estimate the ph of a solution of sodium phenobarbital prepared dissolving 50 g of the substance in 1 l of water.

The correct answers are: proper orientation of the molecules; collisions between particles; and sufficient kinetic energy to break the bonds, as breaking chemical bonds in reactions requires proper orientation of the molecules and collisions between particles.

Chemical reactions involve the breaking of bonds between atoms in reactant molecues and the formation of new bonds between atoms in product molecules. Breaking these bonds requires a certain amount of energy, which can be supplied through collisions between particles and the proper orientation of the molecules involved in the reaction. When two reactant molecules collide, the orientation of their atoms is important. The atoms need to be in the correct position relative to each other for the chemical bonds to break and new bonds to form. 

Learn more about chemical reactions and energy here.

https://brainly.com/question/11637586?

#SPJ1

The final pH of the buffer solution is 9.13 after adding 0.03 mol HCl to 0.500 L of a buffer solution containing 0.024 M NH₃ and 0.20 M NH₄Cl.

To calculate the final pH, we will use the Henderson-Hasselbalch equation: pH = pKa + log([A-]/[HA]). First, find the pKa value of the conjugate acid NH₄⁺, which is 9.25. Next, calculate the moles of NH₃ and NH₄Cl present in the buffer solution by multiplying their molarity by the volume (0.5 L).

Then, subtract the moles of HCl added from the moles of NH₃ and add them to the moles of NH₄Cl to find the new concentrations of NH₃ and NH₄Cl. Finally, plug the new concentrations into the Henderson-Hasselbalch equation to find the final pH.

To know more about Henderson-Hasselbalch equation click on below link:

https://brainly.com/question/13423434#

#SPJ11

The equilibrium constant of the reaction is approximately 2.6 x  [tex]10^5[/tex] at 25°C.

The equilibrium constant (K) of the reaction can be calculated using the equation:

ΔG° = -RTlnK

where ΔG° is the standard free energy change, R is the gas constant, T is the temperature in Kelvin, and ln is the natural logarithm.

Given that ΔG°’ = -32.90 kJ/mol and the temperature is 25°C (298.15 K), we can solve for K as follows:

ΔG° = -RTlnK

-32.90 kJ/mol = -(8.314 J/mol•K)(298.15 K) lnK

lnK = -32.90 kJ/mol / (-8.314 J/mol•K)(298.15 K)

lnK = 12.23

K = [tex]e^{(lnK)[/tex]

K =[tex]e^{(12.23)[/tex]

K ≈ 2.6 x [tex]10^5[/tex]

Therefore, the equilibrium constant of the reaction is approximately 2.6 x  [tex]10^5[/tex] at 25°C.

Learn More about equilibrium

https://brainly.com/question/18849238

#SPJ4

62.66 kg of nickel must be added to 5.66 kg of copper to yield a liquidus temperature of 1200.

To calculate the amount of nickel needed to reach a liquidus temperature of 1200, we need to use the lever rule formula. This formula uses the proportions of the two metals in the alloy to determine the temperature at which the alloy will become completely liquid.

First, we need to determine the proportions of copper and nickel in the alloy. Let's assume that the final alloy will contain x kilograms of nickel.

The total mass of the alloy will be 5.66 + x kg.

Next, we need to determine the percentage of copper and nickel in the alloy. Assuming that the final alloy will contain 100% copper and nickel, we can write the following equation:

(5.66 / (5.66 + x)) × 100 = 100% - liquidus temperature drop

We know that the liquidus temperature drop is 1200 - the liquidus temperature of the copper-nickel alloy. Let's assume that the liquidus temperature of the alloy is 1300.

(5.66 / (5.66 + x)) × 100 = 100% - (1300 - 1200) / 1300 × 100

Simplifying this equation, we get:

(5.66 / (5.66 + x)) × 100 = 7.69

Solving for x, we get:

x = 62.66 kg

Therefore, we need to add 62.66 kg of nickel to 5.66 kg of copper to yield a liquidus temperature of 1200.

To know more about copper refer here:

https://brainly.com/question/24540382

#SPJ11

In regards to the examination of the properties of polystyrene, it is possible that dipping a styrofoam cup into solvents like toluene, distilled water, alcohol, or acetone could cause the cup to be reshaped due to the solvents dissolving or weakening the polystyrene material. However, it is important to note that these solvents can also be hazardous and should be handled with caution.

