A pair of vertical, open-ended glass tubes inserted into a horizontal pipe are often used together to measure flow velocity in the pipe, a configuration called a Venturi meter. Consider such an arrangement with a horizontal pipe carrying fluid of density ρ . The fluid rises to heights h1 and h2 in the two open-ended tubes (see figure). The cross-sectional area of the pipe is A1 at the position of tube 1, and A2 at the position of tube 2.
a) Find p1, the gauge pressure at the bottom of tube 1. (Gauge pressure is the pressure in excess of outside atmospheric pressure.) Express your answer in terms of quantities given in the problem introduction and g, the magnitude of the acceleration due to gravity.
b) Find v1, the speed of the fluid in the left end of the main pipe. Express your answer in terms of h1, h2, g, and either A1 and A2 or γ, which is equal to A1A2.

The angle of refraction (Theta) at the second face of the sapphire prism is approximately 63 degrees .(D)

To find the angle of refraction at the second face, follow these steps:

1. Use Snell's Law to find the angle of refraction (r1) at the first face: (D)
n1 * sin(i) = n2 * sin(r1)

2. Calculate the angle inside the prism (α):
α = 180 - angle of the prism - r1

3. Use the total internal reflection condition for the second face to find the critical angle (θc):
sin(θc) = n2 / n1

4. Use the angle of incidence (i) at the second face:
i2 = α + θc

5. Use Snell's Law again to find the angle of refraction (Theta) at the second face:
n2 * sin(i2) = n1 * sin(Theta)  

To know more about Snell's Law click on below link:

https://brainly.com/question/2273464#

#SPJ11

The length of the pendulum on the moon would need to be approximately 0.276 meters (to three significant digits) to have a period of 1.7 seconds.

The period (T) of a pendulum is given by the equation:
T = 2π√(L/g)
g(moon) = 1/6 g(earth)
Substituting this into the equation for T, we get:
T = 2π√(L/g(moon))
T = 2π√(L/(1/6 g(earth)))
T = 2π√(6L/g(earth))
1.7 s = 2π√(6L/9.81 m/s^2)
2.89 s^2 = 24π^2 L/9.81 m/s^2
L = (2.89 s^2 × 9.81 m/s^2)/(24π^2)
L ≈ 0.223 m

Therefore, the pendulum would have to be approximately 0.223 meters long in order to have a period of 1.7 s on the moon. To find the length of a pendulum on the moon with a period of 1.7 seconds, we'll use the formula for the period of a simple pendulum: T = 2π√(L/g), where T is the period, L is the length, and g is the acceleration due to gravity.

To know more about pendulum visit :-

https://brainly.com/question/14759840

#SPJ11

According to the question the maximum distance the frame moves downward is 0.412 m.

Distance is a measure of the space between two objects or points. It is a scalar quantity, meaning it is only described by magnitude and not by direction.

Using the equation [tex]E_i[/tex] = [tex]E_f[/tex], we can solve for the maximum displacement x of the frame, which is equal to the maximum distance the frame moves downward.
[tex]E_i[/tex]   = mgh = 0.200 kg * 9.8 m/s² * 0.300 m = 5.88 J
[tex]E_f[/tex] = 1/2mv² + 1/2kx²
Substituting in the given values, we get
5.88 J = 1/2(0.200 kg)v² + 1/2(0.290 kg)(0.0400 mm)²
Solving for v, we get
v = 2.93 m/s
Assuming that the putty stops moving when it reaches the frame, the maximum displacement of the frame is equal to the distance traveled by the putty. Thus, the maximum displacement of the frame is
d = vt = 2.93 m/s * (2*0.300 m/2.93 m/s) = 0.412 m
Therefore, the maximum distance the frame moves downward is 0.412 m.

To learn more about distance
https://brainly.com/question/26550516
#SPJ1

The right ventricle of the heart pumps oxygen-poor blood to the lungs. The correct answer is B.

This is because the right atrium receives oxygen-poor blood from the body and then passes it on to the right ventricle, which then pumps it to the lungs for oxygenation. Once the blood is oxygenated, it returns to the left side of the heart via the pulmonary vein, and the left ventricle then pumps the oxygen-rich blood to the body. The right ventricle of the heart pumps oxygen-poor blood to the lungs. In this process, the right ventricle receives oxygen-poor blood from the right atrium and pumps it into the pulmonary artery, which then transports the blood to the lungs to get oxygenated.

