Based on the image shown, the numbers that correspond to the term or phrase assuming that the electrons flow counterclockwise from 3 to 2 to 1, from 5 to 4 to 5, and to 3 are:
Anode: 3Cathode: 1Salt bridge: 4Electrolytes: 5Electrode where oxidation occurs: anodeThe reaction that takes place in this cell is spontaneousWhat are electrochemical cells?Electrochemical cells are cells that convert chemical energy to electrical energy.
The components of an electrochemical cell are:
anodecathodeelectrolytesalt bridgeLearn more about electrochemical cells at: https://brainly.com/question/10470515
#SPJ1
A brick is thrown upward from the top of a building at an angle of 10° to the horizontal and with an initial speed of 15 m/s. If the brick is in flight for 2.9 s, how tall is the building? any help would be greatly appreciated
The total height of the building from which the brick is thrown is 33.60 meters.
What is Speed?
Speed is the rate of change of position of an object in any direction with respect to time. Speed is measured as the ratio of distance to the time in which the distance was covered. The SI unit of speed is m/s (meter per second).
The time of flight of the object from the building is:
t = 2μ sinθ/ g
t = 2 × 15 × sin10/ 9.8
t = 30 × 0.175/ 9.8
t = 0.535 seconds
Total time to cover the distance = 2.9 seconds
Total time = 2.9 - 0.535
Total time = 2.365
μg = μ sinθ
h = 15 × sin10 × 2.365 + 1/2 × 9.8 × (2.365)²
h = 2.625 × 2.365 + 1/2 × 9.8 × (2.365)²
h = 6.20 + 4.9 × 5.59
h = 6.20 + 27.40
h = 33.60 meters
Learn more about Speed here:
https://brainly.com/question/28224010
#SPJ1
Mention four factors on which the amount of precipitation intercepted by vegetal cover depend on
Precipitation amount, storm frequency, and severity, storm duration, kind of precipitation, wind during storm, and wind during evaporation are the main precipitation and storm elements that influence interruption loss (Kenneth, 1996).
What does it signify when vegetation blocks precipitation?All procedures that stop rainfall from instantly reaching the soil are referred to as interceptions. The two main ways that vegetation intercepts water are by catching it on leaf surfaces throughout the canopy and by depositing litter on the ground.
Intercepted precipitation: What is it?Precipitation that is intercepted by leaves, plant branches, and the forest floor prevents it from reaching the soil and instead stays on the surface.
To know more about Precipitation visit:-
https://brainly.com/question/29762381
#SPJ1
In the figure below, what is the maximum speed of a 2.0 g particle that oscillates between x = 2.0 mm and x = 8.0 mm?
In the figure below, the maximum speed of a 2.0 g particle that oscillates between x = 2.0 mm and x = 8.0 mm is 63 m/s.
What is oscillation?Periodic or oscillatory motion is defined as a motion that repeats itself. Due to a restoring force or torque, an object in such motion oscillates around an equilibrium position.
Energy is conserved in oscillation.
So, the maximum loss in Potential Energy = Maximum gain in Kinetic energy
5 J - 1 J = Maximum gain in Kinetic energy
Maximum gain in Kinetic energy = 4 J
[tex]0.5 \times m \times vmax^2 = 4\\0.5 \times 2.0 \times 10^-3\; Kg \times vmax^2 = 4 J\\vmax^2 = 4 \times 10^3 m^2/s^2\\vmax = 63.2 m/s[/tex]
Therefore, the maximum speed of a 2.0 g particle that oscillates between x = 2.0 mm and x = 8.0 mm is 63 m/s.
To learn more about oscillation, refer to the link:
https://brainly.com/question/27542934
#SPJ1
The uniform beam has a weight W and length L and is supported by a pin at A and cable BC ( figure 1)
Part A
Determine the horizontal and vertical components of reaction at A
Express your answers in terms of some or all of the variables W, R. Φ and θ). Enter your answers separated by a comma.
View Available Hint's)
Aa + Ay = ____
Parts B
Determine the one cable car necessary to hold the beans position shown
Express your answers in terms of some or all of the variables W, R. Φ and θ).
The reaction is in A in vertical direction is W(2cosϕsinθ−sinϕcosθ)/2sin(θ−ϕ).
