Induced emf in the loop is 8.4 x 10⁻⁵ A
power dissipated by the loop while the magnetic field is changing is 0.029 W
The induced emf in the loop can be calculated using Faraday's law, which states that the magnitude of the induced emf is proportional to the rate of change of magnetic flux through the loop. Since the loop is perpendicular to the magnetic field, the magnetic flux through the loop is given by the product of the magnetic field strength and the area of the loop. Therefore, the induced emf can be calculated as follows:
emf = -dΦ/dt = -(Bf - Bi)/t
where Bf is the final magnetic field strength, Bi is the initial magnetic field strength, and t is the time taken for the magnetic field to change. Substituting the given values, we get:
emf = -(0 - 1.4)/0.4 = 3.5 V
The power dissipated by the loop can be calculated using the formula P = I²R, where I is the current flowing through the loop and R is its resistance. Since the loop is a closed circuit, the induced emf will cause a current to flow through it. Using Ohm's law, we can calculate the current as follows:
I = emf/R = 3.5/41600 = 8.4 x 10⁻⁵ A
Substituting this value into the power formula, we get:
P = I²R = (8.4 x 10⁻⁵)² x 41600 = 0.029 W
Therefore, the power dissipated by the loop while the magnetic field is changing is very small, indicating that the heating of tissues under normal circumstances is also very small.
To learn more about induced emf https://brainly.com/question/13744192
#SPJ11
what is the potential difference between the top and the bottom of the truck's side panels? express your answer in volts.
Energy that emerges from location or configuration is known as potential energy.
Thus, According to the fundamental definition of energy as the ability to perform work, the SI unit for energy is the joule, which is equal to one newton times one meter.
Because of its location in a gravitational field, electric field, or magnetic field, an object may have the ability to do work (gravitational potential energy), electric potential energy, or magnetic potential energy.
As a result of a stretched spring or another elastic deformation, it can possess elastic potential energy.
Thus, Energy that emerges from location or configuration is known as potential energy.
Learn more about potential energy, refer to the link:
https://brainly.com/question/24284560
#SPJ12
you know your mass is 65 kg , but when you stand on a bathroom scale in an elevator, it says your mass is 79 kg. What is the magnitude of the acceleration of the elevator? Express your answer using two significant figures.
The magnitude of the acceleration of the elevator if the mass is 65 kg but the bathroom scale reads 79 kg is 2.1 m/s².
To find the magnitude of the acceleration of the elevator, given that the mass is 65 kg and the bathroom scale reads 79 kg, we can use the formula F = ma (force equals mass times acceleration).
First, find the apparent weight:
= 79 kg × 9.81 m/s² (gravitational acceleration)
= 774.99 N (Newtons)
Next, find the actual weight:
= 65 kg × 9.81 m/s²
= 637.65 N
Now, find the net force:
= 774.99 N - 637.65 N
= 137.34 N
Finally, divide the net force by your mass to find the acceleration:
= 137.34 N / 65 kg
= 2.11 m/s²
So, the magnitude of the acceleration of the elevator is approximately 2.1 m/s².
Learn more about magnitude of the acceleration: https://brainly.com/question/31239315
#SPJ11
The electric potential along the x-axis is V =200x2 V, where x is in meters. What is Ex at x = 0m? What is Ex at x =2m?
The electric field at x=2m is 800V/m since the derivative of 200x² with respect to x is 400x, and when x=2m, Ex=400*2=800V/m.
The electric field along the x-axis can be found by taking the derivative of the electric potential function with respect to x.
Therefore, Ex at x=0m would be 0 since the derivative of any constant term (in this case, the constant term is 0) is 0. Ex at x=2m would be 800V/m since the derivative of 200x² with respect to x is 400x and when x=2m, Ex=400*2=800V/m.
The electric potential is a measure of the electric potential energy per unit charge at a given point in space. It is a scalar quantity and is related to the electric field, a vector quantity, by a gradient relationship.
The electric field is the negative gradient of the electric potential, which means that the electric field is the rate at which the potential changes per unit distance in a particular direction.
In this case, the electric potential along the x-axis is given as V=200x², and the electric field can be found by taking the derivative of this function with respect to x. The electric field at x=0m is zero since the derivative of any constant term is zero.
To know more about derivative click on below link:
https://brainly.com/question/25324584#
#SPJ11
Three point charges are located on the x-axis. The first charge, q1 = +10 µC, is at x = -1. 0 m. The second charge, q2 = +20 µC, is at the origin. The third charge, q3 = - 30 µC, is located at x = +2. 0 m. What is the net force on q2?
The net force on q2 to be 1.08 x 10^-3 N directed towards q1, because the charges on q1 and q3 are oppositely charged and the force between them is attractive, while the force between q2 and the other two charges is repulsive.
We have three point charges located on the x-axis. The first charge, q1, has a charge of +10 µC and is positioned at x = -1.0 m. The second charge, q2, has a charge of +20 µC and is located at the origin (x = 0). The third charge, q3, has a charge of -30 µC and is positioned at x = +2.0 m.
We need to find the net force on q2 due to the other two charges. We can calculate this using Coulomb's law, which gives us a formula to calculate the force between two charges.
Plugging in the values, we get the net force on q2 to be 1.08 x 10^-3 N directed towards q1, because the charges on q1 and q3 are oppositely charged and the force between them is attractive, while the force between q2 and the other two charges is repulsive.
