A factory hires a consultant to recommend ways to improve its productivity. The consultant notices that the production floor is strewn with tools and machines that are not continually in use. Which of the 5S philosophies should the consultant recommend to the management to establish better productivity?


A.
set in place
B.
sort
C.
standardize
D.
shine
E.
sustain

Answers

Answer 1

Answer:

B

Explanation:

Keep only what is used. Remove all unnecessary items. Red tag these items for review.


Related Questions

¿Qué es una restricción FACTIBLE?
El tema es sobre Programación Lineal.

Por favor no se roben los puntos, necesito una respuesta.


NO WIKIPEDIA.

Answers

Answer: A feasible solution for a linear program is a solution that satisfies all the constraints of the linear programming problem. There could be many solutions that satisfy all the restrictions. Any point in the feasible region is a feasible solution for the LPP. A feasible solution for a linear program is a solution that satisfies all the constraints.

Explanation: Hope this helps: ^

1. What are hand tools ? *
1 point
2. Give one example and one use of the following handtools I. Measuring tool II. Cutting Tool III. Striking tool *
6 points
3. Name the hand tool used to drive nails *
1 point
4. Name the hand tool used to cut plastic and metal pipes *
1 point
5. Which hand tool is used to clamp your work piece to the work table ? *
1 point
6. What are portable power tools? *
1 point
7. Name the power tools used to carryout the following operations I. Boring holes II. Cutting curves III. Sanding *
3 points
8. List three examples of stationary machines *
3 points

Answers

Answer:

Microsoft Word - Hand tools SON

why are you directed not to touch the holder or discharge tube whule the power to the supply to the gas tube is on?

Answers

Every profession has its rules and regulations. The reason why we are directed not to touch the holder or discharge tube while the power to the supply to the gas tube is on because;

The discharge tube can create about 5000 V of voltage when connected to power.

The gas discharge tubes is often very hot when used with the power supplies and one should not to touch them until they are cooled down.

We  have been taught to stay far was from a high voltage area or system and also we should not dare to touch it.

There are different reasons why we should about these high voltage system or are; The reason is that;

Because high voltages often reduce the impedance of our skin, thereby making electricity to flow through our bodies.

Learn more about Voltage from

https://brainly.com/question/1176850

can someone help showing the steps please​

Answers

Answer:

  a) 20 Ω

  b) 1 A

  c) 10 V on each

  d) 1/3 A through each

  e) 10 W in R1, 3 1/3 W in the others

  f) 20 W

Explanation:

The three 30 Ω resistors are in parallel with each other, so will have an equivalent resistance of (30 Ω)/3 = 10 Ω.

(a) The total circuit resistance is 10 Ω + 10 Ω = 20 Ω.

__

(b) All of the current supplied by the battery passes through R1. The current supplied by the battery is ...

  I = V/R = (20 v)/(20 Ω) = 1 A

__

(c) The voltage drop on R1 is (1 A)(10 Ω) = 10 v. Subtracting that from the battery voltage gives the voltage drop on the other resistors:

  20 v -10 v = 10 v . . . . drop on R2, R3, R4

__

(d) The current through resistors R2, R3, R4 is ...

  I = V/R = (10 v)/(30 Ω) = 1/3 A

__

(e) Power can be computed several ways. Here, it may be easiest to use ...

  P = VI

For R1, that is P1 = (10 v)(1 A) = 10 W

For R2-R4, that is P2-P4 = (10 v)(1/3 A) = 10/3 W = 3 1/3 W

__

(f) The total power dissipated is the total power supplied:

  P = VI = (20 v)(1 A) = 20 W

Adding up the power in the resistors, we get ...

  P = 10 W + 3·(10/3 W) = 20 W

if a population has no predadors and plenty of available resources, how might that population change

Answers

Answer:

B (exponential growth )

Explanation: wish u the best bby <33

MANUFACTURING QUESTION PLEASE HELP​

Answers

Answer:

"He then pours the metal into a mold and allows it to solidify."

Connect wires to make the correct logic outputs.


Outputs needed: ~(B&C), A.


(Assignment: NAND Gates.

School Program: Acellus.

Class: Electronics & Coding.)