Labu Anomate University does not appear to be a real university or institution, so I cannot provide information on it. However, I can provide information on Freund's PR (Polarization Resistance) method.

Freund's PR method is a technique used to measure the corrosion rate of metal surfaces in various environments, including aqueous solutions and non aqueous liquids such as organic solvents like toluene, distilled water, alcohol, and acetone. The method involves measuring the polarization resistance of the metal surface, which is proportional to the corrosion rate. This technique is commonly used in industrial applications to determine the effectiveness of corrosion inhibitors and coatings.

To know more about inhibitors refer to

https://brainly.com/question/29519279

#SPJ11

The given statement is true. Tyrosine kinase receptors cannot initiate the transduction pathway until two receptors bind chemical messengers and move together forming a dimer.

Tyrosine kinases are important mediators of this signal transduction process, leading to cell proliferation, differentiation, migration, metabolism and programmed cell death. Tyrosine kinases are a family of enzymes, which catalyzes phosphorylation of select tyrosine residues in target proteins, using ATP.

The process occurs as follows:

1. Two chemical messengers bind to their respective receptor sites.
2. Upon binding, the receptors come together and form a dimer.
3. The dimerization activates the tyrosine kinase domains within the receptor.
4. This activation initiates the transduction pathway and leads to various cellular responses.

To learn more about transduction https://brainly.com/question/12836556

#SPJ11

The correct net ionic equation for the reaction that occurs when solutions of HCIO 4 and Ba(OH) 2 are mixed is:
2H⁺(aq) + 2OH⁻(aq) ⇒ 2H₂O(1) + Ba₂+(aq)

This is because the spectator ions, ClO4- and Ba2+, are not involved in the actual reaction and can be eliminated from the equation to give the net ionic equation.

The entire symbols of the reactants and products, as well as the states of matter under the conditions under which the reaction is occurring, are written in the complete equation of a chemical reaction.

Only those chemical species that are directly involved in the chemical reaction are written in the net ionic equation of the process.

In the net ion equation, mass and charge must be equal.

It is utilised in double displacement processes, redox reactions, and neutralisation reactions.

After removing the spectator ions, we may discuss the final ionic process using the net reaction equation. Keep in mind that we refer to the ions that do not participate in the reaction as spectator ions.

Learn more about net ion equation here

https://brainly.com/question/22885959

#SPJ11

It would take 176 minutes for the amount of potassium-44 to decrease from 60.0 mg to 7.50 mg.

To calculate how long it would take for the amount of potassium-44 to decrease from 60.0 mg to 7.50 mg, we need to use the half-life of potassium-44, which is 22 minutes.

First, we need to determine how many half-lives have occurred during this time. We can do this by dividing the initial amount of potassium-44 by the final amount: 60.0 mg / 7.50 mg = 8.

So, 8 half-lives have occurred. Next, we need to determine the total amount of time it would take for 8 half-lives to occur. We can do this by multiplying the half-life by the number of half-lives: 22 min/half-life x 8 half-lives = 176 minutes

Therefore, it would take 176 minutes for the amount of potassium-44 to decrease from 60.0 mg to 7.50 mg.

To know more about  potassium, refer here:

https://brainly.com/question/13321031#

#SPJ11

The equilibrium expression for the following reaction? h2so4 (l) ⇌ so3 (g) h2o (l):  the final equilibrium expression for this reaction is: Kc = [SO3]

The equilibrium expression for the given reaction is:

Kc = [SO3][H2O] / [H2SO4]

where Kc is the equilibrium constant, [SO3], [H2O], and [H2SO4] are the molar concentrations of sulfur trioxide, water, and sulfuric acid respectively at equilibrium.
Hello! I'm happy to help with your question. The equilibrium expression for the reaction H2SO4 (l) ⇌ SO3 (g) + H2O (l) can be written using the equilibrium constant (Kc).

First, let's write the balanced chemical equation:
H2SO4 (l) ⇌ SO3 (g) + H2O (l)

Next, we'll write the equilibrium expression using the concentrations of the products and reactants:

Kc = [SO3] * [H2O] / [H2SO4]

In this expression, [SO3], [H2O], and [H2SO4] represent the equilibrium concentrations of the respective species. Keep in mind that only the concentrations of gases (SO3 in this case) are included in the equilibrium constant expression. Liquid concentrations, such as H2SO4 and H2O, do not affect the value of Kc.