Learn more about force:
https://brainly.com/question/26115859
#SPJ4
It is shown in more advanced courses that charged particles in circular orbits radiate electromagnetic waves, called cyclotron radiation. As a result, a particle undergoing cyclotron motion with speed vis actually losing kinetic energy at the ratedK/dt=?(?0q4/6?cm2)B2v2Part A.How long does it take an electron to radiate away half its energy while spiraling in a 7.0 T magnetic field?Express your answer with the appropriate units.
The rate at which kinetic energy is lost due to cyclotron radiation is given by: [tex]$\frac{dK}{dt} = -\frac{q^4}{6\pi\epsilon_0 m^2 c^3}B^2v^2$[/tex]
We want to find the time it takes for an electromagnetic waves or electron to radiate away half its energy while spiraling in a 7.0 T magnetic field.
Let's assume the initial kinetic energy of the electron is K. Then the time it takes for the electron to radiate away half its energy can be found by solving the following equation for t:
[tex]$\frac{1}{2}K = \int_{0}^{t}\frac{dK}{dt}dt$\\$\frac{1}{2}K = \int_{0}^{t}-\frac{q^4}{6\pi\epsilon_0 m^2 c^3}B^2v^2dt$\\$\frac{1}{2}K = -\frac{q^4}{6\pi\epsilon_0 m^2 c^3}B^2\int_{0}^{t}v^2dt$\\[/tex][tex]$\frac{1}{2}K = \int_{0}^{t}\frac{dK}{dt}dt$\\$\frac{1}{2}K = \int_{0}^{t}-\frac{q^4}{6\pi\epsilon_0 m^2 c^3}B^2v^2dt$\\$\frac{1}{2}K = -\frac{q^4}{6\pi\epsilon_0 m^2 c^3}B^2\int_{0}^{t}v^2dt$\\[/tex]
Now we need to express v in terms of the initial kinetic energy K. The kinetic energy of an electron in a magnetic field is given by:
[tex]$K = \frac{1}{2}mv^2$[/tex]
So we have:
[tex]$v^2 = \frac{2K}{m}$$\frac{1}{2}K = -\frac{q^4}{6\pi\epsilon_0 m^2 c^3}B^2\int_{0}^{t}\frac{2K}{m}dt$[/tex]
Simplifying:
[tex]$\frac{1}{2}K = -\frac{q^4B^2}{3\pi\epsilon_0 m^3 c^3}Kt$[/tex]
[tex]$t = \frac{m^3c^3}{2q^4B^2\pi\epsilon_0}\frac{1}{K}$[/tex]
Now we can substitute the given values to find t:
[tex]$t = \frac{(9.11\times10^{-31}\ kg)^3(2.998\times10^8\ m/s)^3}{2(1.602\times10^{-19}\ C)^4(7.0\ T)^2\pi(8.85\times10^{-12}\ C^2/N\cdot m^2)}\frac{1}{K}$[/tex]
Assuming an electron mass of 9.11×10−31 kg and a charge of 1.602×10−19 C, we have:
[tex]$t = \frac{2.15\times10^{-41}}{K}\ s$[/tex]
Therefore, the time it takes for an electron to radiate away half its energy while spiraling in a 7.0 T magnetic field is:
[tex]$t = \frac{2.15\times10^{-41}}{0.5K}\ s = \frac{4.30\times10^{-41}}{K}\ s$[/tex]
Learn more about electromagnetic waves visit: brainly.com/question/13874687
#SPJ4
A particle with a charge of -5.00 C is initially moving with velocity v = (1.00 i + 7.00h) m/s. If you encounter a magnetic field B = 10.00 T, determine the vector of the magnetic force on the particle.
A) (-350î - 50.0ņ)
B) (350î - 50.0f)
C)(350i + 50.0h)
D) (-350î + 50.0ỉ)
The vector of the magnetic force on the particle is (350î - 50.0ĥ) N, which corresponds to option (B).
The magnetic force on a charged particle moving in a magnetic field is given by the equation F = q(v x B), where q is the charge, v is the velocity vector of the particle, and B is the magnetic field vector. Here, q = -5.00 C, v = (1.00 î + 7.00 ĥ) m/s, and B = 10.00 T along the z direction.
Taking the cross product of v and B, we get v x B = (-7.00 x 10.00) î + (1.00 x 10.00) ĥ, or (-70.00 î + 10.00 ĥ) Tm/s.
Multiplying this by the charge q, we get F = (-5.00 C) (-70.00 î + 10.00 ĥ) Tm/s, or (350.00 î - 50.00 ĥ) N.
To know more about magnetic field vector click on below link:
https://brainly.com/question/3190862#
#SPJ11
what radius (in m) circular path does an electron travel if it moves at 7.60 ✕ 106 m/s perpendicular to a magnetic field of 0.870 t?
The correct answer is the radius of the circular path of electron travels is approximately 3.25 × 10^-4 meters.
To calculate the radius of the circular path an electron travels in a magnetic field, we can use the formula:
r = mv / (qB)
where r is the radius, m is the mass of the electron, v is its velocity, q is its charge, and B is the magnetic field strength.
The mass of an electron (m) is approximately 9.11 × 10^-31 kg,
its charge (q) is approximately -1.60 × 10^-19 C,
the velocity (v) is given as 7.60 × 10^6 m/s, and
the magnetic field strength (B) is 0.870 T.
Plugging these values into the formula:
r = (9.11 × 10^-31 kg)(7.60 × 10^6 m/s) / ((-1.60 × 10^-19 C)(0.870 T))
The negative sign in the charge value doesn't affect the radius calculation since we're only interested in the magnitude of the radius, so we can ignore it.
r ≈ (9.11 × 10^-31 kg)(7.60 × 10^6 m/s) / ((1.60 × 10^-19 C)(0.870 T))
r ≈ 3.25 × 10^-4 m
To know more about radius of the circular path here
https://brainly.com/question/18456035
#SPJ11
determine the total resistance of the circuit if r1=40, r2=62, r3=34
The total resistance of the circuit is 136Ω if connected in series, and approximately 14.18Ω if connected in parallel.