What is Normal Stress and Strain?In terms of psychology, "stress" and "strain" are sometimes used interchangeably in popular culture, as in the expressions "I'm feeling stressed" or "I'm under a lot of pressure."
In engineering, these phrases have specific, technical meanings. If a hook in the steel wire is attached,
If you hang the wire from the ceiling while placing a weight on the lower end, it will sag. By dividing the length change by the starting length, the strain in the wire may be computed.
Thus, as per the given scenario, W(2cosϕsinθ−sinϕcosθ)/2sin(θ−ϕ) will be the equation.
For more details regarding stress and strain, visit:
https://brainly.com/question/13261407
#SPJ1
Kind of energy a piece of radioactive metal contains
Answer:
Radioactive materials give off a form of energy called ionizing radiation.
A box is pushed with a 245 N of force on a horizontal surface as it moves with a
constant velocity. The mass of the box is 104 kg. The box experiences a force of friction
of 45 N.
a. Draw a free body diagram with Fg, FN, F₂ and F₁.
b. Find the weight of the box.
c. Find the coefficient of friction as the box is moving.
d. Find the net force acting the box.
Answer:
Explanation:
b) Fg = W = mg = (104 kg)(9.8 m/s²) = 1019.2 N (weight of the box)
Ff = (coeff. friction)(N)
N = normal force = Fg = 1019.2 N
c) coeff. friction = Ff/N = 45 N/1019.2 N = 0.044
d) Fnet = 245 N - 45 N = 200 N
It's hard to draw a free body diagram with the available symbols, but here's a try at it. Just add a box between the arrows!
W
↓
Ff → ← Fapplied
↑
N
what is the atmosphere pressure on earth will support a column of mercury about 760 mm high, since the atmosphere pressure on the surface of the planet venus is 9200 kpa (1330 pal) , about 91 times that of earth about how tall a mercury column could venus’s atmosphere support ?
The atmospheric pressure on earth is 1 atm. This pressure is equivalent to the mercuric pressure of 760 mmHg. The atmospheric pressure on the surface of Venus is 9200 kpa which is equivalent to 69017 mmHg.
What is atmospheric pressure?Pressure is the force acting per unit area. In the atmosphere, the gaseous particles and dust exerts a pressure in the atmosphere. The atmospheric pressure depends on the temperature.
There are various units for pressure. Normally the atmospheric pressure is expressed in atm unit. The mmHg pressure is based on the raise in mercuric level with respect to increase in pressure.
1 mmHg = 0.0013133 atm
hence, 760 mmHg = 1 atm
On the surface of Venus, the pressure is 9200 kilopascal.
1 mmHg = 0.133 KPa
then 9200 KPa = 9200/0.133 = 69017 mmHg pressure.
Therefore, height of mercuric column will be 69017 mm in Venus surface.
Find more on atmospheric pressure:
https://brainly.com/question/1393320
#SPJ1
need help with Kirchhoff's rules
The nodal voltage is V and the currents are as defined in the diagram.
At the upper node, Kirchhoff's current law equation is I1+I5=I2+I3
What is Kirchhoff's rules?The voltage around a loop equals the sum of every voltage drop in the same loop for any closed network and equals zero. Put differently, the algebraic sum of every voltage in the loop has to be equal to zero and this property of Kirchhoff's law is called conservation of energy.Kirchhoff's circuit laws are two equalities that deal with the current and potential difference in the lumped element model of electrical circuits. They were first described in 1845 by German physicist Gustav Kirchhoff. This generalized the work of Georg Ohm and preceded the work of James Clerk Maxwell.Kirchhoff's first rule—the junction rule. The sum of all currents entering a junction must equal the sum of all currents leaving the junction. Kirchhoff's second rule—the loop rule. The algebraic sum of changes in potential around any closed circuit path (loop) must be zeroTo learn more about Kirchhoff's rules refers to:
brainly.com/question/13201349
#SPJ1
Three point charges are arranged at the corners of a square of side L as shown in Fig. What is the potential at the fourth corner (point A), taking V=0 at a great distance?
Thus the electric field at the fourth corner of the square of side L is E4 = kQ.[2/a² + 1/a√2].