So, the final equilibrium expression for this reaction is:

Kc = [SO3]

to learn more about equilibrium constant click here:

brainly.com/question/29359391

#SPJ11

The manufacture of ammonia from nitrogen and hydrogen is an exothermic reaction, which means that it releases heat. According to Le Chatelier's principle, an increase in temperature favors the endothermic direction of a reversible reaction. Therefore, a lower temperature would give a greater yield of ammonia.

In this reaction, nitrogen and hydrogen combine to form ammonia. The reverse reaction is also possible, where ammonia breaks down into nitrogen and hydrogen. This reaction is exothermic, which means that it releases heat. According to Le Chatelier's principle, an increase in temperature favors the endothermic direction of a reversible reaction. Therefore, if the temperature is increased, the yield of ammonia would decrease as the reaction would shift towards the reactants.

On the other hand, a lower temperature would favor the exothermic direction and increase the yield of ammonia. Hence, room temperature would give a greater yield of ammonia than a temperature of 100°C.

In conclusion, a lower temperature would give a greater yield of ammonia as it favors the exothermic direction of the reaction.

Learn more about ammonia here:

https://brainly.com/question/15409518

#SPJ11

A sample of nitrogen gas collected at a pressure of 766 mm Hg and a temperature of 297 K has a mass of 27.0 grams. The volume of the sample is 24.13 liters.

To find the volume of the sample of nitrogen gas, we can use the ideal gas law:
PV = nRT
where P is the pressure in atmospheres (atm), V is the volume in liters (L), n is the number of moles of gas, R is the gas constant (0.0821 L·atm/K·mol), and T is the temperature in Kelvin (K).
First, we need to convert the pressure from mm Hg to atm:
1 atm = 760 mm Hg
So, P = 766 mm Hg / 760 mm Hg/atm = 1.01 atm
Next, we can use the mass of the sample to calculate the number of moles of nitrogen gas:
n = m/M
where m is the mass of the gas (27.0 g) and M is the molar mass of nitrogen (28.0 g/mol).
n = 27.0 g / 28.0 g/mol = 0.964 mol
Now we can plug in the values for P, n, R, and T and solve for V:
V = nRT/P
V = (0.964 mol)(0.0821 L·atm/K·mol)(297 K)/(1.01 atm)
V = 22.5 L
Therefore, the volume of the sample of nitrogen gas is 22.5 L.
To find the volume of the nitrogen gas sample, we can use the Ideal Gas Law formula, which is PV = nRT. We need to determine the values for pressure (P), number of moles (n), temperature (T), and the gas constant (R). Then, we can solve for the volume (V).
Given:
Pressure (P) = 766 mm Hg (we need to convert it to atm, so we'll use the conversion factor: 1 atm = 760 mm Hg)
Temperature (T) = 297 K
Mass of nitrogen gas = 27.0 grams
First, convert the pressure to atm:
P = 766 mm Hg * (1 atm / 760 mm Hg) = 1.0079 atm
Next, find the number of moles (n) using the molar mass of nitrogen gas (N2) which is 28.02 g/mol:
n = mass / molar mass = 27.0 grams / 28.02 g/mol = 0.9636 mol
Now, we have P, n, and T, and the value of the gas constant (R) is 0.0821 L·atm/mol·K. Plug the values into the Ideal Gas Law formula:
1.0079 atm * V = 0.9636 mol * 0.0821 L·atm/mol·K * 297 K
Solve for V:
V = (0.9636 mol * 0.0821 L·atm/mol·K * 297 K) / 1.0079 atm = 24.13 L
Therefore, the volume of the nitrogen gas sample is 24.13 liters.

To learn more about Gases, click here:

brainly.com/question/14812509

#SPJ11

The starting materials to form imine A are tert-butylamine and benzaldehyde.

Imines are compounds that contain a carbon-nitrogen double bond and are formed by the reaction of a primary amine with a carbonyl compound, typically an aldehyde or a ketone.

To deduce the starting materials for the synthesis of imines A and B, we need to analyze the given reaction scheme and trace the reaction steps backward.

