Help meeee is for tomorrow, plssss!!!
2) For the association of resistors below:
a) The equivalent resistor between A and B.
b) The total electric current that runs through the circuit, knowing that the electrical voltage between terminals A and B is valid 21 V(volts).
c) The value of the electric current passing through the resistor of 1.0 Ohm.
d) The power dissipated through the 8.0 Ohm resistor.
Answers
(a) The equivalent resistance of the circuit is 0.52 ohms.
(b) The total electric current that runs through the circuit is 40.38 A.
(c) The value of the electric current passing through the resistor of 1.0 Ohm is 21 A.
(d) The power dissipated through the 8.0 Ohm resistor is 55.13 W.
Equivalent resistance of the circuitThe equivalent resistance of the circuit is calculated as follows;
1/R = 1/(1 + 1) + 1/(2 + 2 + 2) + 1/(6) + 1/(2) + 1/8 + 1/8 + 1/6 + 1/6
1/R = 1/2 + 1/6 + 1/6 + 1/2 + 1/8 + 1/8 + 1/6 + 1/6
1/R = 1 + 2/3 + 1/4
1/R = 23/12
R = 12/23
R = 0.52 ohms
Total current through the circuitV = IR
I = V/R
I = 21/0.52
I = 40.38 A
Current through 1 ohm resistorV = IR
I = V/R
I = 21/1
I = 21 A
Power dissipated through 8 ohm resistorP = V²/R
P = (21)²/8
P = 55.13 W
Learn more about power dissipated here: https://brainly.com/question/20642331
#SPJ1
Related Questions
Why is it not possible to achieve a higher resolution in the light microscope?.
Answers
Explanation:
Because resolution of the light microscope cannot be small than the half of the wavelength of the visible light
-1 A 4m long wire of cross-sectional area 2.5 X 10 m² has a resistance of 5. The conductivity of the wire is (a) 2.5 X 10' m (b) 4.0 X 10' m (c) 2.5 X 10'' m¹ -1 -1 (d) 4.0 X 10''m'
Answers
Answer:
3.2 [tex]10^{-2} ohm^{-1} m^{-1}[/tex]
Explanation:
Resistance=5 ohm
Length=4m
Cross sectional area=2.5 x 10
Conductivity = 1/ resistivity
=[tex]\frac{length}{resistance x cross sectional area}[/tex]
Conductivity=4 /5 x 2.5 x 10
Conductivity=4/125
Conductivity=3.2x[tex]10^{-2}[/tex][tex]ohm^{-1} m^{-1}[/tex]
A cue ball of inertia m is given a speed v before it collides elastically with a full rack of 15 stationary balls in a game of pool. Each of the 16 balls has an inertia m.
Answers
The final speed of the 15 stationary balls in a game of pool is determined as the ratio of inertia of the cue ball to total mass of the 15 balls.
Final speed of the 15 balls
The final speed of the 15 balls can be determined by applying the principle of conservation of linear momentum as shown below;
J = ΔP
where;
J is inertia ΔP is change in momentumm1u1 + m0u0 = m1v1 + m0v0
where;
m1 is mass of the cue ballm0 is mass of the 15 ballsu is initial velocityv is final velocitym1u1 - 0 = m1v1 + 15mv0
m1u1 - m1v1 = 15mv0 - 0
recall, m1u1 - m1v1 = ΔP = J
-m = 15m0v0
v0 = -m/15m0
where;
v0 is the final speed of the 15 balls15m0 is the total mass of the 15 ballsm is the inertia of the cue ballThus, the final speed of the 15 stationary balls in a game of pool is determined as the ratio of inertia of the cue ball to total mass of the 15 balls.
Learn more about linear momentum here: https://brainly.com/question/7538238
#SPJ1
describe one example of how a person's religious faith associated with a world religion can be seen in an incident from their life.
Answers
Answer:
The Crusades, the many periods of persecution of Jews, religious conflicts between Catholics and Protestants in sixteenth- and seventeenth-century Europe, the execution of hundreds of Christians in seventeenth-century Japan, the Mormon expulsion from Missouri and Illinois in the 1840s, the Branch Davidian conflagration
Nina and ryan each ran at a constant speed for a 100-meter race. Each runner’s distance for the same section of the race is displayed on the left. Who had a head start, and how big was the head start?.