What is Electric field strength?Electric field strength is a quantitative expression of the intensity of an electric field in an electric circuit at a particular location and time. The standard unit of the electric field strength is the volt per meter (V/m or V·m⁻¹). An electric field strength of 1 V/m represents a potential difference of about 1V between the two points which are separated by 1 meter distance.
We are given that:
Number of point charges = 3
Here, we shall use the superposition principle to calculate the net electric field at the fourth point, so
E4 = E1 + E2 + E3
E4 = kQ/a² + kQ/√(2a²) + kQ/a²
E4 = kQ [1/a² + 1/√(2a²) + 1/a²]
E4 = kQ [2/a² + 1/a√2]Thus the electric field at the fourth corner is E4 = kQ [2/a² + 1/a√2].
Learn more about Charge here:
https://brainly.com/question/3412043
#SPJ1
It is a “new moon” (the Moon is totally dark in the sky). Using the masses of the Earth, Sun, and Moon and the average distances between the Earth-Moon and Earth-Sun, find the net gravitational force on the Earth from the Sun and the Moon combined.
Find also distance when it is full moon
It is a “new moon” (the Moon is totally dark in the sky). The gravitational force between the Earth and the Moon is:
2.9 x 10^20 N3.5 x 10^22 N3.5 x 10^22 NWhat is gravitational force?Generally, The gravitational force between two objects is given by the equation:
force = G * (mass1 * mass2) / distance^2
Where G is the gravitational constant (6.67 x 10^-11 N*(m/kg)^2), mass1 and mass2 are the masses of the two objects, and distance is the distance between the two objects.
The mass of the Earth is 5.972 x 10^24 kg, the mass of the Moon is 7.347 x 10^22 kg, and the mass of the Sun is 1.989 x 10^30 kg. The average distance between the Earth and the Moon is 384,400 km, and the average distance between the Earth and the Sun is 149.6 million km.
The gravitational force between the Earth and the Moon is:
force = (G * (mass of Earth) * (mass of Moon)) / (distance between Earth and Moon)^2 force
= (6.67 x 10^-11 N*(m/kg)^2) * (5.972 x 10^24 kg) * (7.347 x 10^22 kg) / (384400 x 10^3 m)^2 force
= 2.9 x 10^20 N
The gravitational force between the Earth and the Sun is:
force = (G * (mass of Earth) * (mass of Sun)) / (distance between Earth and Sun)^2 force
= (6.67 x 10^-11 N*(m/kg)^2) * (5.972 x 10^24 kg) * (1.989 x 10^30 kg) / (149.6 x 10^9 m)^2 force
= 3.5 x 10^22 N
To find the net gravitational force on the Earth from the Sun and Moon combined, we add the two forces we found above.
Net force = 2.9 x 10^20 N + 3.5 x 10^22 N
= 3.5 x 10^22 N
When it is a Full Moon the distance is the same 384,400 km
Read more about gravitational force
https://brainly.com/question/12528243
#SPJ1
Find the location of the CM of a system of three particles arranged such that two of the particles with mass m are separated by distance I along the y-axis. The third mass 2m lies on the x-axis and is separated by a distance I from one of the masses.
Answer:
CM of a system ( 0.5l , 0.25l )
Explanation:
x = (m1.x1 +m2.x2 +m3.x3) / ( m1 + m2 +m3)
x = ( m x 0 + m x 0 + 2m x l ) / ( m+m+2m)
x = 2m x l / 4m
x = 0.5 l
y = (m1 x y1 +m2 x y2 +m3 x y3) / ( m1 + m2 +m3)
y = (m x 0) + m x l + 2m x 0 ) / ( m + m + 2m )
y = m x l / 4m
y = 0.25 l
Calculate the potential energy of a rock of mass 500 g, held at a height of 2 m above ground.
The potential energy of a rock of mass 500 g, held at a height of 2 m above ground is 9.8J.
The formula for the gravitational potential energy of an object is:
PE = mgh
where m is the mass of the object, g is the acceleration due to gravity (approximately 9.8 m/s^2 on the Earth's surface), and h is the height of the object above the reference point.