In the reaction scheme, imine A is formed by the reaction of a primary amine with an aldehyde.

The amine used is tert-butylamine, while the aldehyde used is benzaldehyde. Therefore,

On the other hand, imine B is formed by the reaction of a primary amine with a ketone.

The amine used is aniline, while the ketone used is cyclohexanone. Therefore, the starting materials to form imine B are aniline and cyclohexanone.

To know more about carbonyl compound visit:

https://brainly.com/question/17422534

#SPJ1

The equilibrium constant Kc for the given reaction is 1.6 × 10¹¹.

The equilibrium constant expression for the given reaction is:

Kc = ([Ag(CN)₂⁻] [Cl⁻])/([AgCl] [CN⁻]²)

To find Kc, we need to determine the concentrations of the species at equilibrium.

Since AgCl is a solid, its concentration is constant and can be assumed to be 1 (or any other convenient value). Let x be the concentration of Ag(CN)₂⁻ at equilibrium, then the concentrations of Cl⁻ and CN⁻ are also equal to x, as two moles of CN⁻ react with one mole of AgCl to form one mole of Ag(CN)₂⁻ and one mole of Cl⁻.

The solubility product expression for AgCl is:

Ksp = [Ag⁺] [Cl⁻]

Since [Ag⁺] is negligible compared to [CN⁻] in the presence of excess CN⁻, we can assume that [Cl⁻] = [AgCl] = 1. Therefore:

Ksp = 1 = [Ag⁺] [Cl⁻] = [Ag⁺]

Substituting the concentrations of the species into the equilibrium constant expression, we get:

Kc = ([Ag(CN)₂⁻] [Cl⁻])/([AgCl] [CN⁻]²) = (x²)/(1 x x²) = x

The formation constant expression for Ag(CN)₂⁻ is:

Kf = ([Ag(CN)₂⁻])/([Ag⁺] [CN⁻]²)

Substituting [Ag⁺] = 1 and solving for [Ag(CN)₂⁻], we get:

[Ag(CN)₂⁻] = Kf [Ag⁺] [CN⁻]² = 1.0 × 10⁻²¹ × 1 × x² = 1.0 × 10⁻²¹ x²

Substituting this expression for [Ag(CN)₂⁻] into the equilibrium constant expression, we get:

Kc = ([Ag(CN)₂⁻] [Cl⁻])/([AgCl] [CN⁻]²) = (1.0 × 10⁻²¹ x² x)/(1 x x²) = 1.6 × 10¹¹

learn more about solubility product expression here:

https://brainly.com/question/16406992

#SPJ11

The concentration of CO (g) at equilibrium is approximately 0.064 M.

We can use the equilibrium expression for the reaction:
Kc = [Ni (CO)4] / ([Ni][CO]^4)

We are given that [Ni (CO)4] = 0.85 M, and we can assume that the initial concentration of Ni (s) is negligible compared to the concentration of CO (g) and Ni (CO)4 (g).

Therefore, we can use the following approximation: [Ni] ≈ 0.

Substituting the given values and approximation into the equilibrium expression, we get:
5.0 x 104 M-3 = 0.85 M / (0 x [CO]^4)
Solving for [CO], we get:
[CO] = (0.85 M / 5.0 x 104 M-3)1/4
[CO] ≈ 0.086 M

Therefore, the concentration of CO (g) at equilibrium is approximately 0.086 M.

To find the concentration of CO (g) at equilibrium, we can use the expression for the equilibrium constant, Kc, which is:
Kc = [Ni(CO)₄] / ([Ni] * [CO]⁴)

Given that [Ni(CO)₄] = 0.85 M and Kc = 5.0 x 10⁴ M⁻³, we can solve for the concentration of CO:
5.0 x 10⁴ M⁻³ = 0.85 M / ([Ni] * [CO]⁴)

Since [Ni] is a solid, its concentration remains constant and does not affect the equilibrium, so we can rewrite the equation as: 5.0 x 10⁴ M⁻³ = 0.85 M / [CO]⁴

Now, solve for [CO]:
[CO]⁴ = 0.85 M / (5.0 x 10⁴ M⁻³)
[CO]⁴ ≈ 1.7 x 10⁻⁵ M

To find [CO], take the fourth root of the result:
[CO] = (1.7 x 10⁻⁵ M)^(1/4)
[CO] ≈ 0.064 M

Thus, the concentration of CO (g) at equilibrium is approximately 0.064 M.

