can someone please help me with this. thank u ❤️​

Can Someone Please Help Me With This. Thank U

Answers

Answer 1

answer:projectile motion

Explanation:

Since gravity acts vertically, there is no acceleration in the horizontal (x) direction. This special type of two-dimensional motion is called projectile motion.

Answer 2

Answer:

.......................


Related Questions

Q1. What is the mass of a ball that has a kinetic energy of16 J and it is traveling at 4 m/s?
Q2. What is the kinetic energy of a soccer ball which has a mass of 1 kg and is kicked with a velocity of 10 m/s?
Q3.exercise ball is on a table 2 m above the ground. What is the mass of the ball if it has a GPE of 40 ?
Q4.What is the gravitational potential energy (GPE) of a 2 kilogram book that is 20 meter above the ground?

Answers

Answer:

Explanation:

Kinetic Energy has a formula of

[tex]KE=\frac{1}{2}mv^2[/tex] and

Potential Energy has a formula of

PE = mgh. The first 2 problems use the KE formula and the next 2 use the PE formula.

Q1. KE = 16 and v = 4 m/s:

[tex]16=\frac{1}{2}m(4)^2[/tex] and

[tex]\frac{2(16)}{16}=m[/tex] so

m = 2 kg

Q2. mass = 1 kg and v = 10 m/s:

[tex]KE=\frac{1}{2}(1)(10)^2[/tex] so

KE = 50 J

Q3. PE = 40, h = 2, g = 9.8:

40 = m(9.8)(2) and

[tex]\frac{40}{(9.8)(2)}=m[/tex] so

m = 2.0 kg

Q4. mass = 2 kg, g = 9.8 m/s/s, h = 20:

PE = 2(9.8)(20) so

PE = 392 J

**I completely disregarded the rules for sig fig's because your numbers were very inexact**

Calculate the kinetic energy of a car of mass 800kg moving at 100 kmph.

Answers

Answer:

KE = 308642.02469136 J

16) A man ran a 5 mile race. The race looped around a city park and back
to the starting line. What is the man's total displacement? *

Answers

Answer:

The man's total displacement is equal to 0.

Explanation:

Given that,

A man ran a 5 mile race. The race looped around a city park and back  to the starting line.

We need to find the total displacement of the man.

We know that,

Displacement = shortest path covered

Also,

Displacement = final position - initial position

As it reaches back to its starting line, it means, the displacement is equal to 0.

Hence, the man's total displacement is equal to 0.

a cylinder has volume 50 cm and radius 4 cm find its volume. pls do it with the full process ​

Answers

Explanation:

Please, check the question properly

If a 2.0Ω resistor and a 4.0Ω resistor are connected with a 12 volt battery, what is the total resistance of the circuit?
4.8Ω
9.2Ω
6.0Ω
1.3Ω

Answers

Series:
R = 2 + 4 = 6

Parallel:
R = 1/2 + 1/4 = 0.75

I am assuming this is in series since the parallel answer isn’t up there. The voltage doesn’t help us determine total resistance.

Someone HELP if the displacement is in the start and it ends in the same spot then would It be 0?

Answers

Answer:

Yes

Explanation:

Displacement is equal to the final position of X minus the initial position of X.

The diameter of a copper wire is thought to be approximately 0.3mm. Which instrument should be used to obtain a more accurate measurement of the diameter of the wire? A measuring tape B metre rule C micrometer D ruler 2

Answers

Answer:

C

Explanation:

The correct answer should be the micrometer.

The micrometer is an instrument that is capable of measuring the component of an object to very high precision. It is used to obtain accurate measurements in engineering.

In the case of the copper wire, the diameter of 0.3 mm was an approximation and a more accurate measure of the diameter would be obtained by using the micrometer.

The correct option is C.

Can you anser the two questions fast

Answers

Answer:

yes! what are the questions??

Explanation:

Please help !!! anyone​

Answers

(If you don’t understand, I will try to explain to you again!)