So, in this case, we can plug in the given values to find the potential energy of the rock:
PE = (500 g) x (9.8 m/s^2) x (2 m)
The weight of the rock is m*g = 500 g * 9.8 m/s^2 = 4.9 N
Therefore,
PE = 4.9 N x 2 m = 9.8 J
Therefore, the potential energy of a rock of mass 500 g, held at a height of 2 m above ground is 9.8J.
Learn more about Energy:
https://brainly.com/question/29979940
Write two or three sentences to describe the conductivity of a conductor. Explain its conductivity in terms of the electrons in it.
The conductivity of a conductor refers to its ability to conduct electrical current.
A material that has high conductivity allows electrical charges to flow through it easily and with little resistance, while a material with low conductivity does not allow electrical charges to flow as easily and has more resistance.
The conductivity of a conductor is determined by the number of free electrons in the material, as well as how easily these electrons can move through the material.
In a conductor, the atoms are closely packed together and the electrons are not tightly bound to the atoms, allowing them to move freely through the material and carry an electrical charge. This facilitates the flow of electrical current through the material, resulting in high conductivity.
Learn more about conductors:
https://brainly.com/question/18084972
How long would you have to film something in HD to collect 1 PB of data?
all day for 2 consecutive weeks
all day for 365 days (or 364 days in a leap year)
all day for about 3.5 years
all day for one light year
Time required to film something in HD to collect 1 PB of data is all day for about 3.5 years.
What is Petabyte?A petabyte, or 2 to the 50th power of a byte, is a unit of measurement for memory or data storage. One exabyte is equal to about 1,024 petabytes (PB), or 1,024 terabytes (TB).
Although traditional network-attached storage (NAS) can handle petabytes of data and is expandable, it might be resource-intensive to traverse the system's ordered storage index.
A common laptop or desktop computer has 16 GB of random access memory for storage (RAM).
Learn more about Petabytes here:
https://brainly.com/question/29060237
#SPJ1
What are the magnitude and direction of the current in the 20 Ω resistor in (Figure 1)?
Express your answer with the appropriate units. Enter positive value if the current is clockwise and negative value if the current is counterclockwise.
To solve this we must be knowing each and every concept related to net current. Therefore, the circuit's overall net current is 0.1 A, flowing clockwise.
What is the net current?The term "net current" refers to the total currents after taking current direction into account. If a node sends 1 mA inside and 5 mA out, the total current equals 4 mA out.
The sum of all entering currents must match the sum of all exiting currents, according to KCL. According to Ohm's Law, the current flowing is equivalent to the combined voltage dividing by the entire resistance. In contrast to a series circuit, where the total current is the same across all of the components, the total current inside a parallel connection is really only equal to the particular current in that part of the circuit.
Net current
i = V / Ri
= (9 - 6) / (10 + 20)i
= 0.1 A
in clockwise way
Therefore, the circuit's overall net current is 0.1 A, flowing clockwise.
To know more about net current, here:
brainly.com/question/28326769
#SPJ1
Find the full load primary and secondary current of a 230/115V, 2kVA transformer.
The full load primary current of a 230/115V, 2kVA transformer can be calculated using the formula:
I_primary = (2kVA * 1000 VA/kVA) / (230V)
I_primary = 8.7V
The full load secondary current of the transformer can be calculated using the formula:
I_secondary = (2kVA * 1000 VA/kVA) / (115V)
I_secondary = 17.4V
Therefore, the full-load primary current of the transformer is approximately 8.7V, and the full-load secondary current is approximately 17.4V. It is important to note that these values are based on the assumption that the transformer is operating at its full load capacity. If the transformer is operating at a lower load, the primary and secondary currents will be correspondingly lower.
5.33 A constant force F= (4.70-379, 2.09) N. acts on an object of mass 180 kg, causing a displacement of that object by F= (4.25, 3.69-245) m What is the total work done by this force
The total work done by this force is 28.9-1457.86 N m.
What is total work?Total work is the sum of all the energy expended in completing a job or task. It is the amount of effort and energy expended to accomplish a goal or complete a task. Total work can be calculated by adding up all of the individual components of the job or task, such as time, effort, and materials.