To know more about Ventricles visit:

https://brainly.com/question/29564818

#SPJ11

The speed of the longitudinal pulse will be different from the speed of the transverse pulse.The speed of longitudinal pulses is determined by the bulk modulus of the spring, which is different from the properties that determine the speed of transverse pulses.

Since the speed of a pulse on a spring is determined by the properties of the spring and not by the amplitude or frequency of the pulse, the time it takes for the reflected pulse to return to the generating student will be the same as the time it took for the original pulse to travel from one end of the spring to the other.

Therefore, it will take another 0.60 seconds for the reflected pulse to return to the generating student.

When a second pulse of twice the original amplitude is sent, the pulse will take the same time to reach the far end of the spring.

This is because the speed of the pulse is determined by the properties of the spring and not by the amplitude of the pulse.

When the students move farther apart, the spring becomes more stretched. The speed of a pulse on a spring is inversely proportional to the square root of the mass per unit length of the spring.

When the spring is more stretched, the mass per unit length increases, which causes the speed of the pulse to decrease.

Therefore, the speed of the pulse on the more stretched spring will be slower than the speed of the pulse when they were 5.0 m apart.

]When the students move back to their original separation of 5.0 m and the generator produces a longitudinal pulse, the speed of this pulse will be different from the speed of the transverse pulse.

Longitudinal pulses travel through the compression and rarefaction of the spring, whereas transverse pulses travel through the oscillation of the spring.

The speed of longitudinal pulses is determined by the bulk modulus of the spring, which is different from the properties that determine the speed of transverse pulses.

Therefore, the speed of the longitudinal pulse will be different from the speed of the transverse pulse.

Learn more about transverse pulse.

brainly.com/question/20039194

#SPJ11

(a) The angular speed of the wheel sprocket is 8.47 rad/s. (b) The linear speed of the bicycle is 5.5 m/s. (c) To travel at a speed of 3.5 m/s, it takes the pedal 1.17 seconds to make one complete revolution.

(a) To find the precise speed of the wheel sprocket, we can utilize the proportion of the radii.

ωw = (rp/rw) * ωp = (9.5 cm/4.5 cm) * (2π rad/1 fire up) * (1 fire up/1.7 s) = 8.47 rad/s.

(b) The direct speed of the bike is given by v = R * ωw, where R is the sweep of the bike wheel.

v = 65 cm * 8.47 rad/s = 5.5 m/s.

(c) To make the opportunity it takes for the pedal to make one complete transformation at a speed of 3.5 m/s, we can utilize the equation v = R * ωp, where v = 3.5 m/s and R = 65 cm.

ωp = v/R = 3.5 m/s/0.65 m = 5.38 rad/s.

The ideal opportunity for one unrest is T = 2π/ωp = 2π/5.38 rad/s = 1.17 s/fire up.

To learn more about speed and radius, refer:

https://brainly.com/question/30557816

#SPJ4

Near this particular time, the electric field of the evector of sinusoidal electromagnetic waves is 300 V/m at its highest value.

(i) On a current element's direction, the electromagnetic field is at its lowest point, or zero. (ii) The current element's magnetism is strongest in a plane that passes through it and is parallel to its axis.

The highest and lowest magnetic field conditions If the angle among the magnetization line on the surface is 0, the flux of magnetic energy obtained is at its maximum. When the angle among the magnetization line and the outermost layer is ninety degrees, the flux of magnetic energy produced is at its lowest.

To know more about waves visit:

https://brainly.com/question/25954805

#SPJ1

The magnitude impulse needed to change the momentum of the 2.0 kilogramme item by +50 kg m/s is +50 Ns.

To find the magnitude impulse that will give a 2.0 kg object a momentum change of magnitude +50 kgm/s, we can use the impulse-momentum theorem.
1. Understand the impulse-momentum theorem: The impulse-momentum theorem states that the impulse (I) applied to an object is equal to the change in momentum (Δp) of the object, or I = Δp.

2. Identify the given values: In this problem, you're given the mass (m) of the object as 2.0 kg and the change in momentum (Δp) as +50 kgm/s.

3. Use the impulse-momentum theorem to find the impulse: Since we know that I = Δp, we can plug in the given value of Δp to find the impulse (I):

I = +50 kgm/s

4. Verify that the answer is in the correct units: The units of impulse are Newton-seconds (Ns), and since our calculated impulse is +50 kgm/s, we can confirm that it is equivalent to +50 Ns, as 1 Ns is equal to 1 kgm/s.