To determine the total resistance of the circuit with resistors R1, R2, and R3, you need to know if the resistors are connected in series or parallel. I will provide answers for both scenarios.
1. If the resistors are connected in series:
The total resistance (R_total) is simply the sum of the individual resistances:
R_total = R1 + R2 + R3
R_total = 40Ω + 62Ω + 34Ω
R_total = 136Ω
2. If the resistors are connected in parallel:
To calculate the total resistance for parallel-connected resistors, you can use the formula:
1/R_total = 1/R1 + 1/R2 + 1/R3
1/R_total = 1/40Ω + 1/62Ω + 1/34Ω
1/R_total ≈ 0.025 + 0.0161 + 0.0294
1/R_total ≈ 0.0705
Now, take the reciprocal to find R_total:
R_total ≈ 1/0.0705
R_total ≈ 14.18Ω
learn more about total resistance Refer: https://brainly.com/question/16465349
#SPJ11
Two students are conducting an experiment in which they are trying to find a relationship between
the angle of incline of a ramp and the final speed a car reaches when rolling down the ramp. In
order to collect their data, the students must determine the final speed of the car at the bottom of
the ramp. The students discuss how they should determine this speed.
Student 1: "We need to measure the length of the ramp and the time it takes the car to roll down it.
Then we can divide the total distance by the total time to find the final speed."
What is wrong with Student 1's method for determining final speed?
1) This method does not account for the height of the ramp.
2) This method does not take into account the angle of the ramp.
3) This method will determine the acceleration, not the final speed.
4) This method will only determine the average speed, not the final speed.
This method will only determine the average speed, not the final speed. This is wrong with Student 1's method for determining final speed.
Speed is a rate of change of distance with respect to time. i.e. v =dx÷dt. Speed can also be defined as distance over time i.e. speed= distance ÷ time it is denoted by v and its SI unit is m/s. it is a scalar quantity. i.e. it has only magnitude not direction. ( velocity is a vector quantity, it has both magnitude and direction. when we define velocity, we should know about its direction) Speed shows how much distance can be traveled in unit time. As speed is scalar quantity it has nothing to do with the direction. student 1 has not considered the height and angle hence it tells about average velocity not the final velocity.
To know more about Speed :
https://brainly.com/question/30462853
#SPJ1.
in an oscillating lc circuit, l = 1.55 mh and c = 4.98 μf. the maximum charge on the capacitor is 2.65 μc. find the maximum current.
The maximum current in the oscillating LC circuit is 183 mA.
In an oscillating LC circuit, the maximum charge on the capacitor and the values of inductance and capacitance are given. We can use the formula Q = CV to find the maximum voltage across the capacitor, which is V = Q/C.
V = \frac{(2.65 \mu C) }{ (4.98 \mu F) }= 0.531 V
The maximum voltage occurs when the capacitor is fully charged and the current is zero. As the capacitor discharges through the inductor, the current increases and reaches a maximum when the capacitor is fully discharged and the voltage across it is zero. The current is given by the formula I = V/L * t, where t is the time it takes for the current to reach its maximum value.
The time period of the oscillation, T, can be found using the formula[tex]T = 2\pi \sqrt{LC)}[/tex]
T = 2\pi \sqrt(1.55 mH * 4.98 \mu F) }= 7.03 \mu s
The time it takes for the current to reach its maximum value is half the time period, t = T/2 = 3.52 μs.
Now we can calculate the maximum current:
I = V/L * t = (0.531 V) / (1.55 mH) * (3.52 μs)
I = 183 mA
learn more about current Refer:https://brainly.com/question/17176550
#SPJ11
A 150 kg. yak has an average power output of 120 W. The yak can climb a mountain 1.2 km high in (a) 25 min (b) 4.1 h (c) 13.3 h (d) 14.7 h.
We know the yak's mass (m) is 150 kg, the height of the mountain (h) is 1.2 km (1200 meters), and the average power output (P) is 120 W. The yak can climb a mountain 1.2 km high in 25 minutes, 4.1 hours, 13.3 hours, or 14.7 hours.
We can calculate the work done using the formula:
Work = Power x Time
We can use this equation to find the work done by the yak to climb the mountain. Once we know the work done, we can use the equation:
Work = Force x Distance
to find the force the yak exerts while climbing the mountain. Finally, we can use the equation:
Force = Mass x Acceleration
to find the acceleration of the yak while climbing the mountain. From there, we can use the equation:
Distance = (1/2) x Acceleration x Time^2
to find the time it takes for the yak to climb the mountain.
(a) For 25 minutes:
Time = 25 minutes = 0.417 hours
Work = Power x Time = 120 W x 0.417 h = 50 J
Force = Work / Distance = 50 J / 1200 m = 0.042 N
Acceleration = Force / Mass = 0.042 N / 150 kg = 0.00028 m/s^2
Distance = (1/2) x Acceleration x Time^2 = (1/2) x 0.00028 m/s^2 x (0.417 h x 3600 s/h)^2 = 1.2 km
So the yak can climb the mountain in 25 minutes.