Answers
"Nina and Ryan each ran at a constant speed for a 100-meter race. Each runner’s distance for the same section of the race is displayed on the left." In the event of things, Ryan had a headstart of 10min. This is further explained below.
What is headstart?Generally, headstart is simply defined as a head start is a benefit received or awarded from the outset.
In conclusion, "When racing 100 meters, both Nina and Ryan maintained a steady pace. On the left is a chart showing the distance covered by each runner during the same segment of the race." Whatever the case may be, Ryan was given a 10-minute head start.
Read more about headstart
https://brainly.com/question/14538145
#SPJ1
Answer: Ryan had a head start of 10 meters.
Explanation: Trust me
A 84-kg man stands on a bathroom scale inside an elevator. the scale measures in units of newtons. (a) the elevator accelerates upward from rest at a rate of 1.20 m/s2 for 1.50 s. what does the scale read during this 1.50 s interval
Answers
Answer:
94 kg
Explanation:
The mass registered by the scale is based on the assumption that the force applied is due entirely to gravity. If the force is greater, then the indicated mass will be greater.
__
how many g'sAs a fraction of the acceleration of gravity, the elevator's acceleration is ...
(1.2 m/s²)/(9.8 m/s²) ≈ 6/49
net forceThe force required to produce a given acceleration is found by the formula ...
F = ma . . . . . . . force on mass m to produce acceleration 'a'
When the man is stationary on the scale, the upward force it supplies is balanced by the downward force on the man due to gravity. The force and the mass are proportional, and the constant of proportionality (the acceleration due to gravity) is used to calibrate the scale. More force is thus translated to a higher mass reading.
Since the man's net acceleration is upward at the rate of 6/49×g, the total force applied by the scale is (1 +6/49) = 55/49 times as great as when the man is stationary. This greater force gets translated to a greater mass reading.
The force is equivalent to what would be required to support a stationary man with a mass of ...
(84 kg)(55/49) = 94 2/7 kg
The scale would read about 94 kg during the upward acceleration period.
Which labels belong in the regions marked X, Y, and Z?
OX: Smaller nuclei form
Y: Thermal energy is produced
Z: A larger nucleus forms
OX: Large amounts of energy are released
Y: One or more neutrons is released
Z: Smaller nuclei form
OX: One or more neutrons is released
Y: A larger nucleus forms
Z: Large amounts of energy are released
OX: A larger nucleus forms
Y: Large amounts of energy are released
Z: Smaller nuclei form
Answers
The following depict the letters X, Y and Z
X: A larger nucleus formsY: Large amounts of energy are releasedZ: Smaller nuclei formWhat is fusion and fission?Fusion refers to a situation in which two light nuclei come together to form a heavier nucleus. Fission refers to the disintegration of a nucleus by the bombardment of a particle.
The portions that show the letters marked X, Y and Z are;
X: A larger nucleus formsY: Large amounts of energy are releasedZ: Smaller nuclei formMissing parts:
Roberto makes a graphic organizer to compare fusion nuclear reactions and fission nuclear reactions. A venn diagram with 2 intersecting circles The circle on the left is labeled fusion. The circle on the right is labeled fission. There is a Z in the fission circle. There is an Y in the intersecting area. There is an X in the fusion circle. Which labels belong in the regions marked X, Y, and Z?
OX: Smaller nuclei form
Y: Thermal energy is produced
Z: A larger nucleus forms
OX: Large amounts of energy are released
Y: One or more neutrons is released
Z: Smaller nuclei form
OX: One or more neutrons is released
Y: A larger nucleus forms
Z: Large amounts of energy are released
OX: A larger nucleus forms
Y: Large amounts of energy are released
Z: Smaller nuclei form
Learn more about nuclear fission:https://brainly.com/question/14590507
#SPJ1
Answer: D
Explanation: I just took the exam review in edge 2022 and got it right
PLEASE HELP ASAP!!