So, the magnitude impulse that will give a 2.0 kg object a momentum change of magnitude +50 kgm/s is +50 Ns.

For more such questions on magnitude , click on:

https://brainly.com/question/30337362

#SPJ11

The vector sum of the forces imposed by the other two particles is the net force acting on particle [tex]q_1[/tex]. By applying Coulomb's law, we may determine the size of the force [tex]q_2[/tex] has on  [tex]q_1[/tex]:

A method called an experiment is used to test a hypothesis or educated estimate in order to confirm or deny it. In order to investigate novel occurrences or to confirm and validate accepted theories or principles, experiments are carried out.

[tex]F_{12} = (k*q1*q2)/(0.10m)^2\\\\F_{12}=(8.99*10^9 N*m^2/C^2)*(8*10^{-6} C)*(3.5*10^{-6} C)/(0.10m)^2\\\\F_{12}=2.8*10^{-4} N[/tex]

In a similar manner, we can determine the strength of the force that [tex]q_3[/tex] has on [tex]q_1[/tex]:

The vector sum of the two forces equals the net force acting on [tex]q_1[/tex]. The force due to  [tex]q_2[/tex]  is directed to the right whereas the force due to [tex]q_3[/tex]  is pointing to the left because  [tex]q_2[/tex]  has a positive charge and [tex]q_3[/tex]  has a charge that is negatively charged. Consequently, the net force on [tex]q_1[/tex] is equal to and is to the right.

[tex]F_{net}=F_{12 }+ F_{13}\\\\F_{net}=2.8*10^{-4 N} + (-1.9*10^{-4 N})\\\\F_{net}=0.9*10^{-4} N.[/tex]

To learn more about particles, visit:

brainly.com/question/27911483

#SPJ1

To solve for the separation of the two slits in Young's experiment, we can use the equation:

d * sinθ = mλ

where d is the separation of the slits, θ is the angle of diffraction, m is the order of the fringe, and λ is the wavelength of the light.

First, we need to find the angle of diffraction for the twentieth fringe. Using the small angle approximation, we can assume that:

sinθ ≈ tanθ = y/L

where y is the distance from the central bright fringe to the twentieth fringe, and L is the distance from the slits to the screen.

Plugging in the given values, we have:

sinθ ≈ tanθ = y/L = 10.6 mm / 1.20 m ≈ 0.0088

Next, we can solve for the separation of the slits by rearranging the equation:

d = mλ / sinθ

Since we are measuring the twentieth fringe, m = 20. Plugging in the values, we get:

d = 20 * 502 nm / 0.0088 ≈ 1.14 × 10^-4 m

Therefore, the separation of the two slits is approximately 1.14 × 10^-4 meters.
Using the information provided, we can find the separation of the two slits in Young's experiment by applying the formula for fringe spacing in a double-slit interference pattern:

Δy = (m * λ * L) / d

where Δy is the fringe spacing, m is the fringe order, λ is the wavelength, L is the distance from the double slit to the screen, and d is the slit separation.

Given:
λ = 502 nm = 502 x 10^-9 m
L = 1.20 m
Δy = 10.6 mm = 10.6 x 10^-3 m
m = 20 (20th fringe)

Now, rearrange the formula to solve for d:

d = (m * λ * L) / Δy

Plug in the given values:

d = (20 * 502 x 10^-9 * 1.20) / (10.6 x 10^-3)

Calculate the result:

d ≈ 2.27 x 10^-6 m

The separation of the two slits is approximately 2.27 x 10^-6 meters, or 2.27 μm.

Visit here to learn more about fringe spacing brainly.com/question/17212031

#SPJ11

The largest angle of incidence, θa , for which total internal reflection will occur at vertical face is any angle greater than 51.06°.

To find the largest angle of incidence (θa) for total internal reflection at the vertical face, you need to use the critical angle formula:

Critical Angle (θc) = arcsin(1/n)

Where n is the refractive index.

In this case, n = 1.28. Plug the value into the formula:

θc = arcsin(1/1.28)

θc ≈ 51.06°

For total internal reflection to occur, the angle of incidence (θa) must be greater than the critical angle. Therefore, the largest angle of incidence for which total internal reflection will occur at the vertical face is any angle greater than 51.06°.

Learn more about angle of incidence here: https://brainly.com/question/30402542

#SPJ11

A charged particle with a magnitude of -1.24×10⁻⁸C is in motion with a velocity of (4.19×10⁴m/s)i^ + (-3.85×10⁴m/s)j^. The force exerted on the particle by the magnetic field is -2.3484×10⁻³ N in the z-direction, while the x and y components of the force are zero.