Know more about equilibrium: brainly.com/question/30807709

#SPJ11

For the first question, the reaction can be classified as an acid-base neutralization reaction.

For the second question, the reaction can be classified as a precipitation reaction.

For the third question, using the formula V = m/density, we can calculate the volume of the ethyl alcohol to be 0.196 mL.

For the fourth question, using the formula T in ºC = (T in ºF - 32)/1.8, we can convert the temperature from 75 oF to Celsius degrees, which is 23.9 °C.

1. The reaction NaOH + H₂SO₄ → Na₂SO₄ + H₂O is classified as an acid-base neutralization reaction.

2. The reaction (NH₄)₃PO₄ + Ba(NO₃)₂ → Ba₃(PO₄)₂ + NH₄NO₃ is classified as a precipitation reaction.

3. With 0.155 g of ethyl alcohol and a density of 0.789 g/mL, the volume of alcohol is V = m/density, which results in V = 0.155 g / 0.789 g/mL = 0.196 mL.

4. To convert the room temperature from 75 °F to Celsius, use the formula [T in ºC = (T in F - 32) / 1.8]. This results in a temperature of (75 - 32) / 1.8 = 23.9 °C.

Visit here to learn more about  reaction : https://brainly.com/question/17434463
#SPJ11

The pH of the buffer solution is slightly basic due to the presence of a weak base.

To determine the pH of the buffer solution, we need to use the Henderson-Hasselbalch equation: pH = pKa + log ([A-]/[HA]), where pKa is the acid dissociation constant of the weak acid, [A-] is the concentration of the conjugate base, and [HA] is the concentration of the weak acid.

In this case, the weak base and its conjugate acid act as the acid and base components of the buffer, respectively. The pKa can be calculated using the expression pKa = -log(Ka), where Ka is the equilibrium constant for the dissociation of the weak acid.

Plugging in the given values, we get a pKa of 9.17. Then, we can substitute the concentrations of the weak base and its conjugate acid into the Henderson-Hasselbalch equation and solve for the pH, which turns out to be 9.59.

To know more about buffer solution refer here:

https://brainly.com/question/24262133#

#SPJ11

The balanced chemical equation for the reaction between HCl and NaOH is: the enthalpy change for the reaction between 1.0 M HCl and 1.0 M NaOH is -54.22 kJ/mol HCl (since the reaction is exothermic).

HCl(aq) + NaOH(aq) → NaCl(aq) + [tex]H_{2} O[/tex](l)

First, we need to calculate the amount of heat released or absorbed by the reaction using the formula:

q = m·C·ΔT

where q is the heat absorbed or released by the reaction, m is the mass of the solution, C is the specific heat of the solution, and ΔT is the change in temperature of the solution. Since the total volume of the solution is 100 mL and the density is 1.0 g/mL, the mass of the solution is:

m = 100 mL × 1.0 g/mL = 100 g

The specific heat of the solution is given as 4.18 J/g-K. The change in temperature is:

ΔT = 27.5°C - 21.0°C = 6.5°C

Therefore, the amount of heat released or absorbed by the reaction is:

q = 100 g × 4.18 J/g-K × 6.5°C = 2,711 J

Next, we need to convert the amount of heat to the enthalpy change for the reaction per mole of HCl. Since we mixed 50 mL of 1.0 M HCl with 50 mL of 1.0 M NaOH, we have 0.05 moles of HCl in the solution. Therefore, the enthalpy change per mole of HCl is:

ΔH = q / n

where n is the number of moles of HCl. Therefore,

ΔH = 2,711 J / 0.05 mol = 54,220 J/mol

To express the result in kJ/mol, we need to divide by 1000:

ΔH = 54.22 kJ/mol

Therefore, the enthalpy change for the reaction between 1.0 M HCl and 1.0 M NaOH is -54.22 kJ/mol HCl (since the reaction is exothermic).

Learn more about chemical equation

https://brainly.com/question/19626681

#SPJ4

The reaction of methylamine with water is; CH₃NH₂ (aq) + H₂O (l) ⇌ CH₃NH₃⁺ (aq) + OH⁻ (aq), the pH of the solution is 11.42, and  the solution will become more acidic.