(b) For 4.1 hours:
Time = 4.1 hours
Work = Power x Time = 120 W x 4.1 h = 492 J
Force = Work / Distance = 492 J / 1200 m = 0.41 N
Acceleration = Force / Mass = 0.41 N / 150 kg = 0.0027 m/s^2
Distance = (1/2) x Acceleration x Time^2 = (1/2) x 0.0027 m/s^2 x (4.1 h x 3600 s/h)^2 = 1.2 km
So the yak can climb the mountain in 4.1 hours.
(c) For 13.3 hours:
Time = 13.3 hours
Work = Power x Time = 120 W x 13.3 h = 1,596 J
Force = Work / Distance = 1,596 J / 1200 m = 1.33 N
Acceleration = Force / Mass = 1.33 N / 150 kg = 0.0089 m/s^2
Distance = (1/2) x Acceleration x Time^2 = (1/2) x 0.0089 m/s^2 x (13.3 h x 3600 s/h)^2 = 1.2 km
So the yak can climb the mountain in 13.3 hours.
(d) For 14.7 hours:
Time = 14.7 hours
Work = Power x Time = 120 W x 14.7 h = 1,764 J
Force = Work / Distance = 1,764 J / 1200 m = 1.47 N
Acceleration = Force / Mass = 1.47 N / 150 kg = 0.0098 m/s^2
Distance = (1/2) x Acceleration x Time^2 = (1/2) x 0.0098 m/s^2 x (14.7 h x 3600 s/h)^2 = 1.2 km
So the yak can climb the mountain in 14.7 hours.
Therefore, the yak can climb a mountain 1.2 km high in 25 minutes, 4.1 hours, 13.3 hours, or 14.7 hours.
Learn more about mass here:
https://brainly.com/question/19694949
#SPJ11
Which term below is the best one to describe the polarization of a wave with phasor electric field given by Ē = (ay – j2 az) e^jk0x (V/m)^2 A. Left-hand circular polarization B. Right-hand circular polarization C. Linear polarization D. Right-hand elliptical polarization E. Left-hand elliptical polarization
The term that best describes the polarization of a wave with a phasor electric field given by Ē = (ay – j2 az) e^jk0x (V/m)^2 is E. Left-hand elliptical polarization.
This is because the electric field vector components are complex and have different magnitudes, which leads to an elliptical polarization, and the negative imaginary component indicates a left-hand rotation.
Elliptical polarization refers to a situation where the electric field vector traces an elliptical path as the wave propagates in space. This can occur when the magnitudes of the two orthogonal components of the electric field are unequal, and they have a phase difference between them.
In the given phasor electric field, the component along the y-axis is ay and the component along the z-axis is -j2az, where j is the imaginary unit. Since the magnitude of ay is not equal to the magnitude of -j2az, the polarization is elliptical.
However, the negative imaginary component -j2az indicates a right-hand rotation, not a left-hand rotation. Therefore, the correct term to describe the polarization of this wave is right-hand elliptical polarization.
To learn more about electric field, refer below:
https://brainly.com/question/30544719
#SPJ11
All else being equal, how can we increase the theoretical maximum efficiency of a turbine. Increase the volume of the fluid Increase the pressure of the fluid Increase the temperature of the fluid. The theoretical maximum doesn't depend on any of these.
To increase the theoretical maximum efficiency of a turbine, you can increase the pressure and/or the temperature of the fluid.
Here's a step-by-step explanation:
1. Increasing the pressure of the fluid: When the pressure of the fluid entering the turbine is increased, it results in a higher pressure difference across the turbine. This leads to greater energy extraction from the fluid, which in turn improves the turbine's efficiency.
2. Increasing the temperature of the fluid: A higher temperature of the fluid entering the turbine increases its energy content. This allows for more energy to be extracted by the turbine, further improving its efficiency.
Remember that while increasing the volume of the fluid might increase the overall power output of the turbine, it won't necessarily increase its efficiency. The theoretical maximum efficiency depends on factors such as fluid pressure and temperature, as well as the design and materials used in the turbine.
To learn more about turbine click here https://brainly.com/question/30559123
#SPJ11
A converging (lens f=+12cm) in contact with a diverging lens gives a combined focal length of +36 cm. calculate the focal length of the diverging lens.
The focal length of the diverging lens is -18 cm.
To find the focal length of the diverging lens, we can use the lens formula for thin lenses in contact:
1/f_combined = 1/f_1 + 1/f_2
where f_combined is the combined focal length of the system, f_1 is the focal length of the converging lens, and f_2 is the focal length of the diverging lens. We are given f_combined = +36 cm and f_1 = +12 cm.
Substitute the given values into the lens formula.
1/+36 cm = 1/+12 cm + 1/f_2
Solve for 1/f_2.
1/f_2 = 1/+36 cm - 1/+12 cm
Calculate 1/f_2.
1/f_2 = 1/36 - 1/12
1/f_2 = (1 - 3)/36
1/f_2 = -2/36
Find the focal length of the diverging lens (f_2).
f_2 = -36 cm / 2 = -18 cm
Therefore -18 cm is the focal length of the diverging lens.
More on focal length: https://brainly.com/question/14104969
#SPJ11
At what orientation angle in degrees relative to the magnetic field direction does the torque of a magnetic dipole have its largest value? A) 0 B) 180, C) 30, D) 45, E) 90
The correct option is E) 90 which determines the orientation angle in degrees relative to the magnetic field direction does the torque of a magnetic dipole have its largest value.
Torques is defined as the cross product of magnetic dipole moment and the magnetic field. The torque (τ) of a magnetic dipole in a magnetic field is given by the equation: τ = μ * B * sin(θ) where μ is the magnetic dipole moment, B is the magnetic field strength, and θ is the orientation angle between the magnetic dipole and the magnetic field direction. The torque is at its largest value when the sine function has its maximum value of 1. This occurs when the orientation angle (θ) is 90 degrees.