To calculate the force exerted on the particle by the magnetic field, we can use the formula for the magnetic force on a moving charged particle:

F⃗ = q (v⃗ × B⃗)

where q is the charge of the particle, v⃗ is its velocity, and B⃗ is the magnetic field.

Given:

q = -1.24×10⁻⁸ C (charge of the particle)

v⃗ = (4.19×10⁴ m/s)i^ + (-3.85×10⁴ m/s)j^ (velocity of the particle)

B⃗ = (1.90 T)k^ (magnetic field)

Calculating the force:

F⃗ = q (v⃗ × B⃗)

= (-1.24×10⁻⁸ C) [(4.19×10⁴ m/s)i^ + (-3.85×10⁴ m/s)j^] × (1.90 T)k^

The cross product of v⃗ and B⃗ can be calculated as follows:

i^ × k^ = j^ (unit vectors perpendicular to each other)

j^ × i^ = -k^ (unit vectors perpendicular to each other)

Therefore:

F⃗ = (-1.24×10⁻⁸ C) (-3.85×10⁴ m/s)(1.90 T)

= (2.3484×10⁻³ N)k^

The force exerted on the particle by the magnetic field has only a z-component, which is -2.3484×10⁻³ N. The x and y components are both zero.

So, the components of the force separated by commas are 0, 0, and -2.3484×10⁻³ N.

To know more about the force exerted refer here :

https://brainly.com/question/8737101#

#SPJ11

The circle's radius is 0.517 metres. The loop's new magnetic flux is 0.836 Wb.

(a) Given that the magnetic field has a magnitude of 0.300 T and the magnetic flux across the loop is 2.70 Wb, we have:

Φ = Bπ[tex]r^2[/tex]

[tex]2.70 Wb = 0.300 T \times \pi r^2[/tex]

[tex]r^2[/tex] = [tex]2.70 Wb / (0.300 T \times \pi)[/tex]

r = [tex]\sqrt{(2.70 Wb / (0.300 T \times \pi))[/tex] = 0.517 m

Therefore, the radius of the circular loop is 0.517 m.

(b) The new radius is if the loop radius is twice, then 2r = 1.034 m. The magnetic flux through the loop is given by the same formula Φ = Bπ[tex]r^2[/tex], but with the new radius. Therefore, we have:

Φ' = Bπ[tex](2r)^2[/tex]

Φ' = Bπ(4[tex]r^2[/tex])

Φ' = 4Bπ[tex]r^2[/tex]

The result of substituting the values of B and r is:

Φ' = 4(0.300 T)π[tex](0.517 m)^2[/tex]

Φ' = 0.836 Wb

The quantity of magnetic field travelling through a specific surface is measured by magnetic flux. It is denoted by the symbol and is defined as the sum of the surface area perpendicular to the magnetic field's area A and magnetic field intensity B. In mathematics, is equal to BAcos(), where is the angle formed by the magnetic field and the surface normal.

Due to its critical significance in the behaviour of magnetic materials and the interplay between magnetic fields and electric currents, magnetic flux is a key term in the study of electromagnetism. Additionally, it plays a crucial role in the construction and functioning of a variety of electrical appliances, like as transformers, motors, and generators.  

To learn more about Magnetic flux visit here:

brainly.com/question/31501008

#SPJ4

The car's shocks must remove 140.625 Joules of energy to dampen the oscillation.

To calculate the energy that the car's shocks must remove to dampen an oscillation starting with a maximum displacement of 0.0750 m and a force constant of 5.00×10^4 N/m, you can use the formula for potential energy in a spring system:

Potential Energy (PE) = (1/2) × Force Constant (k) × Displacement (x)^2

Here, the force constant (k) is 5.00×10^4 N/m and the maximum displacement (x) is 0.0750 m.

PE = (1/2) × (5.00×10^4 N/m) × (0.0750 m)^2

Now, perform the calculations:

PE = (1/2) × (5.00×10^4 N/m) × (0.005625 m^2)
PE = 0.5 × 5.00×10^4 N/m × 0.005625 m^2
PE = 140.625 J

To learn more about Force Constant, visit:

https://brainly.com/question/25313999

#SPJ11

Depending on the desired magnetic field configuration, the switch modifies the current in the coils to vary the magnetic field, making it either almost uniform or strongly gradient.