The reaction of methylamine with water is;

CH₃NH₂ (aq) + H₂O (l) ⇌ CH₃NH₃⁺ (aq) + OH⁻ (aq)

In this reaction, CH₃NH₂ is a weak base and H₂O is the acid. The conjugate acid of CH₃NH₂ is CH₃NH₃⁺ and the conjugate base of H₂O is OH⁻.

The equilibrium constant expression for this reaction is;

Kb = [CH₃NH₃⁺][OH⁻]/[CH₃NH₂]

At equilibrium, we can assume that x moles of CH₃NH₂ react with x moles of H₂O to form x moles of CH₃NH₃⁺ and x moles of OH⁻. Therefore, we can write;

Kb = x₂ / (0.0251 - x)  

Solving for x, we get;

x = 0.00263 M

Therefore, the concentration of OH⁻ at equilibrium is 0.00263 M. To find the concentration of H⁺, we can use the equation;

Kw = [H⁺][OH⁻]

where Kw is the ion product constant for water, which is 1.0 x 10⁻¹⁴ at 25°C. Solving for [H⁺], we get;

[H⁺] = Kw / [OH⁻] = 1.0 x 10⁻¹⁴ / 0.00263 = 3.8 x 10⁻¹² M

Taking the negative logarithm of [H⁺], we get;

pH = -log[H⁺] = -(-11.42) = 11.42

Therefore, the pH of the solution is 11.42.

When you add one drop of Na₂CO₃ (aq) to the solution of methylamine, the Na₂CO₃ will react with water to produce Na⁺ and OH⁻. The OH⁻ ions will react with the CH₃NH₃⁺ ions in the solution to form CH₃NH₂ and H₂O.

This reaction will shift the equilibrium to the left, decreasing the concentration of OH⁻ and increasing the concentration of H⁺. Therefore, the solution will become more acidic.

To know more about methylamine here  

https://brainly.com/question/28819363

#SPJ4

∆s = R ln 10, where R is the gas constant is the value of ∆s if one mole of an ideal gas is expanded reversibly and isothermally from 1.0 bar to 0.1 bar.

The change in entropy (∆s) of an ideal gas during an isothermal reversible expansion is given by [tex]∆s = nR ln (V2/V1),[/tex]  where n is the number of moles, R is the gas constant, V1 is the initial volume, and V2 is the final volume. Here, n = 1 mole, [tex]V1 = RT/P1,[/tex] and [tex]V2 = RT/P2,[/tex]  where T is the temperature in Kelvin, [tex]P1 = 1.0[/tex] bar, and[tex]P2 = 0.1[/tex] bar. Substituting these values, we get [tex]∆s = R ln (P1/P2) = R[/tex]  ln 10. Since the pressure decreases during expansion, the entropy of the gas increases. Hence, the sign of ∆s is positive.

learn more about ideal gas here:

https://brainly.com/question/31463642

#SPJ11

Cl₂ ≤OClO₂≤ ClO₂ is the proper sequence of increasing bond angles in the following species. This is owing to the fact that in ClO₂, there are two lone pairs of electrons that oppose one another.

Causing two oxygen atoms to move in closer together and resulting in a decrease in bond angle. Therefore, the bond angle in ClO₂ is less than 118°, which is the bond angle in ClO₂ where chlorine has less electrons. ClO₂ has an angular structure. With a bond angle of 118⁰ and a Cl-O bond length of 1.47A⁰, the Cl atom is sp₂-hybridized in the angular molecule.

To know more about bond angles, click here:

https://brainly.com/question/13751116

#SPJ4

The equilibrium hole concentration (p) is 2.25*10^{3 }cm^-3.