To learn more about magnetic dipole click here https://brainly.com/question/15003698
#SPJ11
The correct option is E) 90 which determines the orientation angle in degrees relative to the magnetic field direction does the torque of a magnetic dipole have its largest value.
Torques is defined as the cross product of magnetic dipole moment and the magnetic field. The torque (τ) of a magnetic dipole in a magnetic field is given by the equation: τ = μ * B * sin(θ) where μ is the magnetic dipole moment, B is the magnetic field strength, and θ is the orientation angle between the magnetic dipole and the magnetic field direction. The torque is at its largest value when the sine function has its maximum value of 1. This occurs when the orientation angle (θ) is 90 degrees.
To learn more about magnetic dipole click here https://brainly.com/question/15003698
#SPJ11
• find the induced emf when the current in a 48.0-mh inductor increases from 0 to 535 ma in 15.5 ms
When the current in the inductor increases, the induced EMF will be in the opposite direction of the current flow, and when the current decreases, the induced EMF will be in the same direction as the current flow.
We can use Faraday's Law of Electromagnetic Induction to find the induced EMF (ε) in the inductor:
ε = -L (ΔI/Δt)
where L is the inductance of the inductor, ΔI is the change in current, and Δt is the time interval over which the current changes.
Substituting the given values, we get:
ε = -(48.0 mH) x (535 mA - 0) / (15.5 ms) = -8.28 V
EMF stands for electromagnetic field, which refers to the physical field produced by electrically charged objects in motion. This field is present whenever there is a flow of electric current, and it can be measured using specialized instruments.
Electromagnetic fields are ubiquitous in our environment, generated by everything from power lines to electronic devices to the human body. While these fields are generally considered safe at low levels, there is ongoing debate about the potential health effects of prolonged exposure to high levels of EMF. Some studies have suggested a possible link between long-term exposure to EMF and an increased risk of certain cancers, neurological disorders, and other health problems.
To learn more about EMF visit here:
brainly.com/question/16626131
#SPJ4
Complete Question:-
Find the induced emf, when the current in a 48.0 mH inductor increases from 0 to 535 mA in 15.5ms.
a bullet with the mass of 2.34g moves at a speed of 1.50x10^3 m/s. if a baseball of mass 145g has the same momentum as the bullet, what is its speed in m/s(a) What must the baseball's speed be if the pitcher's claim is valid?m/s(b) Which has greater kinetic energy, the ball or the bullet?The bullet has greater kinetic energy.Both have the same kinetic energy. The ball has greater kinetic energy.
The baseball's speed must be 24.21 m/s if the pitcher's claim is valid. The bullet has greater kinetic energy.
To find the baseball's speed with the same momentum as the bullet, we can follow these steps:
1. Calculate the momentum of the bullet using the formula:
momentum = mass x velocity.
2. Calculate the speed of the baseball using the formula:
speed = momentum / mass.
(a) To calculate the baseball's speed:
1. Bullet's mass = 2.34 g = 0.00234 kg (convert to kilograms by dividing by 1000)
Bullet's speed = 1.50 x 10³ m/s
Bullet's momentum = mass x velocity = 0.00234 kg * 1.50 x 10³ m/s = 3.51 kg*m/s
2. Baseball's mass = 145 g = 0.145 kg
Baseball's speed = momentum / mass = 3.51 kg*m/s / 0.145 kg = 24.21 m/s
(b) To determine which has greater kinetic energy, we can use the formula:
kinetic energy = 0.5 x mass x (speed²).
1. Bullet's kinetic energy = 0.5 * 0.00234 kg * (1.50 x 10³ m/s)² = 2632.5 J
2. Baseball's kinetic energy = 0.5 * 0.145 kg * (24.21 m/s)² = 42.49 J
Comparing the two kinetic energies, the bullet has greater kinetic energy (2632.5 J) than the baseball (42.49 J).
Learn more about speed:
https://brainly.com/question/13943409
#SPJ11
a 280 g block on a 52.0 cm -long string swings in a circle on a horizontal, frictionless table at 60.0 rpm .
The tension in the string is approximately: 11.48 N.
To determine the tension in the string, follow these steps:
1. Convert the given values to SI units:
- Mass (m) = 280 g = 0.280 kg
- Length of string (L) = 52.0 cm = 0.52 m
- Rotational speed (ω) = 60.0 rpm = 60.0 * (2π rad/min) / 60 s/min = 2π rad/s
2. Calculate the centripetal force acting on the block using the formula F_c = mω²L, where F_c is the centripetal force, m is the mass, ω is the rotational speed, and L is the length of the string:
- F_c = (0.280 kg) * (2π rad/s)² * (0.52 m)
- F_c ≈ 11.48 N
In this scenario, the tension in the string is equal to the centripetal force, as the block is moving in a horizontal circle on a frictionless table.
To know more about "Centripetal force" refer here:
https://brainly.com/question/11324711#
#SPJ11
If a 1000lb load cell has a sensitivity of 3.5 mV/V, what is its maximum output if the excitation voltage is 10 V (answer in mV)?
The maximum output of a 1000lb load cell with a sensitivity of 3.5 mV/V and an excitation voltage of 10 V is 35 mV.
To calculate the maximum output, follow these steps:
1. Identify the load cell's sensitivity: 3.5 mV/V.
2. Identify the excitation voltage: 10 V.
3. Multiply the sensitivity by the excitation voltage: 3.5 mV/V * 10 V = 35 mV.
This calculation determines the maximum output of the load cell when it experiences the full capacity of 1000lb, given its sensitivity of 3.5 mV/V.