The magnetic flux across a loop can be altered in one of three ways: Alter the magnetic field's strength across the surface (raise, reduce). Adjust the loop's surface area.

The bar magnet's magnetic field is strongest at its centre and weakest between its two poles. The magnetic field lines are least dense between the two poles and most dense at the centre.

To know more about magnetic field visit:-

https://brainly.com/question/24397546

#SPJ1

The circumference of a circle is given by the formula C = πd, where C is the circumference and d is the diameter of the circle. Therefore, the circumference of each tire is:

C = πd = π(68 cm) ≈ 213.63 cm

To find the number of revolutions made by the wheels, we need to know the distance traveled by the bicycle in terms of the circumference of the wheels. We can use the formula:

distance = number of revolutions * circumference

Rearranging this formula, we get:

number of revolutions = distance / circumference

Substituting the given values, we get:

number of revolutions = 8.0 km / (2π × 0.68 km) ≈ 58.5 revolutions

Therefore, the wheels of the bicycle make approximately 58.5 revolutions.

Learn more about  diameter   here:

https://brainly.com/question/5501950

#SPJ11

The total impulse received by the body is approximately 42.43 Ns.

Impulse is a measure of the change in momentum of an object resulting from a force acting upon it for a period of time. It is defined as the product of the force and the time interval over which it acts, and is represented by the symbol "J".

To find the total impulse received by the body, we need to use vector addition to add the two impulses together. Since the impulses are at an angle of 55 degrees to each other, we can use the law of cosines to find the magnitude of the resultant impulse:

I² = 24² + 35² - 2(24)(35)cos(55)

I² = 576 + 1225 - 1680cos(55)

I² = 1801.9

I ≈ 42.43 Ns

To know more about impulse, here

brainly.com/question/30466819

#SPJ1

Answer:

S = V T       distance = speed * time

S1 = 20 * T1 = S/4               T1 = S / 80

S2 = 30 * T2 = 3 S / 4         T2 = S / 40

V = S / T = S / (T1 + T2)

T1 + T2 = S (1/40 + 1/80) = 120 S / 3200 = .0375 S

V = S / (.0375 S) = 26.7      average speed

The resistivity of the wire does not change when both its length and diameter are cut in half. The answer is (c) rho.

The resistance of a wire is given by the formula:

R = (ρ * L) / A

where R is resistance, ρ is resistivity, L is length, and A is the cross-sectional area of the wire.

For a cylindrical wire, the cross-sectional area is given by:

A = Π * (d/2)²

where d is the diameter of the wire.

If the length and diameter of the wire are both cut in half, then the new length and diameter are:

L' = L/2

d' = d/2

The new cross-sectional area is:

A' = Π * (d'/2)² = (Π/4) * d²

The new resistance is:

R' = (ρ * L') / A' = (ρ * L/2) / [(Π/4) * d²] = (2ρ * L) / (Π * d²)

We can write the new resistivity as ρ':

ρ' = R' * A' / L' = [(2ρ * L) / (Π * d²)] * [(Π/4) * d²] / (L/2) = ρ

The answer is (c) rho.

To know more about resistivity here:

https://brainly.com/question/29427458#

#SPJ11

The current through the primary winding if the radio operates at a current of 500 mA, the current through the primary winding is also 500 mA.

A transformer is a device that transfers electrical energy from one circuit to another through electromagnetic induction. It consists of two coils of wire, called the primary winding and the secondary winding, wrapped around a common magnetic core. When an alternating current (AC) flows through the primary winding, it creates a changing magnetic field that induces a voltage in the secondary winding. The voltage induced in the secondary winding depends on the ratio of the number of turns in the primary winding to the number of turns in the secondary winding. The current through the primary winding of a transformer depends on the voltage and impedance (resistance) of the circuit it is connected to. The current in the primary winding is not necessarily the same as the current in the secondary winding, since the voltage and impedance of the two circuits can be different.

The current through the primary winding is also 500 mA  is because the current in the primary winding directly supplies power to the radio, and therefore they share the same current value.

Learn more about primary winding: https://brainly.com/question/28865089

#SPJ11

The total charge inside a cylinder of length h and radius RCyl with charge density rho(R) = αR is given by qEnclosed = ∫(αR × 2πhRdR) from 0 to RCyl.

The electric field at points outside the cylinder (r > RCyl) is given by E = (1 / 4πε₀) × (qEnclosed / r²).

The direction of the electric field is radially outward when α > 0 (positive charge).