The invention and use of the microscope showed scientists that germs could cause illness. Although there had been various understandings before for why people become ill, the discovery that microscopic germs can make people sick completely changed scientific understanding of why diseases exist and spread.
This change is an example of what?
how a law changes when new evidence disproves it
how a law stays the same as new scientific inquiries are made
how a theory changes as new areas of science open up
how a theory stays the same when new research confirms it
Answers
According to the information in the fragment, it can be inferred that it is an example of how scientific development has consequences on pre-established theories and new areas are created in science (option C)
What is a scientific theory?A scientific theory is a term to refer to a set of concepts and observations that are proposed as principles to explain a class of phenomena.
According to the above, the discovery of germs and their relationship with human diseases was an event that changed scientific theories about human diseases because it demonstrated a different explanation than what was believed up to that time.
So, the correct answer is option C because this event changed scientific theory and opened new fields for scientific study and research.
Learn more about sciences in: https://brainly.com/question/12265124
#SPJ1
Answer:
Explanation:
According to the information in the fragment, it can be inferred that it is an example of how scientific development has consequences on pre-established theories and new areas are created in science (option C)
What is a scientific theory?
A scientific theory is a term to refer to a set of concepts and observations that are proposed as principles to explain a class of phenomena.
According to the above, the discovery of germs and their relationship with human diseases was an event that changed scientific theories about human diseases because it demonstrated a different explanation than what was believed up to that time.
So, the correct answer is option C because this event changed scientific theory and opened new fields for scientific study and research.
The F-35B Lightning II is a short-takeoff and vertical landing fighter jet. If it does a vertical takeoff to 20.00-m height above the ground and then follows a flight path angled at 26o with respect to the ground for 25 km, what is the final displacement in meters
Answers
The final displacement of the F-35B Lightning fighter jet is determined as 24,991.2 m.
Displacement of the flight
The displacement of the flight is calculated from triangle method of vector addition as follows;
Let the vertical take off = first length of triangleLet the flight path at 26⁰ = second length of triangleLet the displacement = third side of triangleAngle between the first two sides = 90 - 26⁰ = 64⁰
r² = a² + b² - 2abcosR
r² = 20² + 25000² - (2 x 20 x 25000) x cos(64)
r² = 624,562,028.9
r = 24,991.2 m
Thus, the final displacement of the F-35B Lightning fighter jet is determined as 24,991.2 m.
Learn more about displacement here: https://brainly.com/question/321442
#SPJ1
How to convert work done in joules into kilojoules?
Answers
1 Kilojoule [kJ] = 737.562 149 277 27 Foot pound force [ftlbf]
Answer:
divide by 1000
Explanation:
eg 1kJ is equal to 1000J
25. IF THE ROADWAY IS WET AND THE CAR STARTS TO SKID, YOU SHOULD: A. Slow down by pumping the brakes quickly and firmly B. Slow down by shifting to a lower gear C. Slowly ease your foot off the gas pedal
Answers
If the roadway is wet and the cars starts to skid, one should slow down by shifting to lower gear. The correct option is B.
What are gears?A gear is component used to transmit motion. They are used in cars, trucks, machines, bicycles, etc.
For a car to avoid skidding on the wet roads, one must drive the car slowly. This can be done by shifting the gear to the lower one. This will help car to keep balance when brakes are applied on wet roads.
Thus, the correct option is B.
Learn more about gears.
