b for the oscillation. our guided question is: is the damping coefficient of a spring-cart system independent of mass?
Yes, the damping coefficient of a spring-cart system independent of mass. Mass doesn't affect the damping coefficient (since that is assumed constant).
Damping coefficient - The system’s damping coefficient is a measure of how quickly it returns to rest as the frictional force dissipates its oscillation energy.
Damping is experienced by most oscillatory systems such as harmonic oscillators. These systems, when displaced from their equilibrium position, experience a restoring force proportional to their displacement. If a frictional force proportional to the velocity is also applied, the system exhibits damped harmonic oscillation. In a damping phenomenon, the amplitude of the oscillation is decreasing gradually instead of sudden decreasing. When there is a damping in the system then the amplitude decreases and the period increases.
So, We can see that mass will absolutely affect the damping ratio, but not the damping coefficient (since that is assumed constant).
learn more about Damping coefficient:
https://brainly.com/question/20115234
#SPJ4
How many Scope 3 categories are there?
The majority of an organization's overall greenhouse gas (GHG) emissions frequently come from scope 3 emissions, also known as value chain emissions. Scope 3 emissions are divided into 15 categories by the GHG Protocol.
A Scope 3 analysis is what is it?Greenhouse gas emissions from a corporation that it directly manages. indirect greenhouse gas emissions caused by the electricity or other energy a corporation utilizes. indirect greenhouse gas emissions of a firm that are not covered by Scope 2.
What makes Scope 3 crucial?In many industries (and more than 90% in many global corporations, according to CDP reporting), scope 3 emissions, also known as "Value Chain emissions," make up the bulk of total emissions. These emissions are regarded as essential to combating climate change.
To know more about scope 3 emissions visit:-
https://brainly.com/question/29546969
#SPJ4
Which of the following actions, if done independently; would increase the maximum height reached by the ball?
a. reducing the spring constant k
b. increasing the spring constant k
c. decreasing the distante the spring is compressed
d. increasing the distance the spring is compressed
e. decreasing the mass of the ball
Increasing the spring constant k, increasing the distance the spring is compressed, decreasing the mass of the ball will increase the maximum height reached by the ball.
What is meant by maximum height reached by the object?
An object thrown vertically up will rise to its maximum height in direct proportion to its initial velocity, u.
First, as compression distance and spring constant k are raised while mass is decreased, maximum height will increase. As a result, we can select the best course of action by first raising the spring constant. Next, we have the option of extending the distance. Lastly, the spring is compressed, reducing the ball's bulk.
To learn more about the maximum height of the object from the given link
https://brainly.com/question/13665920
#SPJ1
What is the meaning of primordial heat?
Answer:
The primordial heat of a planet is the heat caused by the dissipation of heat energy accumulated during its first few million years. Accretion energy is the energy deposited by infalling planetesimals and differentiation energy is the energy deposited by separating planetesimals.
When an object of ma m1 i hung on a vertical pring and et into vertical imple harmonic motion, it
ocillate at a frequency of 12. 0 Hz. When another object of ma m2 i hung on the pring along with the
firt object, the frequency of the motion i 4. 00 Hz. Find the ratio m2 /m1 of the mae
The ratio of the mass of the objects which are hung in the vertical spring is 9
The frequency of the spring with mass m₁ = 12 Hz
The frequency of the spring with the mass m₂ = 4 Hz
The ratio of the mass can be found using the formula,
[tex]\displaystyle f = \frac{1}{2 \pi} \sqrt{\frac{k}{m} }[/tex]
where f is the frequency of the spring
k is the spring constant
m is the mass
Then, the ratio of masses is
m₂ / m₁ = f₁² / f₂²
Let us substitute the known values in the above equation, we get
m₂/m₁ = 12² / 4²
= 144 / 16
= 9
Therefore, the ratio of mass is 9
Learn more about the frequency in
https://brainly.com/question/30031128
#SPJ4
a force of 40Nis applied at the end of a wire 4m long and produces an extension of 0.24mm. if the diameter of the wire is 2.0mm. calculate the stress and strain of the wire
Answer:
stress = 13000000 N/m or Pa
Strain = 6x10^-5
Explanation:
Radius - d/2
Radius = 2 /2
Radius = 1 mm
Stress = F/A
stress = F / (πr^2)
Stress = 40 / (π(1 / 1000)^2)
Stress = 12732395 ≈ 13000000 N/m or Pa
Strain = Extension / Original length
Strain = (0.24 / 1000) / 4
Strain = 6x10^-5
I hope my answer helps you.
What are 2 literary devices we see in satire?
The 2 literary devices we see in satire are:
Irony: Gap between what is said and what is meant.
Hyperbole: A literary term for exaggerating a particular event or person.
What is satire?
Satire is a genre of visual, literary, and performing arts, usually fiction, rarely non-fiction, is intended to embarrass or disclose Improve a company, government, or society itself. Although satire is usually intended to be humorous, its more important purpose is often constructive social criticism, drawing witty attention to specific and broader societal issues.
The hallmark of satire is strong sarcasm and irony - according to literary critic Northrop Fry, "in satire sarcasm is warlike" - but parody, burlesque, exaggeration, juxtaposition, comparison, Analogies, double entenders, are all commonly used in satirical speaking and writing. This "belligerent" cynicism and cynicism often professes to condone (or at least take for granted) exactly what the satirist wants to question.