Answers

Answer:

Explanation:

im dum sorry bro i don't know it im in 6 grade

All of the following are examples of capital intensive industries EXCEPT: *
1 point
Soft drink production
oil extraction
manufacturing
hospitality

Answers

Answer:

hospital

Explanation:

Soft drink production is a capital intensive industry as it's depends upon the economy and trade.Oil extraction is a national industry and it also involves the intention of trade.Manufacturing is similar to soft drink production and has intense of trade.Hospital doesn't has the intention of trade so it's the answer

what are some benfits of getting involved with 4h

Answers

Answer:

the kids can get smarter and make the country where they live better

4h can help with making the next generation better, and better if we help them

Please help me do this with my exam tomorrow.
Indicate the target item of the time to use, preserve and turn it in time. In your family and locality, what methods of harvesting, management and processing do you apply? Ex example

Answers

Answer:

ddddddddddddddddddddddddddddd

Explanation:

cccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccc

How much current is drawn by a flashlight that has a resistance of 10 ohms if a voltage of 3 volts is impressed across it?

Answers

Answer:

0.3 amps

Explanation:

amps can be found using the equation

current=volts/resistance

so current=3V/10Ohms=0.3 amps

Situation: Peter is designing a new hybrid car that functions on solar power. He is currently working on sketches of his design using geometric patterns and shapes.

Answers

Answer:

whats the question?

Explanation:

WHICH LUBRICATION SYSTEM RECEIVES OIL FROM THE OIL SUPPLY TANK, PRESSURIZES THE OIL, SENDS THE OIL THROUGH THE FILTER AND DELIVERS THE OIL TO THE BEARINGS

Answers

Answer:

The following is the answer.

Explanation:

PRESSURE SYSTEM.


(b) The application of user centred design can lead to innovative products such as the umbrella shown in Figure 9.

Explain the concept of user centred design and how it may have influenced the design of the umbrella shown in Figure 9. (6 marks)

Answers

Answer:

the concept of user centred design is the idea of putting your clients best needs in mind. you need to be empathic and understanding of how to make their life easier. by doing research you can do this. for example the design in figure 9 shows an umbrella with a canopy. the canopy can deflect rain and still have the easy design of an umbrella. this makes it not only easier to use but functional.

Explanation:

i wrote this myself so copy it or just rewrite it, it doesnt matter

Many amateur video games suffer from what kind of layout?
A. an overly neutral layout
B. an overly simplistic layout
C. an over-crowded layout
D. a boring layout

Answers

Answer:

D a boring layout I think but you welcome

What best describes the relationship between missionaries and Native Americans?

Answers

Answer:

Missionaries taught the Native Americans to read but allowed them to keep their customs. Native Americans and missionaries fought in battles

Explanation:

sorry if this doesn't help u but i hope it does!

1. Write an equation that shows the equivalency between meters and Gigameters.

Answers

The equation is below:
10^9 m = 1 Gm

why is a plastic or metal restrictor placed in either the end of the vent pipe or in the vapor-vent hose on some vehicles?

Answers

Answer:

To help the vehicle better function

Explanation:

The plastic or Metal material there is to block certain things that shift our of place and can get caught up in the vent, the materials prevent thing from entering in and out of the vent bc if anything should go in the vent it can cause severe vehicle problems

Hope this help❤

Which is NOT an example of labour intensive industry?

Healthcare practitioner
steel production industry
local farmers
small cakery

Answers

Answer:

small cakery

Explanation:

it only makes food it does not cut logs, wood etc.

Answer:

small cakery

Explanation:

cakery or bakery don't require labour services almostThere hardly one or two person works so it can't be called labour intensive industry

Write a system of equations to describe the situation below, solve using any method, and fill in the blanks.

Nicole and Josie are both selling cookie dough for a fundraiser. Although Nicole has already sold 4 tubs, Josie hasn't sold any yet. If Nicole starts selling 5 tubs per day and Josie begins selling 6 tubs per day, they will eventually sell the same amount of cookie dough. How many tubs will each sell? How many days will that take?


Nicole and Josie will each sell
tubs of cookie dough in
days.

Answers

The number of tubs that each of them sold is; 24 tubs each

The number of days it will take for both of them to sell same amount of tubs is; 4 days

Number of cookies that Nicole had already sold = 4 tubs

Number of cookies sold by Josie before counting = 0 cookies

Nicole now sells 5 tubs per day and

Josie now sells 6 tubs per day.