1. Integrate the charge density function to find the total charge: qEnclosed = ∫(αR × 2πhRdR) from 0 to RCyl.

2. Calculate the electric field at points outside the cylinder using Gauss's law: E = (1 / 4πε₀) × (qEnclosed / r²).

3. Determine the direction of the electric field. For α > 0 (positive charge), the electric field is radially outward.

To know more about Gauss's law click on below link:

https://brainly.com/question/2854215#

#SPJ11

If the primary current is less than two amperes for a transformer rated at 600 volts or less, the short-circuit protective device can be set at not more than 125% of this value.

What is Circuit?

A circuit is a closed path or loop through which electric current can flow. It consists of a source of electrical energy (such as a battery or power supply), conductive wires or cables, and one or more electrical components (such as resistors, capacitors, or switches) that are connected in a specific arrangement. The components in a circuit work together to control the flow of electric current and to perform a specific function, such as powering a device or controlling the brightness of a light bulb.

This is in accordance with the National Electrical Code (NEC) which states that for transformers with primary current of 9 amperes or less, the overcurrent protection may be set at 125% of the rated primary current if the transformer does not supply other transformers or loads. For transformers that supply other transformers or loads, the overcurrent protection should be set at the rated primary current of the transformer.

To know more about Circuit visit:

brainly.com/question/12608491

#SPJ1

The magnitude of the electric field at the dot is determined by the distance from the dot to the charge, the magnitude of the charge, and the electric constant (k).

To calculate the electric field at the dot, use the formula: E = k * |q| / r², where E is the electric field, k is the electric constant (8.99 x 10⁹ N m² C⁻²), q is the magnitude of the charge, and r is the distance between the dot and the charge.

1. Identify the charge's magnitude (q) and the distance from the dot to the charge (r).
2. Plug the values of q and r into the formula: E = k * |q| / r².
3. Calculate the electric field (E) using the given values and the electric constant (k).

Remember to consider the direction of the electric field, as it points away from positive charges and towards negative charges.

To know more about electric field click on below link:

https://brainly.com/question/15800304#

#SPJ11

Ice floats in liquid water because it is less dense than liquid water. When water freezes, the molecules form a crystalline structure that spaces them out more than in the liquid state. This increase in space between the molecules causes the density of ice to be less than that of liquid water. As a result, ice floats on the surface of liquid water. This property of water is important for aquatic life, as it allows for the formation of a stable environment beneath the surface of frozen bodies of water.

Answer:

Ice floats in liquid water because it is less dense than liquid water. This is because the hydrogen bonds that hold water molecules together in ice are more ordered and spaced farther apart than in liquid water. As a result, there is more empty space between the water molecules in ice than in liquid water, making ice less dense.

This is counterintuitive since most substances become denser as they solidify. However, water is different because of the way its molecules interact. Water molecules are polar, meaning they have a slight positive charge on one end and a slight negative charge on the other end. This allows them to form hydrogen bonds with each other, which are stronger than the van der Waals forces that hold most other substances together.

When water freezes, the hydrogen bonds between water molecules become more ordered and form a crystalline structure. This structure has empty spaces between the water molecules, which makes ice less dense than liquid water. Because ice is less dense than liquid water, it floats on top of it. This is important for aquatic ecosystems since if ice were denser than liquid water, it would sink and accumulate at the bottom of bodies of water, which could have negative effects on the organisms living there.

In radians (a) 0.1745 rad, 0.3941 rad, 1.2217 rad (b) sin(0.1745 radians), sin(0.3491 radians), sin(1.2217 radians) (c) sin(theta) equals to theta (d) slope = n, y intercept = -c

(a) To convert degrees to radians, we use the formula:

radians = degrees * (π/180)

Using this formula:

[tex]10.0 degrees = 10.0 * (\pi /180) radians = 0.1745 radians\\ 20.0 degrees = 20.0 * (\pi /180) radians = 0.3491 radians\\ 70.0 degrees = 70.0 * (\pi /180) radians = 1.2217 radians[/tex]

(b) The sine of an angle can be calculated using a calculator or a table of trigonometric functions. Using a calculator, we get:

[tex]sin(10.0 degrees) = 0.1736 = sin(0.1745 radians)\\sin(20.0 degrees) = 0.3420 = sin(0.3491 radians)\\sin(70.0 degrees) = 0.9397 = sin(1.2217 radians)[/tex]

We can see that the values of sine are very close for the angles measured in degrees and radians.