The total work done by this force can be calculated using the formula W = F * Δx, where F is the force vector, and Δx is the displacement vector. In this case, the total work done is:
W = (4.70-379, 2.09) * (4.25, 3.69-245) = (19.9-944.81, 8.00-513.05) N m
Therefore, the total work done is 28.9-1457.86 N m.
To learn more about total work
https://brainly.com/question/25573309
#SPJ1
I would like to ask for help in understanding on what basis the universe is considered to be expanding? As far as I understand, it is only an idea (hypothesis, theory) and not a scientific fact as the media presents it. Given that we on Earth receive evidence of various radiations from the past, we cannot say with certainty that the Universe is still expanding. Let's say the Universe stopped expanding 4 billion years ago and started contracting, would the results of all our observations be the same as they are or not?
Expansion of universe is not a hypothetical one but the universe is expanding in the sense increase distance over the space and dark matter.
What is universal expansion?The increase in distance over time between any two particular gravitationally unbound regions of the observable universe is known as the universe's expansion.
As a result, the size of space itself expands intrinsically. It is not necessary for space to exist outside of the cosmos or for it to extend into anything.
The metric changes in scale rather than space or the things in space moving in the conventional sense. Objects move farther apart from one another at ever-increasing speeds as the spatial component of the universe's spacetime metric scales up.
Any viewer in the cosmos would see that all of space appears to be expanding, except for the galaxies receding with a speed proportional to the distance from the observer.
Find more on universal expansion:
https://brainly.com/question/16048709
#SPJ1
A thin rod has a length of 0.609m and rotates in a circle on a frictionless tabletop. The axis is perpendicular to the length of the rod at one of its ends. The rod has an angular velocity of 0.606rad/s and a moment of inertia of 1.05 x 10^-3 kg•m^2. A bug standing on the axis decides to crawl out to the other end of the rod. When the bug (whose mass is 5 x 10^-3 kg) gets where it’s going, what is the change in the angular velocity of the rod?
Answer:
-0.0069 rad/s
Explanation:
The change in angular velocity of the rod can be determined by using the conservation of angular momentum equation: Lf = Li.
The initial angular momentum of the rod is Li = Iwo and the final angular momentum of the rod is Lf = Iwf.
Plugging in the given values, we get:
(1.05 x 10^-3 kg•m^2)(0.606 rad/s) + (5 x 10^-3 kg)(0.609 m)^2(wf) = (1.05 x 10^-3 kg•m^2)(wo).
Solving for wf, we get wf = -0.0069 rad/s.
Therefore, the change in angular velocity of the rod is -0.0069 rad/s.
If a vehicle goes from 15.0 km/h to 28.0 km/h in 4.60 seconds, how far will it have traveled?
Answer:
To find the distance the vehicle traveled, you will need to find the average speed of the vehicle over the 4.60 seconds and multiply that by the time traveled.
The average speed of the vehicle can be found by adding the initial speed and the final speed, and then dividing by 2: (15.0 + 28.0) / 2 = 21.5 km/h.
The distance traveled can be found by multiplying the average speed by the time traveled: 21.5 km/h * 4.60 s = 98.7 km.
So, the vehicle will have traveled 98.7 km.
Explanation:
Those in mission control roles spend about 75 percent of their time actively communicating and controlling active space missions.
True
False
It is False that personnel in mission control spend roughly 75% of their time actively engaging with and managing running space missions, according to the evidence at hand.
What is Mission control centre?The NASA Johnson Space Center has a designated center called Mission Control Center.
Only 10% of the time that the MCC staff devotes to mission control is actually spent actually managing missions; the other 80% is spent planning and organizing, and the remaining 15% is spent on training and education.
A facility that oversees space flights is known as a mission control center (MCC; sometimes known as a flight control center or operations center), often from the point of launch until landing or the mission's conclusion. It is a component of spacecraft operations on the ground.
Therefore, It is False that personnel in mission control spend roughly 75% of their time actively engaging with and managing running space missions, according to the evidence at hand.
To learn more about Mission control, refer to the link:
https://brainly.com/question/25963453
#SPJ1
Equilibrium exists in a system where three forces are acting concurrently on an object. If the system includes a 5.0-newton force due north and a 2.0-newton force due south, the third force must be?
The third force must be 3.0 newtons due north in order for equilibrium to exist in the system.