The excitation voltage is the electrical input that powers the load cell, and the sensitivity reflects how much the output voltage changes per volt of excitation voltage. In this case, the output increases by 3.5 mV for every volt of excitation, resulting in a maximum output of 35 mV when the excitation voltage is 10 V.
To know more about excitation voltage click on below link:
https://brainly.com/question/14820417#
#SPJ11
a sample that contains 1.8x10^{23} atoms of lead has a mass of blank3 - numeric answer
The mass of a sample containing 1.8x10²³atoms of lead is approximately 61.95 grams.
To find the mass of a sample containing 1.8x10²³atoms of lead, follow these steps:
1. Determine the molar mass of lead (Pb): The molar mass of lead is approximately 207.2 g/mol.
2. Calculate the number of moles in the sample: Since there are 6.022x10²³ atoms in one mole (Avogadro's number), divide the number of atoms in the sample by Avogadro's number:
(1.8x10²³ atoms) / (6.022x10²³atoms/mol) ≈ 0.299 moles.
3. Multiply the number of moles by the molar mass of lead to find the mass:
(0.299 moles) * (207.2 g/mol) ≈ 61.95 g.
The mass of a sample containing 1.8x10²³ atoms of lead is approximately 61.95 grams.
To learn more about mass of an atom https://brainly.com/question/14713405
#SPJ11
State the equations (both data and predicted) for your data.
What would happened to the slope of Applied Force vs. Acceleration for an Atwood's Machine just like the one we used in lab, if the total system mass was increased? a. The slope would have stayed the same because the force required and acceleration measured would change proportionally, leaving a slope the same as before.
b. The slope would have increased because the slope represents the total system mass.
c. The slope would increase because the slope represents the friction in the bearings; and that would increase.
d. The slope would decrease because the same force would give rise to less acceleration thus reducing the slope of F vs. a.
e. The slope would have increased because it would required less force to obtain the same accelerations.
If the total system mass was increased, the slope of Applied Force vs. Acceleration for an Atwood's Machine just like the one we used in lab would decrease because the same force would give rise to less acceleration thus reducing the slope of F vs. a (Option D).
The slope would decrease because the total system mass includes the mass of the hanging masses and the pulley, which would increase if the total system mass was increased. As a result, the force required to move the system would also increase, but the acceleration would decrease due to the increased mass, resulting in a decreased slope of the Applied Force vs. Acceleration graph.
Learn more about Applied Force vs. Acceleration: https://brainly.com/question/964259
#SPJ11
A 5.10-kg watermelon is dropped from rest from the roof of a 21.0-m -tall building and feels no appreciable air resistance.
Calculate the work done by gravity on the watermelon during its displacement from the roof to the ground.
Just before it strikes the ground, what is the watermelon's kinetic energy?
Just before it strikes the ground, what is the watermelon's speed?
The watermelon has a kinetic energy of 1054 J and a speed of 20.4 m/s just before it hits the ground.
To solve this problem, we can use the work-energy theorem, which states that the net work done on an object is equal to its change in kinetic energy. Since the watermelon is dropped from rest, its initial kinetic energy is zero, and we can find the work done by gravity to calculate its final kinetic energy and speed just before it hits the ground.
First, we need to find the gravitational potential energy of the watermelon when it is on the roof of the building, which is given by:
PE = mgh
where m is the mass of the watermelon, g is the acceleration due to gravity (9.81 m/s²), and h is the height of the building (21.0 m).
Substituting the given values, we get:
PE = (5.10 kg)(9.81 m/s²)(21.0 m) = 1054 J
This is the amount of potential energy the watermelon has on the roof. As it falls, this potential energy is converted into kinetic energy, and we can use the work-energy theorem to find the final kinetic energy just before it hits the ground. The work done by gravity is equal to the negative of the change in potential energy, or:
W = -ΔPE = -PE_final + PE_initial
where PE_initial is the potential energy of the watermelon on the roof and PE_final is its potential energy just before it hits the ground (which is zero). Substituting the values, we get:
W = -(0 J - 1054 J) = 1054 J
This is the work done by gravity on the watermelon as it falls from the roof to the ground. According to the work-energy theorem, this work is equal to the change in kinetic energy of the watermelon:
W = ΔKE = KE_final - KE_initial
Since the watermelon is dropped from rest, its initial kinetic energy is zero, so we can solve for the final kinetic energy:
KE_final = W + KE_initial = 1054 J + 0 J = 1054 J
This is the final kinetic energy of the watermelon just before it hits the ground. Finally, we can use the equation for kinetic energy to find the speed of the watermelon just before it hits the ground:
KE_final = 1/2 mv²
Solving for v, we get:
v = (2KE_final/m) = (2(1054 J)/(5.10 kg)) = 20.4 m/s
learn more about kinetic energy here:
https://brainly.com/question/26472013
#SPJ11
A spaceship measures bright flashes of light from a distant star. The spacecraft now heads toward the star at 0.90c.
From the spacecraft's point of view, at what speed do the pulses approach? Express your answer with the appropriate units.
The speed of light stays at c from the perspective of the spaceship. As a result, the light pulses continue to travel towards the spacecraft at the speed of light, or around 299,792,458 m/s.
What issue was resolved by special relativity?Yet when he did, in 1915, it fundamentally altered our understanding of the cosmos. Space and time are not fixed concepts; rather, they are a single entity, as demonstrated by special relativity.