(c) When θ is small and measured in radians,[tex]sintheta[/tex] is approximately equal to θ. This can be seen from the Taylor series expansion of sinθ:

[tex]sin(theta) = theta - (theta^3)/3! + (theta^5)/5! - (theta^7)/7! + ...[/tex]

For small values of θ, the higher order terms become negligible, and we are left with sinθ ≈ θ.

(d) The equation [tex]sin (theta) = n sin fi[/tex] + c can be rearranged as:

[tex]sin theta - c = n sin fi[/tex]

Let [tex]y = sin theta - c[/tex] and [tex]x = sin fi[/tex]. Then, we have equation:

y = nx

This is a linear equation of the form y = mx + b, where m is the slope and b is the y-intercept. In this case, the slope is n and the y-intercept is -c. So, the slope of the graph is equal to n, and the y-intercept is equal to -c.

Learn more about radians here:

https://brainly.com/question/7721249

#SPJ11

In radians (a) 0.1745 rad, 0.3941 rad, 1.2217 rad (b) sin(0.1745 radians), sin(0.3491 radians), sin(1.2217 radians) (c) sin(theta) equals to theta (d) slope = n, y intercept = -c

(a) To convert degrees to radians, we use the formula:

radians = degrees * (π/180)

Using this formula:

[tex]10.0 degrees = 10.0 * (\pi /180) radians = 0.1745 radians\\ 20.0 degrees = 20.0 * (\pi /180) radians = 0.3491 radians\\ 70.0 degrees = 70.0 * (\pi /180) radians = 1.2217 radians[/tex]

(b) The sine of an angle can be calculated using a calculator or a table of trigonometric functions. Using a calculator, we get:

[tex]sin(10.0 degrees) = 0.1736 = sin(0.1745 radians)\\sin(20.0 degrees) = 0.3420 = sin(0.3491 radians)\\sin(70.0 degrees) = 0.9397 = sin(1.2217 radians)[/tex]

We can see that the values of sine are very close for the angles measured in degrees and radians.

(c) When θ is small and measured in radians,[tex]sintheta[/tex] is approximately equal to θ. This can be seen from the Taylor series expansion of sinθ:

[tex]sin(theta) = theta - (theta^3)/3! + (theta^5)/5! - (theta^7)/7! + ...[/tex]

For small values of θ, the higher order terms become negligible, and we are left with sinθ ≈ θ.

(d) The equation [tex]sin (theta) = n sin fi[/tex] + c can be rearranged as:

[tex]sin theta - c = n sin fi[/tex]

Let [tex]y = sin theta - c[/tex] and [tex]x = sin fi[/tex]. Then, we have equation:

y = nx

This is a linear equation of the form y = mx + b, where m is the slope and b is the y-intercept. In this case, the slope is n and the y-intercept is -c. So, the slope of the graph is equal to n, and the y-intercept is equal to -c.

Learn more about radians here:

https://brainly.com/question/7721249

#SPJ11

In a molecule with sp-hybridization, there are two electron groups around the central atom.

Sp-hybridization occurs when one s-orbital and one p-orbital in the valence shell of an atom mix together to form two hybrid orbitals called sp-hybrid orbitals. These hybrid orbitals are linearly oriented at an angle of 180 degrees to each other. The number of electron groups around a molecule is determined by the hybridization of the central atom. In the case of sp-hybridization, the central atom forms two sigma bonds with surrounding atoms using the two sp-hybrid orbitals, there are no lone pairs of electrons on the central atom in an sp-hybridized molecule.

Therefore, the number of electron groups in a molecule with sp-hybridization is two. Some examples of molecules with sp-hybridization include BeCl2 (beryllium chloride) and C2H2 (acetylene). In both of these molecules, the central atom forms two sigma bonds with adjacent atoms, and the molecular geometry is linear. The sp-hybridization is crucial in determining the molecule's shape and bonding properties. In a molecule with sp-hybridization, there are two electron groups around the central atom.

Learn more about hybridization at:

https://brainly.com/question/29587125

#SPJ11

(a) The critical angle for total internal reflection is given by sin(θc) = n2/n1, where θc is the angle of incidence at which total internal reflection occurs.

Substituting the given values of n1 and n2, we get sin(θc) = 1/2. Solving for θc, we get θc = 30°. Since the given incident angle 01 is greater than θc, the incident light should come from the medium with n1 to undergo total internal reflection.