Let the number of days it will take for them to have sold the same amount of cookies be d.

Thus;

5d + 4 = 6d + 0

6d - 5d = 4

d = 4 days

Thus, total number of cookies for both are;

Total for Nicole = 4 + 5(4) = 24 cookies

Total for Josie = 6(4) = 24 cookies

Read more about proportion at; https://brainly.com/question/870035

John has an exhaust leak in his Acura Integra GS-R, What steps would he take to fix the leak in time for his inspection?

Answers

Answer:

Explanation:

Fist you need to identify where the leak is coming from. You can do this by either listening for the leak or spraying soapy water on the exhaust to look for air bubbles coming out of the exhaust. Depending on the spot of the leak there are many ways you can fix this leak.

1. Exhaust clamp

2. Exhaust putty

3. Exhaust tape

4. New exhaust

Exhaust clamp is best used for holes on straight pipes.

Putty is best used on welds or small holes like on exhaust manifolds or welds connecting various pieces like catalytic converters, mufflers, or resonators.

Tape will work best on straight pipes with holes.

New exhaust is for when the thig is beyond repair, like rust.

Now good luck because working on exhausts is a pain.

True of false an understaffed store can cause loss of inventory

Answers

Answer:

probably true, if it's understaffed people are more likely to steal and the overworked workers that still remain are likely to make more mistakes

True.

It's important to keep a balance of store labor with incoming consumer traffic. Understaffing affects the impact of profitability.

what are the potential problems with the ag gag laws

Answers

Answer:

Ag-gag laws pose a threat to a wide spectrum of values and issues Americans care about. Social issues potentially negatively impacted by ag-gag laws include, but are not limited to: Animal Welfare. Food Safety.

Explanation:

How do robots demonstrate the modern, technological Japan? *



Answers

Robots demonstrate modern, technological Japan because it serves as brought economical success to Japan since it help them to build products faster and efficiently.

According to the question, we are to discuss how the robot help japan in terms of technology and modernization.

As a result of this we can see that Japan is moving forward in technology with development of robot because it makes them to build more products.

Therefore, Robot has  brought economical success to Japan

Learn more about robot at:

https://brainly.com/question/10387419

Please help for our stem project :(

Explain how Ratio and proportion affect the strength of the Bridge.

STEM Project

Answers

Answer:

Do you have some a picture

What is the voltage across the load, RL, in
this voltage divider network?
10.25 V
4.55 V
5.71 V
11.50 V

Answers

Answer:

  (c)  5.71 V

Explanation:

The circuit can be redrawn to a Thevenin equivalent that is 6V through a 5-ohm resistor into a 100-ohm load. Then the voltage at the load is ...

  (6 V)(100/(100 +5) ≈ 5.71 V

Gasoline has a comparatively high Btu per gallon rating of around
Select one:
O a. 1 lb: 2°F
O b. 5,000 Btu
O c. 12,000 Btu
O d. 14.000 Btu

Answers

Answer:

A

Explanation:

Gasoline has a comparatively high Btu per gallon rating of around 1 lb: 2°F. GGE enables customers to contrast the energy value of competing fuels with gasoline, a widely used fuel. Thus, option A is correct.

The term "gasoline gallon equivalent" (GGE) or "gasoline-equivalent gallon" (GEG) refers to the volume of an alternative fuel needed to produce one liquid gallon of gasoline's equivalent amount of energy.

If fuels are offered in various quantities and in various physical forms, it is challenging to compare the price of gasoline with other fuels. GGE tries to address this. The energy content of one gallon of gasoline is exactly equal to that of one GGE of CNG and one GGE of electricity. GGE does this by directly contrasting gasoline with other alternative fuels, such as those offered as gas (natural gas, propane, and hydrogen) and as metered electricity.

Therefore, option A is the ideal selection.

Learn more about the gasoline gallon equivalent" (GGE) here:

https://brainly.com/question/31491497

#SPJ5

true or false tensile forces are smaller in arch bridges

Answers

Answer:

True

Explanation:

The tensile forces are small in most arches and usually negligible.

A technician notes that an operating air-conditioning system has ice formed on the suction line at the condensing unit. The technician can reasonably assume that:

Answers

The technician can reasonably assume that evaporator coil is frozen over.

An air-conditioning system makes a place cooler by absorbing heat from the

surrounding. This is usually done with the aid of the evaporator coil.