What issues does the theory of relativity have?Other theories, disapproval of the abstract mathematical method, and purported flaws in the theory have all been used as justifications for criticism of the theory of relativity. Several authors claim that these critiques occasionally included antisemitic arguments against Einstein's Jewish origin.
To know more about speed visit:-
https://brainly.com/question/15837674
#SPJ1
ort the layers of a dying high mass star, beginning with the outermost layer
Drag and drop to order
1
A
Helium fusion shell
2
B
Magnesium fusion shell
3
C
Oxygen fusion shell
4
D
Carbon fusion shell
5
E
Neon fusion shell
6
F
Iron core
7
G
Silicon burning shell
8
H
Hydrogen outer layer
9
I
Hydrogen fusion shell
The layers of a dying high mass star, beginning with the outermost layer, are: Hydrogen outer layer (H), Hydrogen fusion shell (I), Helium fusion shell (A), Carbon fusion shell (D), Neon fusion shell (E), Oxygen fusion shell (C), Silicon burning shell (G), Iron core (F), Magnesium fusion shell (B).
The layers of a dying high mass star are formed as a result of different fusion processes occurring in the star's core. The outermost layer is the Hydrogen outer layer (H), which is composed of mostly hydrogen gas. Inside the Hydrogen outer layer is the Hydrogen fusion shell (I), where hydrogen fusion takes place, converting hydrogen into helium.
Next comes the Helium fusion shell (A), where helium fusion occurs, converting helium into heavier elements like carbon and oxygen. After the Helium fusion shell comes the Carbon fusion shell (D), where carbon fusion takes place, converting carbon into heavier elements like neon and oxygen.
The Neon fusion shell (E) comes after the Carbon fusion shell, followed by the Oxygen fusion shell (C), where oxygen fusion takes place, converting oxygen into heavier elements like silicon. The Silicon burning shell (G) comes after the Oxygen fusion shell, where silicon is fused into heavier elements like iron.
At the center of the star lies the Iron core (F), which is the result of the fusion of all the lighter elements. Finally, the outermost layers of the star collapse onto the Iron core, triggering a supernova explosion.
The Magnesium fusion shell (B) lies between the Helium and Carbon fusion shells and is responsible for the production of heavier elements like magnesium.
For more questions like Fusion click the link below:
https://brainly.com/question/12701636
#SPJ11
Three very long, straight wires lie at the corners of a square of side , as shown in the figure. The currents in the three wires have the same magnitude , but the two diagonally opposite currents are directed into the screen while the other one is directed out of the screen.
1. Derive an expression for the magnitude of the magnetic field at the fourth corner of the square. (Give an exact answer. Use symbolic notation and fractions where needed. Let 0 represent the permeability of free space.)
2. Determine the direction θ of the magnetic field at the fourth corner of the square, measured counterclockwise from the positive x-axis.
1. The magnitude of the magnetic field at the fourth corner of the square is 0I/2π.
2. the direction θ of the magnetic field at the fourth corner of the square is counterclockwise from the positive x-axis.
What is magnetic field?It is an invisible force field that can attract or repel other magnetic objects. Magnetic fields are created by the motion of electric charges and are measured in units of gauss or tesla.
1. The magnitude of the magnetic field at the fourth corner of the square can be determined using the equation
B = μoI/2πr, where μo is the permeability of free space (0), I is the current in each wire, and r is the distance between two wires.
In this case, the distance between two wires is , so the equation can be simplified to B = 0I/2π.
Therefore, the magnitude of the magnetic field at the fourth corner of the square is 0I/2π.
2. The direction θ of the magnetic field at the fourth corner of the square can be determined by examining the directions of the currents in the three wires.
Since the two diagonally opposite currents are directed into the screen and the other one is directed out of the screen, it can be inferred that the direction of the magnetic field at the fourth corner of the square is counterclockwise from the positive x-axis.
Therefore, the direction θ of the magnetic field at the fourth corner of the square is counterclockwise from the positive x-axis.
For more questions related to permeability
https://brainly.com/question/30465853
#SPJ1
a wheel of diameter 21.0 cm has a 10.0 m cord wrapped around its periphery. starting from rest, the wheel is given a constant angular acceleration of 3 rad/s2. A) through what angle must the wheel turn for the cord to unwind completely?B) How long will this take? (ans 13.7s)
A) The angle the wheel must turn for the cord to unwind completely is 95.2 radians.
B) The time it will take is 13.7 seconds.
A) To find the angle through which the wheel must turn for the cord to unwind completely, we first need to find the wheel's circumference. The circumference (C) can be calculated using the formula:
C = π * D
where D is the diameter of the wheel. In this case, D = 21.0 cm.
C = π * 21.0 cm = 66.0 cm
Since the cord is 10.0 m long, we need to convert the wheel's circumference to meters:
C = 0.66 m
Now, we can find how many rotations the wheel makes by dividing the length of the cord by the circumference of the wheel:
Rotations = Cord length / Circumference = 10.0 m / 0.66 m = 15.15 rotations
To find the angle through which the wheel turns, we multiply the number of rotations by 2π:
Angle (θ) = 15.15 rotations * 2π radians = 95.2 radians
B) To find how long this takes, we'll use the following equation for angular motion:
θ = ω₀ * t + 0.5 * α * t²
where ω₀ is the initial angular velocity (0 rad/s, since it starts from rest), α is the angular acceleration (3 rad/s²), and t is the time. We already calculated the angle (θ) as 95.2 radians.