In the given information, the concentration of electrons (No) is 2*10^{15} cm3 and the concentration of acceptor impurities (NA) is 3* 10^{17} cm3. Since the dopants are fully ionized, the concentration of holes (p) equals the concentration of acceptor impurities (NA).
To find the equilibrium electron concentration (n), we use the following formula:
n_i^2 = No * NA
Where n_i is the intrinsic carrier concentration. At room temperature, n_i = 1.5*10^{10} cm^{-3}.
Substituting the given values, we get:
(1.5*10^{10})^{2 }= 2*10^{15} * 3*10^{17}
n = sqrt((2*10^{15} * 3*10^{17})}{1.5*10^10) }
n = 6*10^{6} cm^{-3}
Therefore, the equilibrium electron concentration (n) is 6*10^{6} cm^{-3} and the equilibrium hole concentration (p) is 3*10^{17} cm^{-3}.
For the second part of the question, if the concentration of electrons (n) changes to 10^{17} cm^{-3}, we can use the following formula:
n * p = n_i^2
Substituting the given values, we get:
10^17 * p = (1.5*10^10)^2
p = \frac{(1.5*10^10)^{2}}{ 10^{17}}
p = 2.25*10^{3 }cm^{-3}
Therefore, the equilibrium hole concentration (p) is 2.25*10^{3} cm^{-3}.

learn more about  equilibrium Refer:  https://brainly.com/question/30694482

#SPJ11

At equivalence, the pH can be greater than 7, less than 7, or equal to 7, depending on the nature of the acid and base involved in the reaction.

1. If the acid and base are both strong (e.g., HCl and NaOH), the pH will be equal to 7. This is because strong acids and bases completely dissociate in water, and at equivalence, the number of moles of [tex]H^+[/tex] ions and [tex]OH^-[/tex] ions will be equal, leading to a neutral solution.

2. If the acid is strong and the base is weak (e.g., HCl and [tex]NH_3[/tex]), the pH will be less than 7. This is because, at equivalence, the weak base will not completely neutralize the strong acid, leaving some [tex]H^+[/tex]  ions in the solution, which results in an acidic solution.

3. If the acid is weak and the base is strong (e.g., [tex]CH_3COOH[/tex] and NaOH), the pH will be greater than 7. This is because, at equivalence, the strong base will completely neutralize the weak acid, leaving some [tex]OH^-[/tex] ions in the solution, which results in a basic solution.

In summary, the pH at equivalence depends on the nature of the acid and base involved in the reaction.

Learn more about pH here: https://brainly.com/question/491373

#SPJ11

The molarity of the solution made by dissolving 125 g of Na₃PO₄ in water resulting to a volume of 250 ml is approximately 3.05 M.

To calculate the molarity (M) of the solution, we need to know the moles of solute (Na₃PO₄) and the volume of the solution in liters.

1. Convert grams of Na₃PO₄ to moles:
Molecular weight of Na₃PO₄ = (3 × 22.99) + (1 × 30.97) + (4 × 16.00) = 68.97 + 30.97 + 64.00 = 163.94 g/mol

125 g Na₃PO₄ / 163.94 g/mol ≈ 0.762 moles of Na₃PO₄

2. Convert volume of the solution to liters:
250 mL = 250/1000 = 0.25 L

3. Calculate the molarity (M):
M = moles of solute / volume of solution in liters
M = 0.762 moles / 0.25 L ≈ 3.05 M

The molarity of the Na₃PO₄ solution is approximately 3.05 M.

Learn more about molarity here: https://brainly.com/question/30404105

#SPJ11

360g is the mass of Argon present in a sample occupying 76.3L at 31C and 240 kPa of pressure.

A body's mass is an inherent quality. Prior to the discoveries of the atom or particle physics, it was widely considered to be tied to the amount of matter within a physical body.

It was discovered that, despite having the same quantity of matter in theory, different atoms and elementary particles have varied masses. There are various conceptions of mass in contemporary physics that are theoretically different but physically equivalent.

P×V = n×R×T  

240 ×76.3= n×0.821×310

n=10 moles

mass = 10×36=360g

To know more about mass, here:

https://brainly.com/question/19694949

#SPJ1

Answer:

higher the temp higher the melting rate

Explanation:

the higher the temp the more energy is put into the system in order to break intermolecular forces between molecules and allow it to change state.

The compound that is antiaromatic is option (iii). Anti-aromatic compounds are characterized by having a planar, cyclic ring of atoms with a total of 4n electrons in the π system, where n is any integer.

The electrons in the π system interact in such a way that the molecule is destabilized, making it less stable than a non-aromatic or even an aromatic compound.

Option (iii) is a planar cyclic ring with 8 π electrons in its π system, which makes it antiaromatic.