https://brainly.com/question/14455728
#SPJ1
Measuring Current as a Function of Voltage with a 20 Q Resistor
Voltage
M
Current Calculated
(A)
Current Experimental
(A)
1
5
10
20
50
Measuring Current as a Function of Resistance at 25 V
Resistance
Current Calculated
(10)
(A)
10
20
100
200
Determining Current in a Parallel Circuit
Observed
Resistor Set
(0)
Total
Resistance
Calculated
Current
(A)
Current
(A)
(10)
20, 20, 20
20, 20, 200
Voltage needed to raise current to 3.75 A (20, 20, 200 resistor set):
Calculated
Observed:
Calculating Power of Circuit Components
Current through Each Bulb
(A)
Table B
Table C
Table D
Observed Total Current
(A)
Current Experimental
(A)
Observed Current
through Each Resistor
(A)
Power Usage per Bulb
(
Answers
Answer:
Resistance at 25 V
Explanation:
(10)
(A)
10
20
100
200
Determining Current in a Parallel Circuit
Observed
Resistor Set
(0)
Total
Resistance
Calculated
Current
(A)
Current
(A)
(10)
20, 20, 20
20, 20, 200
Voltage needed to raise current to 3.75 A (20, 20, 200 resistor set):Calculated
Observed:
Calculating Power of Circuit Components
Current through Each Bulb
(A)
Table B
Table C
Table D
Observed Total Current
(A)
Current Experimental
(A)
Observed Current
through Each Resistor
(A)
Power Usage per Bulb
(
A mass is stretched 4 centimeters from the equilibrium position of a spring. if the displacement is doubled, what can be concluded about the restoring force? a. it is halved. b. it is doubled. c. it stays the same. d. it is increased by 4. e. it is decreased by 1 4
Answers
From a spring's equilibrium point, a mass is stretched by 4 cm. The restoring force will also double if the displacement doubles. Option B is correct.
What is spring force?The force required to extend or compress a spring by some distance scales linearly with respect to that distance is known as the spring force. Its formula is;
F = kx
The given data in the problem is;
F is the spring force =?
K is the spring constant= 8.5 N/m
x is the length by which spring got stretched = 1.2m
Given condition:
Displacement is doubled(x'=2x)
The spring force is directly propotional to the displacement of the spring;
F ∝ x
F' ∝ x'
If the displacement is doubled, the spring force will also double.
Hence option B is correct.
To learn more about the spring force refer to the link;
https://brainly.com/question/4291098
#SPJ1
Answer: From a spring's equilibrium point, a mass is stretched by 4 cm. The restoring force will also double if the displacement doubles. Option B is correct.
What is spring force?
The force required to extend or compress a spring by some distance scales linearly with respect to that distance is known as the spring force. Its formula is;
F = kx
The given data in the problem is;
F is the spring force =?
K is the spring constant= 8.5 N/m
x is the length by which spring got stretched = 1.2m
Given condition:
Displacement is doubled(x'=2x)
The spring force is directly propotional to the displacement of the spring;
F ∝ x
F' ∝ x'
If the displacement is doubled, the spring force will also double.
Hence option B is correct.
Explanation:
A light pointer is stuck to the rubber sheet so that it pivots about a point P near the
rim of the glass, as shown (enlarged) below.
This arrangement acts as a simple thermometer.
State two disadvantages of such a thermometer.
Answers
A conducting sphere with radius R carries total charge Q. What is the magnitude of the electric field at distances R/2 and 2R from the center of the sphere
Answers
Hello!
Distance of R/2:
Since a conducting sphere is referenced in this situation, all of its charge will be distributed along its SURFACE. Therefore, there is NO enclosed at a distance of R/2 from the center.
Using Gauss's Law:
[tex]\oint E \cdot dA = E\cdot A = \frac{Q_{encl}}{\epsilon_0}[/tex]
E = Electric field strength (N/C)
A = Area of Gaussian surface (m²)
Q = Enclosed charge (C)
ε₀ = Permittivity of free space C²/Nm²)
If the enclosed charge is 0, then:
[tex]E \cdot A = \frac{0}{\epsilon_0}\\\\\boxed{E = 0 \frac{N}{C}}[/tex]
Distance of '2R':
We can once again use Gauss's Law to solve. This time, however, a surface of radius '2R' encloses ALL of the charge of the sphere.
[tex]E \cdot A = \frac{Q_{encl}}{\epsilon_0}[/tex]
'A' is equivalent to the surface area of a sphere of radius '2R', or:
[tex]A = 4\pi (2R)^2\\\\A = 4\pi (4R^2)\\\\A = 16\pi R^2[/tex]
Substituting this expression back into Gauss's Law:
[tex]E \cdot 16\pi R^2 = \frac{Q}{\epsilon_0}\\\\E = \frac{Q}{16\pi R^2\epsilon_0}[/tex]
To simplify:
[tex]E = \frac{1}{4\pi \epsilon_0 } * \frac{Q}{4R^2}\\[/tex]
OR using k = 1/4πε₀:
[tex]\boxed{E = \frac{kQ}{4R^2}}[/tex]
The force on the wire is directed?