Se tiene un péndulo cuyo frecuencia de oscilación es de 0.4 Hz. Cual sera la frecuencia de oscilacion de otro péndulo cuya longitud es el triple del anterior

Answers

Answer:

f = 0.365 Hz

Explanation:

The angular velocity of a simple pendulum is

           w = [tex]\sqrt{g/L}[/tex]

angular velocity and frequency are related

           w = 2π f

we substitute

           2π f = [tex]\sqrt{g/L}[/tex]

Let's find the initial length of the pendulum

            L = [tex]\frac{g}{4\pi^2 } \ f_o[/tex]

            L₀ = [tex]\frac{9.8}{4 \pi ^2} \ 0.4[/tex]

            L₀ = 0.6206 m

Indicates that the length of the chord triples

             L = 3 L₀

             L = 3 0.6206

             L = 1.8618 m

let's find the frequency

             f = [tex]\frac{1}{2\pi } \ \sqrt{\frac{9.8}{1.8618} }[/tex]

             f = 0.365 Hz


An object is placed closer to the lens than f for a diverging lens. The image will be located:
a) between f and 2f

b) between the lens and f

c) A or B or C

d) farther than 2f

Answers

It’s b i took the test

the quantum theory of radiation reflects:

the principle of superposition
the electromagnetic theory of light
the special theory of relativity
the principle of the photoelectric effect ​

Answers

Answer:

The electromagnetic theory of light , that's the answer

Answer:

the electromagnetic theory of light

Explanation:

got it right on o.w

Describe the effect of the mass on the net force.

Answers

Answer:

F = m a

it means as m increase force increase also and acceleration is constant

the best example of this case is free fall regardless of the mass of something the free fall acceleration is constant - 9.81 m/s^2, because as mass increase gravitational force increase also

Answer:

hlw I'm jess bregoli

your answer is here (◕ᴗ◕✿)

mass is the amount of matter..Gravity affects weight, it does not affect mass.

Masses always remain the same.

Explanation:

hope it may help you

pleaseeeeeee helppppp this is mah last question... thank u (. ^ ᴗ ^. )​

Answers

Answer:

44.1 m

Explanation:

Consider the displacement being x:

x = (g•t²)/2

x = (9.8•3²)/2

x = (9.8•9)/2

x = 88.2/2

x = 44.1 m

Answer:

44.1 m

Explanation:

that's the correct answer

If a train traveled 400 miles north and traveled back 275 miles south and the total trip took 5 hours to complete, what was the average velocity of the train in mph?

Answers

The average velocity is 25 mph north.

Average velocity = displacement/time

Displacement =

(400 mi north) + (275 mi south)

Displacement = 125 mi north

Average V = (125 mi north) / 5 hours.

Average V = 25 mph north

A student is in class 400 minutes every day for 5 days each week. How many seconds is this?

Answers

Answer:

120,000seconds

Explanation:

400 minutes x 5= 2000minutes (2000minutes x 60)seconds =120,000seconds.

btw :

stay safe! :3

Answer:

12000

Explanation:

5 x 400 = 2000, 2000 x 60 = 12000

How sun directly overhead effects climate?

Answers

Answer:

The amount of heat energy received at any location on the globe is a direct effect of Sun angle on climate, as the angle at which sunlight strikes Earth varies by location, time of day, and season due to Earth's orbit around the Sun and Earth's rotation around its tilted axis.

Answer:

The earth's climate system depends entirely on the sun for its energy. Solar radiation warms the atmosphere and is fundamental to atmospheric composition.

Explanation:

hope this helps :)

HELP ME PLEASE I NEED IT NOW
a) What is the value of the angle of incidence of Ray PQ on the mirror AB?

Answers

Answer:

the angle of incident is 40°

Explanation:

NQ is the normal to the mirror, therefore

angle NQA =90°

PQA = 50°

incident angle = NQA - PQA

90°- 50° = 40°

note that the angle of reflection is equal to the angle of incident

HELP ME PLEAASEEE ILL MARK U THE BRAINLIEST

Answers

Answer:

D.