The compound has two double bonds and two lone pairs of electrons on the nitrogen atoms, and it follows the Hückel's rule (4n+2) for aromaticity, but since it has a total of 8 π electrons, it does not meet the requirements to be aromatic.

Option (i) has 10 π electrons, making it aromatic. Option (ii) has 6 π electrons, making it also aromatic.

Option (iv) has 12 π electrons, making it non-aromatic. Therefore, the correct answer is option (iii), which is antiaromatic.

To know more about antiaromatic, refer here:

https://brainly.com/question/30215728#

#SPJ11

A saturated aqueous solution remains saturated even if water is unintentionally added to it. This statement is false.

When water is added to a saturated aqueous solution, the solution will no longer be saturated, as the addition of water will dilute the concentration of solutes in the solution.

A saturated aqueous solution contains the maximum amount of solutes that can be dissolved in the solvent, at a given temperature and pressure. When more solutes are added to the solution, they will not dissolve and instead form a separate phase. This is because the solution is already at equilibrium, and any additional solutes will not be able to dissolve.

When water is added to the solution, the concentration of solutes in the solution will decrease, as the same amount of solutes is now dispersed in a larger volume of solvent. The solution will no longer be saturated, as there is no room for more solutes to dissolve in the solvent.

To learn more about aqueous solutions

https://brainly.com/question/22280117

#SPJ4

Benzophenone is less polar than benzhydrol because it contains a carbonyl group (C=O) which is a polar functional group, but the two phenyl rings on either side of the carbonyl group cancel out the polarity due to their symmetrical arrangement. On the other hand, benzhydrol contains an OH group which is a highly polar functional group that increases the overall polarity of the molecule.

Therefore, benzhydrol is more polar than benzophenone.
Benzophenone is less polar than benzhydrol because benzophenone has a ketone functional group (C=O), while benzhydrol has an alcohol functional group (OH). The alcohol group in benzhydrol is capable of forming stronger hydrogen bonds due to the presence of an oxygen-hydrogen bond (O-H), making it more polar than benzophenone.

Visit here to learn more about benzophenone brainly.com/question/31408222

#SPJ11

The estimated resistivity of copper is 1.75 x 10⁻⁸ Ωm, and the resistance of the wire at 100°C is 1.33 Ω.

To estimate the resistivity of copper, use the formula:

Resistivity (ρ) = (Resistance (R) × Cross-sectional area (A)) / Length (L)

First, calculate the cross-sectional area (A) of the wire:

A = π × (radius)² = π × (0.350 x 10⁻³ m)²≈ 3.85 x 10⁻⁷ m²
Now, find the resistivity:

ρ ≈ (1.15 Ω × 3.85 x 10⁻⁷ m²) / 27.0 m ≈ 1.75 x 10⁻⁸ Ωm

To find the resistance at 100°C, use the temperature coefficient of resistance formula:

R_T = R_0 × (1 + α × ΔT)

Where R_T is the resistance at temperature T, R_0 is the initial resistance, α is the temperature coefficient, and ΔT is the change in temperature.

ΔT = 100°C - 26°C = 74°C
α = 0.393% / °C = 0.00393 / °C

R_T = 1.15 Ω × (1 + 0.00393 / °C × 74°C) ≈ 1.33 Ω

To know more about temperature coefficient click on below link:

https://brainly.com/question/29083034#

#SPJ11

In a 1-butanol molecule, the hydrophobic part is the butyl group (-CH₂CH₂CH₂CH₃), which is a long, nonpolar chain of carbon and hydrogen atoms.

The hydroxyl group (-OH) at the other end of the molecule is hydrophilic, as it is polar and can form hydrogen bonds with water molecules. The hydrophobic butyl group, on the other hand, tends to repel water and interact more favorably with other hydrophobic molecules.

To expand further, the term "hydrophobic" refers to a molecule or part of a molecule that tends to repel water and other polar substances. This is because hydrophobic substances are typically nonpolar or have a low polarity, meaning they have no or very few electrically charged or partially charged areas.

Water, on the other hand, is a polar molecule, meaning it has a partial positive charge on one end and a partial negative charge on the other. Polar substances like water interact favorably with other polar molecules and are repelled by nonpolar molecules.

learn more about hydrophobic here:

https://brainly.com/question/29418866

#SPJ11