Answers
Answer: A
Explanation:
In case of a Crash the pilot of the plane jumped from it and opened his parachute after falling through 40m
Answers
Answer: 20m
Explanation: because half 40 is 20
Answer:
20m
Explanation: because half 40 is 20
PLS HELP: How do you think the mass media present mental disorders? Do you think the portrayals are accurate or inaccurate? Why?
Answers
The mass media present mental disorders by the daily soap programs and movies.
What is mass media?Mass media is the means of communication that reach large numbers of people in a few seconds through optical fiber transmission cables connection, such as television, newspapers, magazines, and radio.
Studies show that both entertainment and news media provide dramatic and distorted images of mental disorders. It can lead to more dangerous personality to develop in people including fear, rejection, derision and ridicule. The criminal activity has received heavy coverage in the mass media.
Thus, the mass media present mental disorders by the daily soap programs and movies.
Learn more about mass media.
https://brainly.com/question/16273365
#SPJ1
How does the amount of energy needed to melt 1 kg of ice at 0°C compare to the
amount of energy needed to change 1 kg of water to steam at 100°C? Base your
answer on the heat of fusion of water and the heat of vaporization of water.
(A) It takes about two-thirds as much energy to boil the water as to melt the ice.
(B) It takes the same amount of energy to boil the water and melt the ice.
(C) It takes about two-thirds as much energy to melt the ice as to boil the water.
(D) It takes more than six times as much energy to boil the water as to melt the
ice.
Answers
(A) It takes about two-thirds as much energy to boil the water as to melt the ice.
An object whose mass is 0.092 kg is initially at rest and then attains a speed of 75.0 m/s in 0.028 s. What average net force acted on the object during this time interval?
Answers
Answer:
F = 246.4 N
Explanation:
Concepts:Newton's Laws Of MotionFirst Law: (Law of Inertia)
Inertia refers to the tendency of an object to resist any change in its state of motion. Inertia is a measure of the objects mass.Second Law:
refers to an object's motion when a net force does not equal zero. Acceleration is directly proportional to the net force and inversely proportional to the object's mass.Third Law: (Action - Reaction)
Whenever one object exerts a force on a second object, the second objects exert an equal but opposite force on the first.Weight:
Force of gravity is the weight of an object and is measured in Newtons.Friction:
Frictional forces always oppose motion. The frictional forces ([tex]F_f[/tex]) is proportional to the coefficient of friction (Ц) and to the normal force [tex](F_n) F_f=uF_n[/tex].The normal force is a contact force which acts perpendicular to the common surface of contact.Now onto the steps:
----------------------------------
F = mΔV ÷ t
F = 0.093 x 75 ÷ 0.028
F = 246.4 N
Therefore, the average net force acted on the object during this time interval is 246.6 Newtons.
1. Predict whether the energy required to remove an electron from magnesium and potassium would be more or less than that required to remove an electron from sodium. Explain your prediction in terms of the forces and interactions involved in this process. \
FILL OUT THE TABLE PLEASE WITH A GOOD ANSWER FOR BRAINLIEST!
Answers
In both cases less energy is required
But comparetively Mg require more energy than K
Let's see the electron configuration of Both
[Mg]=1s²2s²2p⁶3s²=[Ne]3s²[K]=1s²2s²2p⁶3s²3p⁶4s¹=[Ar]4s¹K has only one valence electron so very less ionization enthalpy so less energy required
Mg has 2 so more IE hence more energy required
How do stairs reduce the
amount of effort needed to
get work done?
A. They require a large force over a long
distance.
B. They require a small force over a long
distance.
C. They require a large force over a short
time.
Answers
What stands in for a "creator" in scientists view of the universe?
*
1 point
The laws of physics
The "Big Bang"
String Theory
Humans create the universe
Answers
In scientists view of the universe The creator is replace by: (B). The "Big Bang"
Meaning of Big Bang
The Big bang is a theory propagated by scientist and astronomers to replace the creator.