In situations whereby there are ice particles formed on the suction line at the

condensing unit then it means the air conditioning system is faulty and must

be turned off to prevent damage to other parts.

Read more about Air conditioning system here https://brainly.com/question/24920322

what element is the primary constituent of ferrous alloys?

Answers

what element is the primary constituent of ferrous alloys?
Answer: Ferrous alloys or metals are metals that consist mostly of iron (Fe). Steel is an iron-based alloy containing typically less than 1% carbon, where iron frequently contains 2% or more carbon.
Other Questions
Factorise the following expressions.a + 8a + 16 Which of the following includes organisms that can use energy from the sun to make food? Sarah is 2 inches taller than the quotient of billys height and 5. Let b represent Billys height. write an expression that represents Sarahs height Name of the first lasting English settlement in North America? What could be a good option available to you if you arebehind on loan payments? Please some urgent help!!!! Which statements always apply to the process of diffusion? check all that apply. The shortest route from London to Swansea is 180 miles. A lorry is expected to take 4.5 hours to travel this route. The lorry actually travels by a different route which increases the distance by 15%, but it still arrives in 4.5 hours. By how many more mph than the expected speed does the lorry travel? Please show any steps you used to solve the equation!Solve the equation [tex]sec(theta)=2 \\0\leq theta\ \textless \ 2\pi[/tex]I'll mark brainliest if correct! HELP ME PLEASE ASAP.. only if you know SPANISH PLS !! In the supply-and-demand schedule shown above, at the equilibrium price, quantity supplied is _____ and quantity demanded is _____.A. 50, 350B. 450, 75C. 200, 200 plsss help mee i donot now the answerActivity 1: Identifying Hypothesis and Conclusion Directions: Identify the hypothesis and the conclusion for each of the following statements. 1. If you live in Manila, then you live in the Philippines. 2. If a triangle is a right triangle, then one of its interior angle is a 90-degree angle. 3. A square is not a triangle. 4. An even number is divisible by 2. 5. The measure of an acute angle is less than 90. I cannot figure this out. Any help would be appreciated. in the image above, a stream from the land on the right enters the ocean on the left in the lower part of the picture, and another does the same near the top of the picture. what happened where the streams met the ocean? 12>-2(y-4) solve the inequality I'm writing a short story about a clown stalking a little girl, it's not finished but can anyone give me a suggestion on what to change in the writing and maybe come up with an ending cause I'm having a bit of trouble.In October of 2016, a twelve-year-old girl named Samantha lived in a suburban town, after school her friend invited her to a Halloween party later at night. She accepted her request but of course like every other kid, they had to get permission. She later came home and asked their parents if she could come to the party, short answer...no. Samantha tries to argue with them but, no luck. Later in the evening, Samantha was getting frustrated. Then she thought I could sneak out of the house while mom and dad are sleeping., and so thats what she did. A few hours later she started to get ready, wearing her witch costume. She quietly sneaks out of her room into the hallway, the wooden floor creaking. She gets to the front door, walks out of the house, and slowly shuts the door. She looked around, seeing the streets were completely empty. She began walking down the street, slowly realizing she didn't know where she was going. After about a few minutes she was completely lost: didn't know her way back home, nor which direction to take. The fear of being alone crept up to her. All of a sudden she hears a bit of laughter coming from behind her. She turns around, her eyes widening as she sees a tall man in a clown costume, looking at her with a sinister smile. Samantha didn't know what to do, she quickly started to walk away, the clown follows. She yells, "Back off creep!". She started running, so did the clown chasing after her. She yelled and screamed for help, nobody was around. She gets to a nearby park losing sight of the clown. She hides behind a tree not knowing what to do. She peeks around seeing him, wandering around looking for her. She was trembling in fear, being cold and alone. Then she heard sirens in the distance and the clown immediately runs away. The midpoint M of ST has coordinates (5, 5). Point T has coordinates (9,5). Find thecoordinates of point S. during which phase of mitosis are the spindle fibres formed around the sister chromatids? Mendeleev's arrangement of the periodic table was in order of increasing ____. A. atomic number B. atomic mass C. neutron number D. valence electron number What force is responsible for how magma flows and rocks stack up on top of one another?Question 6 options:Electroweak and StrongNuclearElectromagneticGravitational