The 2 literary devices we see in satire are:
Irony: Gap between what is said and what is meant.
Hyperbole: A literary term for exaggerating a particular event or person.
To know more about Satire, visit:
https://brainly.com/question/4230795
#SPJ4
Which objects cannot be observed in detail without a microscope? choose more than one answer.
Virus
Explanation:
Virus is 20 to 100 times smaller than bacteria
Bacteria are larger than virus
What are the 7 types of electromagnetic waves from left to right?
Radio waves, microwaves, infared waves, visible light, ultra-violet, x-Rays and gamma rays are the 7 types of electromagnetic waves from left to right.
The electromagnetic spectrum's longest wavelengths are found in radio waves, a kind of electromagnetic radiation.
Wavelengths of electromagnetic radiation, which include microwaves, typically range from one meter to one millimeter.
Longer wavelengths than visible light characterize infrared electromagnetic energy, also referred to as infrared light.
The area of the electromagnetic spectrum that is visible to the human eye is referred to as the visible spectrum.
A type of electromagnetic radiation with a shorter wavelength than visible light is ultraviolet radiation (UV).
A penetrating kind of high-energy electromagnetic radiation is an X-ray or, much less frequently, an X-radiation.
Sharp electromagnetic radiation waves called gamma rays, also referred to as gamma radiation, are created when atomic nuclei break down radioactively.
For more information on electromagnetic waves kindly visit to
https://brainly.com/question/3101711
#SPJ4
What type of friction is sliding?
Sliding friction, also known as kinetic friction, is indeed a contacting force that opposes the motion of two items sliding against one another or between a body and a substrate.
How can kinetic friction be determined?
Ff=kFN F f = k F N, where k is the multiplier of frictional force and FN is the object's normal force, is the equation for kinetic friction.
Which four forms of kinetic friction are there?
The force that prevents one solid item from moving across another is known as friction. Surface tension, sliding friction, rolled tension, and fluid friction are the four main categories of friction.
To know more about kinetic friction visit :
https://brainly.com/question/13828735
#SPJ4
just as a traffic light turns green, a waiting car starts off with a constant acceleration of 6.0 m/s2 . at the instant the car begins to accelerate, a truck with a constant velocity of 21 m/s passes in the next lane. (a) how far will the car travel before it overtakes the truck? (b) how fast will the car be traveling when it overtakes the truck?
(a) The car travels a distance of 147 m before it overtakes the truck.
(b) At the moment when car overtakes the truck, the speed of car was 21 m/s
Let us assume that the time taken by the car to overtake the truck = t seconds
Now calculating the distance travelled by car and truck during this time,
Using the kinematic equation for calculating the distance travelled by car and the truck:
The distance travelled can be computed by the relationship [tex]s= 0.5at^2[/tex]
Distance travelled by car will be [tex]S_{car} =0.5 \times 6\times t^2=3t^2 \:m[/tex]
Distance travelled by truck will be [tex]S_{truck}=21 \times t = 21t \:m[/tex]
At the instant of overtaking
Distance travelled by car = Distance travelled by truck
[tex]3t^2 = 21t\Rightarrow t = \frac{21t}{3t}=7\:sec.[/tex]
So, the distance travelled by car before it overtakes will be 3*7*7 = 147 m
(b) As Car have crossed the truck in 7 sec. after covering a distance of 147 m.
So, at the moment of overtaking the truck the speed of the car will be = 147/7 = 21/s
For more questions on kinematic equation
https://brainly.com/question/28788270
#SPJ4
Mr. Chang's class participated in a science experiment where they placed three substances outside in the sunlight to determine which substance would increase in temperature more quickly. How would the motion of the particles of each substance be described if they are allowed to sit in the sun for a duration of 10 minutes?.
In order to find out which substance would raise in temperature most quickly, Mr. Chang's class conducted a scientific experiment outside in the sunlight using three different substances.
If particles of each substance were permitted to sit in the sun for 10 minutes, how would their motion be described? B. Physical alterations are non-chemical changes that are made to an item or substance. They alter an object's physical characteristics, such as its size, color, texture, volume, or density. To find out more about the science underlying the treat or to find some more at-home experiments, see the resources listed below. Just keep in mind that science is best when it is shared, so tell your friends about your experiment.
To learn more about temperature please click on below link
https://brainly.com/question/11464844
#SPJ4
Is gravitational potential energy a renewable or non-renewable?
Answer:
It is renewable.
Explanation:
The gravity of the earth is infinite and so it is renewable energy.
Gravitational potential energy is neither renewable nor non-renewable as it is a form of energy that exists due to the position of an object in a gravitational field. It is a type of potential energy that is associated with an object's position in a gravitational field and its mass. The amount of gravitational potential energy an object has depends on its mass, height above the reference level, and the strength of the gravitational field.
What is renewable or non renewable energy ?Renewable and non-renewable energy sources refer to the sources of energy that are used to generate electricity or power and are consumed over time. Examples of renewable energy sources include solar, wind, and hydropower, while non-renewable energy sources include fossil fuels such as coal, oil, and natural gas.
Therefore, gravitational potential energy is not considered a renewable or non-renewable energy source as it is not a source of energy that is harvested or consumed. Rather, it is a property of an object that can be converted into other forms of energy such as kinetic energy when the object falls or is released from its position in a gravitational field.
To know more about Energy ;
https://brainly.com/question/1932868
#SPJ2.