[tex]impulse = force \times time \\ = 60 \times 10 \times 20 \\ = 12000 \: kgm {s}^{ - 1} [/tex]

Option C: 60 mass of child/kg & 10 time / s

hope this helps :)

In a few sentences, describe how the thermostat utilizes a bimetallic strip in order to turn a furnace on and off in one or two sentences.

Answers

Answer:

Explanation:

Bimetallic strips are used in thermostats for measuring and controlling temperature. The strip is connected to a switch and as the temperature changes, the strip flexes and opens or closes a contact. They are also used in ovens for measuring temperature. An electromechanical thermostat typically contains either a bi-metal coil or a metal strip. When the temperature changes, this coil or strip will move, causing a vial containing mercury to tip to one side. The mercury flows to one end of the vial, signaling that the heating or cooling needs to be turned on.

A 5.00 kg pendulum swings back and forth. At the top of its arc it reaches a height of 0.36 m. What is the velocity of the pendulum at the top of the arc?

0 m/s
7.2 m/s
2.7 m/s

Answers

Answer:

Gravitational potential energy = (mass) x (gravity) x (height)

Kinetic energy (of a moving object) = (1/2) (mass) x (speed)²

When the pendulum is at the top of its swing, its potential energy is

(mass) x (gravity) x (height)

= (5 kg) x (9.8 m/s²) x (0.36 m)

= (5 x 9.8 x 0.36) joules

17.64 joules .

Energy is conserved ... it doesn't appear or disappear ... so that number is exactly the kinetic energy the pendulum has at the bottom of the swing, only now, it's kinetic energy:

17.64 joules = (1/2) x (mass) x (speed)²

17.64 joules = (1/2) x (5 kg) x (speed)²

Divide each side by 2.5 kg:

17.64 joules / 2.5 kg = speed²

Write out the units of joules:

17.64 kg-m²/s² / 2.5 kg = speed²

(17.64 / 2.5) (m²/s²) = speed²

7.056 m²/s² = speed²

Take the square root of each side: Speed = √(7.056 m²/s²) = 2.656 m/s.

Looking through the choices, we're overjoyed to see that one if them is ' 2.7 m/s '. Surely that's IT !

Hope this will help you ...

Calculate the electric potential at point A, the middle of the rectangle, and at point B, the middle of the right-hand side of the rectangle. How would you find the electric potential?

Answers

Answer:

With the help of formula.

Explanation:

We can calculate the electric potential of any point through the formula of electric potential which is given below.

Electric potential =  Coulomb constant x charge/ distance of separation.

Symbolically it can be written as,  V = k q/ r where

V = electric potential  

k = Coulomb constant

q = charge

r = distance of separation

If we have all these data, we can simply put the data in the formula and we will get the value of electric potential.

Which of the following describes the work done by a heat engine?
A. Qin - Qout
B. Qin - W
C. Qout - Qin D. Qin + Qout

Answers

Answer: A.

Explanation:

Máquina térmica tem como função, manter a temperatura de um dado fluído, então, a quantidade de calor desse mesmo fluído ao entrar na máquina, será igual á quantidade de calor desse fluido saindo.

Qin - Qout describes the work done by a heat engine. Hence option A is correct.

What is heat engine ?

A heat engine is a system which converts heat into useful work. Carnot engine is  an ideal engine which has maximum efficiency than any other engines. Carnot has showed that "no engine can be more efficient than Carnot engine and the 100% efficient engine can not be existed". It takes heat from the reservoir to do some work and it discharges some amount of heat to the sink. Reservoir is know as hot body and sink is know as cold body.

Efficiency of the Carnot's heat engine is given by,

Efficiency, η = Work done / Heat input

Work done, W = Q1 – Q2

Heat input = Q1

Efficiency,

η = W / Q1

= (Q1 – Q2) / Q1

=1 – (Q2 / Q1).