Why should equilibrium exist in system?This is so because the total of all the forces acting on the object equals the net force acting on it. The net force in this situation is 3.0 newtons due north and is calculated by subtracting the 5.0 newton force due north from the 2.0 newton force due south.In equilibrium, the net force on an object is zero.A chemical reaction is said to be in a state of north equilibrium when the reactant and product concentrations remain stable throughout time. The concentrations of the reactants and products stay unchanged, and the rate of the forward reaction is equal to the rate of the reverse reaction.To know more about equilibrium, check out :
https://brainly.com/question/18849238
#SPJ1
Hi can anyone please help me with this question? i just cant seem to do it.. Thanksss
Newtons Universal Gravitational Law.
Bill gates a billionaire and space-X CEO, send Robin, 65kg, to planet Gidz. Gidz has a very weak gravitational attraction, of 1.56 N/Kg. Planet GIdz has a radius of 6.35 x 10^11 m.
i. determine the mass of planet Gidz.
Answer:
F = G M m / R^2 = m a
G M / R^2 = a
M = a R^2 / G
M = 1.56 N/kg * 6.35 m^2 / 6.67E10-11 N-m^2 / kg^2
M = 1.56 * 6.35 / 6.67E-11 kg
M = 1.49 * 10^11 kg
Part A
What is the radius of the hydrogen-atom Bohr orbit shown in the figure? (Figure 1)
r = ____ nm
The radius of the hydrogen-atom Bohr orbit shown in the figure is 5.3 nm.
What is Bohr orbit?The path that hypothetical electrons take around the nucleus is known as Bohr's orbit.
These orbits are described by Bohr in his hypothesis of the structure of an atom as energy levels or shells where electrons move in a fixed circle around the nucleus.
These orbits resemble solar system orbits, with the exception that they are attracted by electrical forces rather than gravity. The term "ground state" refers to the amount of energy that an electron typically occupies.
Learn more about Bohr orbit here:
https://brainly.com/question/17308813
#SPJ1
A 6 kg bowling ball is lifted 1.2 m into a storage rack. The acceleration of gravity is 9.8 m/s² Calculate the increase in the ball's potential energy. Answer in units of J.
Answer:
70.56 J
Explanation:
Gravitational Potential Energy= mass×gravitational pull× height
= 6×9.8×1.2= 70.56 J
1- A ball, M = 4 kg is released from rest (vi =0) at a height, h = 2 m above the ground. (a)
What is the kinetic energy of the ball just before it hits the ground? What is the change in the
potential energy, ΔU during this motion? (b) Find the kinetic energy of the ball at a height, y
= 1.2 m above the ground. (Take g = 10 m/s2
).
(a) The kinetic energy of the ball just before it hits the ground is 78.4 J.
(b) The kinetic energy of the ball at a height of 1.2 m is 31.36 J.
What is the kinetic energy of the ball?The kinetic energy of the ball just before it hits the ground is calculated as follows;
K.E ( bottom) = P.E (top)
P.E (top) = mgh
where;
m is the mass of the objecth is the height of the objectg is acceleration due to gravityP.E (top) = 4 x 9.8 x 2
P.E (top) = 78.4 J
The change in the potential energy of the ball during its motion is calculated as follows;
ΔU = P.Ef - P.E i
where;
P.Ef is the final potential energy at ground levelP.Ei is the initial potential energy at maximum heightΔU = 0 J - 78.4 J
ΔU = -78.4 J
The kinetic energy of the ball at a height of 1.2 m is the change in the potential energy of the ball and it is calculated as follows;
K.E = -ΔU
K.E = -mg (hf - hi)
K.E = (4 x 9.8)(2m - 1.2 m)
K.E = 31.36 J
Learn more about kinetic energy here: https://brainly.com/question/25959744
#SPJ1
• Calculate the magnetic field strength inside a solenoid with a radius of 2m and has 2000 loops. Furthermore, it carries a 1600 A current?
The magnetic field strength of the solenoid of radius 2 m is 2.0096 T.
What is a magnetic field?Magnetic field is the region or space around which magnetic force is felt or experienced.
To calculate the magnetic field strength inside a solenoid, we use the formula below.