The Big Bang is said to be a reason for the universe and all the planets in it. Scientist say the universe started as just a single point with very high temperature and density, and then here comes the big bang.
In conclusion, In scientists view of the universe The creator is replace by: The "Big Bang"
Learn more about The Big Bang: https://brainly.com/question/10865002
#SPJ1
Which word is described by this statement? This is the top of the volcano where sulfur-filled gasses and lava come out.
Answers
Answer:
I believe it is crater.
Calculate the energy used by a radio of power 30W in 1 minute.
Answers
Answer:
1800 j or 1.8 kj
Explanation:
Energy used = power (measured in watts) multiplied by time (measured by seconds)
1 minute is 60 seconds
30 multiplied by 60 is 1800
Answer:
1800 joule
Explanation:
Power (P) = 30W
Time (T) = 1 min =60 sec
P =(W/T)
30 = W / 60
W = 1800 joule
We know that Energy Is equivalent to Work done. So Energy used is 1800 joule.
why is it difficult to move the heavier object than the lighter object on any surface
Answers
Answer:
it's is because the heavier the object is the more it will be pulled down by gravity n the lighter the object the lesser the gravity will pull it down
Answer:
why is it difficult to move the heavier object than the lighter object on any surface
Water is added to a measuring cylinder containing 100 cm3 of liquid paraffin. (the density of paraffin is 0.80 g/ cm3 and that of the water is 1.0 g / cm3 .) as the water is added, the level of the paraffin rises to 150 cm3 . the paraffin and water do not mix. what finally is the total mass of liquid in the measuring cylinder?
Answers
The total of the liquid in the measuring cylinder given the data from the question is 130 g
What is density?The density of a substance is simply defined as the mass of the subtance per unit volume of the substance. Mathematically, it can be expressed as
Density = mass / volume
How to determine the mass of paraffin Density of paraffin = 0.80 g/cm³Volume of paraffin = 100 cm³Mass of paraffin =?Mass = Density × Volume
Mass of paraffin = 0.8 × 100
Mass of paraffin = 80 g
How to determine the mass of water Density of water = 1 g/cm³Volume of paraffin = 100 cm³Volume of paraffin + water = 150 cm³Volume of water = 150 – 100 = 50 cm³Mass of water =?Mass = Density × Volume
Mass of water = 1 × 50
Mass of water = 50 g
How to determine the mass of the mixture Mass of water = 50 gMass of paraffin = 80 gMass of mixture =?Mass of mixture = Mass of paraffin + Mass of water
Mass of mixture = 80 + 50
Mass of mixture = 130 g
Learn more about density:
https://brainly.com/question/952755
#SPJ1
25. a small container of water is placed on a turntable inside a microwave oven, at a radius of 12.0 cm from the center. the turntable rotates steadily, turning one revolution in each 7.25 s. what angle does the water surface make with the horizontal?
Answers
The angle that the water surface make with the horizontal is 0.527°.
How to calculate the angles?The water vapor moves at speed. Therefore,
v = 2πr/T = (2 × π × 0.120)/7.25
= 0.104m/s
Also, the top layer of water deals a downward force if gravity which will be:
= mv²/r = 0.104/0.12 = 0.0901
There, the angle will be:
= tan(0.0901/9.8)
= 0.527°
In this case, the angle that the water surface make with the horizontal is 0.527°.
Learn more about angles on:
brainly.com/question/25716982
#SPJ4
if water completely boils in 7 minutes, how long does it take to evaporate
Answers
Answer: 20 minutes
Explanation: omm its 20 minutes
A ball thrown vertically upwards from ground
level hits the ground after 4 s. Calculate the
maximum height it reached during its journey.
(SC/GCE)
Answers
parabolic motion
[tex]\tt t_{max}=\dfrac{2u~sin~\alpha }{g}[/tex]
[tex]\tt h_{max}=\dfrac{u^2sin^2\alpha }{2g}[/tex]
vertically upwards ⇒ α = 90°⇒sin 90° = 1
[tex]\tt 4=\dfrac{2u}{10}\rightarrow u=20~m/s[/tex]
[tex]\tt h_{max}=\dfrac{20^2}{2.10}=\boxed{\bold{20~m}}[/tex]