(b) The evanescent field is present in both media, but its magnitude decays exponentially with distance from the interface. The amplitude of the evanescent field in medium 1 (with refractive index n1) is given by E1 = Ēei(kx x + k1z z - wt), where k1 = w/n1c is the wave vector in medium 1, c is the speed of light in vacuum, and x and z are the coordinates along the x- and z-axes, respectively. Similarly, the amplitude of the evanescent field in medium 2 (with refractive index n2) is given by E2 = Ēei(kx x + k2z z - wt), where k2 = w/n2c is the wave vector in medium 2. Since the wave vector k is continuous across the interface, we have kx = k1x = k2x, where k1x and k2x are the x-components of the wave vectors in media 1 and 2, respectively. Therefore, the evanescent field is present in both media, but its decay rate (determined by the imaginary part of the wave vector) is different in each medium.

learn more abouT speed here:

https://brainly.com/question/13943409

#SPJ4

The coil's induced emf is measured at a value of 1386T.  According to Faraday's rule, the quantity of, or the amount of induced emf, is equal to the number of coil turns times sub B over t, where sub B, as we've seen, can be represented as B times A.

The magnetic flux rate of change divided by the coil's turn count yields the induced emf in a coil.

Change of magnetic flux through a coil of wire = B -A

                                                            = 70Wb - 52Wb

                                                             = 18Wb

The magnetic flux in one turn of the coil = ϕ = BA

= 18*77

=1386T

To know more about magnetic flux visit:-

https://brainly.com/question/30858765

#SPJ1

The edge length of the square loop is 0.029 m.

The magnetic field at a point on the axis of a square loop of edge length a, carrying a current I, at a distance x from the center of the loop is given by the equation:

B = [tex](μ0/4π) * (2I/a^2) * f(x/a)[/tex]

where μ0 is the permeability of free space and f(x/a) is a dimensionless function that depends on the distance x/a. For a point on the axis at a distance x from the center of the loop, f(x/a) is given by:

f(x/a) = [([tex]√(1+y^2))/y] - (1/y^2) - [(1-y^2)/y^2(1+y^2)^(3/2[/tex])]

where y = x/a + 1/2.

Substituting the given values, we get:

5.2 × 10[tex]^(-9) T = (μ0/4π) * (2(42 A)/a^2) * f(0.47[/tex]/a)

Solving for f(0.47/a) gives:

f(0.47/a) = 1.00

Substituting this value into the previous equation, we get:

5.2 × 10[tex]^(-9) T = (μ0/4π) * (2(42 A)/a^2[/tex])

Solving for a gives:

a =   √ [tex][(μ0I)/(2πB)][/tex]

Substituting the values of μ0, I, and B, we get:

a = √[([tex]4π × 10^(-7) T·m/A) × (42 A)/(2π × 5.2 × 10^(-9)[/tex]T)] = 0.029 m

Therefore, the edge length of the square loop is 0.029 m.

learn more about   magnetic fields here:

https://brainly.com/question/14411049

#SPJ4

A Ferris wheel on a California pier is 27 m high and rotates once every 32 seconds in the counterclockwise direction. When the wheel starts turning, the angular position 75 seconds after the wheel starts turning, measured counterclockwise from the top, is 268 degrees.Speed of the Ferris wheel is 5.31 meters/second.

To solve this problem, we need to use the equation:
θ = θ₀ + ωt
where θ is the angular position, θ₀ is the initial angular position (in this case, at the very top), ω is the angular velocity (which is equal to 2π/T, where T is the period of rotation), and t is the time elapsed.
First, we need to find the period of rotation:
T = 32 seconds
Therefore, the angular velocity is:
ω = 2π/T = 2π/32 = π/16 radians/second
Now, we can find the angular position after 75 seconds:
θ = θ₀ + ωt
θ = 0 + (π/16) * 75
θ = 4.68 radians
To convert this to degrees, we can use the conversion factor:
1 radian = 180/π degrees
Therefore: θ = 4.68 ×180/π = 268 degrees
So the angular position 75 seconds after the wheel starts turning, measured counterclockwise from the top, is 268 degrees.
To find the speed v, we need to use the equation:
v = ωr
where r is the radius of the Ferris wheel (which is equal to the height of the wheel, since it starts at the top).
r = 27 meters
Therefore: v = ωr = (π/16) * 27 = 5.31 meters/second
So the speed of the Ferris wheel is 5.31 meters/second.

To learn more about speed https://brainly.com/question/13943409

#SPJ11