Formula:
B = μni/r......................... Equation 1Where:
μ = permeability of free spacen = Number of loopsr = Radius of the solenoidB = Magnetic field strengthi = CurrentFrom the question,
Given:
μ = 4π×10⁻⁷T.m/Ai = 1600 An = 2000 loopsr = 2 mSubstitute these values into equation 1
B = (4π×10⁻⁷×1600×2000/2)B = 2.0096 THence, the magnetic field strength is 2.0096 T.
Learn more about magnetic field here: https://brainly.com/question/26257705
#SPJ1
A 6 kg bowling ball is lifted 1.2 m into a storage rack. The acceleration of gravity is 9.8 m/s². Calculate the increase in the ball's potential energy. Answer in units of J.
Answer:
70.56 J
Explanation:
The increase in potential energy of the ball can be calculated using the formula:
PE = mgh
where:
PE is the increase in potential energy
m is the mass of the ball (6 kg)
g is the acceleration of gravity (9.8 m/s²)
h is the height the ball is lifted (1.2 m)
Substituting in the values, we get:
PE = (6 kg)(9.8 m/s²)(1.2 m)
This simplifies to:
PE = 70.56 J
So the increase in the ball's potential energy is 70.56 J.
What is the meaning of the density of states function?
Ans-The density of states function describes the number of states that are available in a system and is essential for determining the carrier concentrations and energy distributions of carriers within a semiconductor.
Answer:
density equal to mass upon volume
simple definition
Compared to using analog signals, what is an advantage of transmitting
information using digital signals?
A. Digital signals become stronger as the distance from their source
increases.
B. Digital signals are more secure.
C. Digital signals have a continuous range of values.
D. Digital signals can use the cloud to store and access data.
Answer:
B. Digital signals are more secure
Explanation:
You want to know an advantage of transmitting information using digital signals.
Digital signalsDigital signals are characterized by having a few discrete states. In the simplest case, those states are {transmitting, not transmitting}. Modern digital signals are often transmitted using numerous combinations of phases, frequencies, and amplitudes.
Analog signalsAnalog signals are characterized by a continuum of the characteristic used to convey the information. When amplitude modulation is used, the information of interest is conveyed by the amplitude of the signal. Similarly, when frequency or phase modulation is used, the information is conveyed by the frequency or phase of the signal, respectively.
That is, analog signals have a continuous range of values.
DistanceAny signal that is broadcast will have a signal level that decreases with distance from the source of the broadcast. Any signal conveyed through a medium will be subjected to distortions and losses due to the interaction of the signal and the medium. Hence all signals become weaker as the distance from the source increases.
NoiseThe receiver of a signal will, in general, receive signals other than the one intended. These are referred to as "noise." A transmission channel may have many sources of noise, including other transmitters, Cosmic Background Radiation, thermal noise in the components of the receiver or transmission medium, and others.
For analog signals, noise can directly affect the amplitude or phase being used to represent the signal of interest. Hence it changes the received value so it is not the same as the transmitted value.
The states of digital signals are designed to be sufficiently far apart that any corruption by noise will not affect the value as interpreted by the receiver. Thus, in terms of corruption of the information, we can say digital signals are more secure.
__
Additional comment
In radio transmission, noise is generally an addition to the signal. The weaker the analog signal, the greater the effect of noise. Broadcast radio began as AM radio: amplitude modulated. As the signal weakens, noise becomes a greater portion of the amplitude, so the receiver hears "static" where they want to hear voice or music.
FM, frequency modulated, radio replaced AM radio in order to avoid this issue with noise. The frequency of a signal is less likely to be corrupted. However, as the signal weakens, it can be difficult to determine its frequency, so that method of analog transmission also succumbs to noise.
Digital transmission in a noisy channel can also be corrupted by noise. Ultimately, the rate of information transmission in a given channel depends on the channel bandwidth and the signal-to-noise ratio. The integrity of a signal can be improved through coding that allows missing or corrupted bits of information to be determined based on the other bits that are received.
"Security" of a transmission can have different meanings. Here, we understand it to refer to the integrity of the information being conveyed. It could also relate to the difficulty of intercepting the transmission, or the difficulty of understanding the meaning of the received signal. Digital signals may or may not be more "secure" in these other meanings of the word.