To have engine with 100% efficiency, Q2 must be zero and it is not possible.

Hence work done by a heat engine is Qin - Qout.

To know more about heat engine, click :

https://brainly.com/question/28034387

#SPJ7.

 

Qué tipo de onda tiene mayor velocidad: Onda mecánica en un sólido Onda electromagnética Onda mecánica en el aire

Answers

Answer:

Onda electromagnética

Explanation:

Las ondas mecánicas requieren un medio material para la propagación, mientras que las ondas electromagnéticas no requieren un medio material para la propagación.

Generalmente, las ondas electromagnéticas se mueven con una velocidad muy alta.

Todas las ondas electromagnéticas se denominan colectivamente luz y tienen una velocidad común de 3 × 10 ^ 8 m / s en el aire.

Ninguna onda mecánica tiene una velocidad tan alta en el aire.

To add to the complexity, those precious atoms face the peril of disintegrating into the void. Luckily, by now, they are feeling the influence of gravity to bring them safely together. Based on this sentence, the reader can infer that — A There was no gravity at the time of the Big Bang. B The most basic atoms were formed due to the force of gravity. C Gravity developed right after the first atoms fell apart. D The force of gravity helped collapse the newly created atoms.

Answers

Answer:

B The most basic atoms were formed due to the force of gravity.

Explanation:

Since the statement says that the atoms could have faced the peril of disintegrating into the void, this means that, they could have been destroyed by movement away into the void.

But, it also says that by now, they are feeling the influence of gravity to bring them safely together. This statement shows that gravity brings them (the atoms) together and thus doesn't allow them disintegrate into the void.

So, a reader can thus infer that the most basic atoms were formed due to the force of gravity since it doesn't allow the atoms disintegrate into the void.

So, B is the answer.


If you want to decrease the current created by a generator what can you do?

Answers

Answer:

To decrease the current;

1) Use fewer loops or number of turns

2) Use a lower speed of rotation of the coil in the magnetic field

3) Use a weaker magnetic

Explanation:

According to Faraday's Law of induction, which is the basis of the electromagnetism, electromagnetic induction and therefore the basis of the  electric generator, can be written as follows;

[tex]\epsilon = -N \cdot \dfrac{\Delta \phi}{\Delta t}[/tex]

Where;

ε = The induced voltage

N = The number of turns (loops)

ΔФ = The change in the magnetic flux

Δt = The change in the time (the duration)

Given that voltage is directly related to the current, decreasing the voltage, decreases the current

To decrease the voltage, and therefore, the current we can;

1) Reduce the number of loops in the coil

2) Increase the time change per unit change in flux by slowing down the speed of rotation of the generator

3) Decrease the amount of change in the magnetic field per turn, by using a weaker magnetic

8. A 22 g bullet with a speed of 230 m/s is fired in to a tree and comes to rest 23 cm into
the tree
a) Find the work done by the tree to stop the bullet
b) Find the average force exerted by the tree

Answers

Answer:

kinetic energy of 16 J. Determine the velocity of the first toy, and the mass of the ... distance of 12 cm into the tree. ... b) the average force exerted on the bullet while slowing down to a stop.

14 pages·317 KB

What is the gravitational potential energy of a 3.0-kg rock that is 12.4 m above the ground?

Answers

Answer:

Explanation:

PE = mgh where m is mass, g is the pull of gravity, and h is the height to which the object can possibly fall.

PE = 3.0(-9.8)(-12.4) so

PE = 360 J, rounded to the correct number of sig figs.

The gravitational potential energy of the rock is 362.4 joules.

What is gravitational potential energy?

The gravitational potential energy of an object is given by the formula:

PE = mgh

where PE is the potential energy, m is the mass of the object, g is the acceleration due to gravity (which is approximately 9.81 m/s^2 near the surface of the Earth), and h is the height of the object above a reference point.