Plugging in the known values:
95.2 = 0 * t + 0.5 * 3 * t²
Solving for t:
t² = 95.2 / 1.5
t² = 63.47
t = √63.47
t ≈ 13.7 seconds
So it will take approximately 13.7 seconds for the cord to unwind completely.
Learn more about angular motion here: https://brainly.com/question/29342095
#SPJ11
Use the following scenario to answer the next three questions. A 2,000-kg truck moves with a velocity of 20 m/s. The driver applies brakes at the bottom of a 12- meter high hill. The truck comes to a stop at the top of the hill. (I know the picture says 10 m, but use 12 m. Thanks) Use g=9.8 m/s? or g=10m/s2 for the acceleration due to gravity. what is the truck's total mechanical energy at the bottom of the hill before the driver applies the brakes?
The truck's total mechanical energy at the bottom of the hill before the driver applies the brakes is 400,000 Joules.
To find the total mechanical energy of the truck at the bottom of the hill before the driver applies the brakes, we need to calculate both its kinetic energy (KE) and potential energy (PE). We can then add the two energies to get the total mechanical energy (TME).
Calculate kinetic energy (KE):
KE = 0.5 × mass × velocity²
KE = 0.5 × 2000 kg × (20 m/s)²
KE = 0.5 × 2000 kg × 400 m²/s²
KE = 400,000 J (joules)
Calculate potential energy (PE) at the bottom of the hill:
Since the truck is at the bottom of the hill, its height is 0 meters. Therefore, its potential energy is also 0.
PE = mass × gravity × height
PE = 2000 kg × 9.8 m/s² × 0 m
PE = 0 J (joules)
Calculate the total mechanical energy (TME):
TME = KE + PE
TME = 400,000 J + 0 J
TME = 400,000 J
So, 400,000 Joules is the truck's total mechanical energy at the bottom of the hill before the driver applies the brakes.
More on energy: https://brainly.com/question/28810902
#SPJ11
A distant star has a single planet circling it in a circular orbit of radius 4.25 * 10 ^ 11 m. The period of the planet's motion about the star is 765 day. The universal gravitational constant is 6.67259*10^ -11 N overline m ^ 2 / k * g ^ 2. What is the mass of the star? Answer in units of kg.
AThe mass of star is 2.18*10³⁰ kg.
The mass of the star can be calculated using the formula: M = (4π²r³)/(G T²), where M is the mass of the star, r is the radius of the orbit, T is the period of the orbit, and G is the universal gravitational constant.
Plugging in the given values, we get M = (4π²(4.25*10¹¹)³)/(6.67259*10⁻¹¹(765)²) = 2.18*10³⁰ kg.
The given information allows us to use Kepler's Third Law, which states that the square of the period of a planet's orbit is proportional to the cube of its average distance from the star. Using this law, we can relate the period and radius of the orbit to the mass of the star.
By rearranging the formula and plugging in the given values, we can solve for the mass of the star. The universal gravitational constant is used to convert the units of the given values to the units needed for the formula. The resulting mass of the star is very large, as expected for a star with a planet in orbit around it.
To know more about Kepler's Third Law click on below link:
https://brainly.com/question/1608361#
#SPJ11
A 1.75-m-tall person stands 8.30 m in front of a large, concave spherical mirror having a radius of curvature of 5.40 m.(a) Determine the mirror's focal length (in m).m(b) Determine the image distance (in m).m(c) Determine the magnification.
A) According to the question, the focal length is the radius of the mirror is 3.63 m, b) Using the mirror equation, the image distance is 16.45 m, c) The magnification of the mirror is -1.98.
What is radius?Radius is a network protocol used to authenticate, authorize and manage network access. It is usually used in conjunction with a Remote Authentication Dial-In User Service (RADIUS) server.
a) The mirror's focal length is given by 1/f = 1/R + 1/d, where R is the radius of curvature and d is the distance from the mirror to the object. Thus, the focal length of the mirror is f = 5.40 m/(1/5.40 + 1/8.30) = 3.63 m.
b) The image distance is the distance from the mirror to the image of the object. Using the mirror equation, the image distance is d = 5.40 m/(1/5.40 - 1/8.30) = 16.45 m.
c) The magnification is given by M = -d_i/d_o, where d_i is the image distance and d_o is the object distance. Thus, the magnification of the mirror is M = -16.45/8.30 = -1.98. This means that the image is inverted and about twice as tall as the object.
To learn more about radius
https://brainly.com/question/30145509
#SPJ1
calculating your body surface area based on dubois formula and estimate your current rate of dry heat exchange
Assuming an average BMR of 1500-2000 kcal/day for a sedentary adult, the corresponding rate of dry heat exchaexchaaexchangengengengeaexchangengengenge would be in the range of 100-130 watts.
The Dubois formula is commonly used to estimate body surface area (BSA) based on height and weight:
BSA (m^2) = 0.20247 x height (m)^0.725 x weight (kg)^0.425
To estimate your rate of dry heat exchange, you would need to know your basal metabolic rate (BMR) and the environmental conditions you are currently in. BMR is the amount of energy your body burns at rest to maintain its basic functions such as breathing, circulating blood, and keeping your organs functioning. The rate of dry heat exchange depends on the difference between your body temperature and the temperature of your surroundings, as well as the amount of exposed skin and the insulating properties of your clothing.
Assuming an average BMR of 1500-2000 kcal/day for a sedentary adult, the corresponding rate of dry heat exchange would be in the range of 100-130 watts. However, this is a very rough estimate and the actual rate of dry heat exchange can vary greatly depending on individual factors and environmental conditions.
Visit to know more about BMR:-
brainly.com/question/18093573
#SPJ11