In this case, the mass of the rock is 3.0 kg, the height above the ground is 12.4 m, and the acceleration due to gravity is 9.81 m/s^2. Substituting these values into the formula, we get:

PE = (3.0 kg) x (9.81 m/s^2) x (12.4 m) = 362.4 J

Therefore, the gravitational potential energy of the rock is 362.4 joules.

To learn about universal gravitation constant click:

https://brainly.com/question/858421

#SPJ3

A carpenter applies a force of 60N horizontally to push a plane 40 cm along a piece of wood, how much work does she do?

Answers

Answer:

W = 24 J

Explanation:

Given that,

Applied force, F = 60 N

Distance moved, d = 40 cm = 0.4 m

We need to find the work done by the carpenter. We know that,

Work done, W = Fd

Put all the values,

W = 60 N × 0.4 m

= 24 J

Hence, the required work done is equal to 24 J.

Which variable is represented by the following symbol? λ
a. Wavelength
b. Amplitude
c. Frequency
d. Velocity

Answers

Answer:

A

Explanation:

Wavelength is represented by lambda

A wavelength is the answer
Other Questions
How does snowball story serve as an allegory for trotskys life 7 pens and 2 pencils cost 223 pens and 4 pencils cost 11Find the cost of a penfind the cost of a pencil Whats one thing that brings you joy? I personally like watching the trees change from winter into fall haha 1. Compare a positive feedback loop and negative feedback loop for homeostasis. Body temperature is an example of a negative feedback loop. Imagine that body temperature was regulated as a positive feedback loop and explain what would happen.2. Look at the figure of the brain lobes in your textbook. Do you think the chimpanzee would have the same brain lobes as that of a human? How might the chimp brain differ from a humans? Keep in mind the chimpanzee is the humans closest relative. Explain (with theories support) the elements that can affect an individual behavior Project A requires a $280,000 initial investment for new machinery with a five-year life and a salvage value of $30,000. The company uses straight-line depreciation. Project A is expected to yield annual net income of $20,000 per year for the next five years. QS 26-6 Accounting rate of return LO P2 Compute Project As accounting rate of return. Use the drop-down menus to complete the steps for creating a subform.1. Open the form in the view.2. Zoom in to make the form easier to see as needed.3. Under Form Design Tools, open the tab.4. Click the Subform/Subreport button.5. Place the cursor at an insertion point, and to create a space for the subform.6. The will open to allow you to add fields.7. Click Finish.ANSWERS: Design, Design Tab, Click and Drag, Subform Wizard Why are mobile apps often easier to develop than desktop apps?mobile apps use a lower screen resolutionmobile apps can be created in C#mobile apps use less memory than desktop appsmobile app creation platforms are available that reduce the need to code Please help me with this question what is the first 50 digitizes of PI On a city street you should be looking ahead as far ahead as the car in front of you. a water main is to be constructed with a 10% grade in the north direction and a 20% grade in the east direction. determine the angle theta required in the water main for the turn from north to east A cylindrical flower vase has a diameter of 6cm and a volume of 171cm^(3) Determine the height of the vase. Someone help I have been stuck on this for 30 min Question 10 of 10 To find the inverse of f(x) = 2x - 1, Patel begins by replacing f(x) with y. He then switches x and y. What is the next step? A. Replace y with f-1(x). B. Subtract 1 from both sides of the equation. C. Solve the equation for y. O D. Solve the equation for x. SUBMIT A motor has an internal resistance of 12.1 . The motor is in a circuit with a current of 4.0 AWhat is the voltage?HELP PLEASE Which is the x-intercept of f(x) = log6(2x) 1? .Why did Dally tell Pony and Johnny not to go near thechurch when they saw it was on fire? In what ways did President Trumans airlift support the foreign policy of containment? The base of triangle M is four times the base of tri-angle N, while the height of triangle N is half theheight of triangle M. The area of triangle M is howmany times that of triangle N ?