A car battery has a voltage of ε = 12 V. To turn the starter on a car the battery must supply I = 274 A. It takes t = 4.9 s for the engine to start.
How much energy did the starter consume, E, in J?

The energy of a photon of green light with a wavelength of 550 nm is approximately 3.58 x 10^-19 J or 2.23 eV. The wave number of the photon is approximately 1.82 x 10^7 m^-1.

The energy of a photon is given by the equation E = hc/λ, where h is Planck's constant (6.626 x 10^-34 J s), c is the speed of light (2.998 x 10^8 m/s), and λ is the wavelength of the photon. Substituting these values, we get E = (6.626 x 10^-34 J s x 2.998 x 10^8 m/s) / (550 x 10^-9 m) = 3.58 x 10^-19 J.

To convert joules to electron volts, we use the conversion factor 1 eV = 1.602 x 10^-19 J. Thus, the energy of the photon in electron volts is Eev = E / (1.602 x 10^-19 J/eV) = 2.23 eV.

The wave number of a photon is given by the equation k = 2π/λ. Substituting the wavelength, we get k = 2π / (550 x 10^-9 m) = 1.82 x 10^7 m^-1.

For more questions like Light click the link below:

https://brainly.com/question/10709323

#SPJ11

If the spring supports 18 kg without reaching its elastic limit, then it will stretch up to 65.4 cm.

To answer your question, we will use Hooke's Law and the concept of the spring constant.

First, let's find the spring constant (k) using Hooke's Law. Hooke's Law states that the force acting on a spring (F) is directly proportional to the displacement (x) from its equilibrium position:

F = kx

Given that the spring stretches 2.4 cm (0.024 m) when supporting a mass of 0.66 kg, we can find the force (F) using the formula F = mg, where m is the mass and g is the acceleration due to gravity (approximately 9.81 m/s²):

F = (0.66 kg)(9.81 m/s²) = 6.4746 N

Now, we can find the spring constant (k):

6.4746 N = k(0.024 m)
k = 269.775 N/m

Next, we want to find how far the spring will stretch when supporting a mass of 18 kg. Again, we will use Hooke's Law. First, find the force (F) for the 18 kg mass:

F = (18 kg)(9.81 m/s²) = 176.58 N

Now, use Hooke's Law to find the new displacement (x):

F = kx
176.58 N = (269.775 N/m)x
x = 0.654 m

Finally, convert x to centimeters:

x = 0.654 m * 100 cm/m = 65.4 cm

So, when the spring supports a mass of 18 kg and the elastic limit is not reached, it will stretch 65.4 cm.

Learn more about Hooke's Law:

https://brainly.com/question/2648431

#SPJ11

The response D is correct as hot water has more energy than cold water, causing the molecules to move faster, leading to faster dissolution.

Hot water dissolves substances faster than cold water due to its higher energy level. The heat energy causes the water molecules to move faster, which increases the kinetic energy of the particles in the substance being dissolved. This therefore raises the probability of particle collisions, which accelerates the rate of disintegration.

Additionally, the stronger intermolecular forces between the water molecules make it easier for the solute particles to dissolve due to their increased energy level. This is why substances dissolution occurs faster in hot water than cold water.

To know more about solubility, visit,

https://brainly.com/question/23946616

#SPJ1

Complete question - Zeplin is investigating how long different substances take to dissolve in water. He timed how long each tested substance took to dissolve twice: once in cold water, and once in hot water. He noticed they dissolved faster in the hot water for every test. Which statement explains why this happened?

Responses:

A Hot water has more volume than cold water, so substances spread to fill space.

B Hot water has more gravity than cold water, so particles break up more quickly.

C Hot water has more oxygen than cold water, and oxygen absorbs substances.

D Hot water has more energy than cold water, causing the molecules to move faster.

The ratio of the energies stored in the combination, before and after the introduction of the dielectric slab is (5/3) times the dielectric constant 'K'.

Before the introduction of the dielectric slab, the energy stored in the combination of capacitors can be calculated using the formula:

E = (1/2) * C1 * V^2 + (1/2) * C2 * V^2

Substituting C1 = 2C2, we get:

E = (1/2) * 2C2 * V^2 + (1/2) * C2 * V^2

E = (3/2) * C2 * V^2

After the introduction of the dielectric slab, the capacitance of each capacitor increases by a factor of K. Therefore, the new capacitances are C1' = 2KC2 and C2' = KC2.

The energy stored in the combination of capacitors with the dielectric slab can be calculated using the same formula:

E' = (1/2) * C1' * V^2 + (1/2) * C2' * V^2

Substituting the new capacitance values, we get:

E' = (1/2) * 2KC2 * V^2 + (1/2) * KC2 * V^2

E' = (5/2) * KC2 * V^2

Taking the ratio of the energies, we get:

E'/E = [(5/2) * KC2 * V^2]/[(3/2) * C2 * V^2]

E'/E = (5/3) * K

Also, to find the ratio of the energies stored in the combination of capacitors before and after the introduction of the dielectric slab, follow these steps:

1. Find the initial total capacitance (C_total_initial) when the capacitors are connected in parallel:
C_total_initial = C1 + C2

2. Calculate the initial energy stored (U_initial) in the combination of capacitors:
U_initial = (1/2) * C_total_initial * V^2

3. When the dielectric slab is inserted, the capacitance of each capacitor increases by a factor of 'K'. So, the new capacitances are:
C1_new = K * C1
C2_new = K * C2

4. Calculate the new total capacitance (C_total_new) when the dielectric slab is inserted:
C_total_new = C1_new + C2_new

5. Calculate the new energy stored (U_new) in the combination of capacitors after inserting the dielectric slab:
U_new = (1/2) * C_total_new * V^2

6. Finally, find the ratio of the energies stored before and after the introduction of the dielectric slab:
Energy_ratio = U_new / U_initial

By following these steps, you can find the ratio of the energies stored in the combination of capacitors before and after the introduction of the dielectric slab.

Learn more about dielectric slab here: brainly.com/question/12915112

#SPJ11

Refer to the attached image.

(a) The initial velocity is 0 m/s.

(b) The final velocity at t=6s, is 10 m/s.

(c) The average acceleration is 1.67 m/s².

Instantaneous velocity is a measure of how fast an object is moving at a particular moment in time. It is the velocity of an object at a specific instant or point in time, and it is typically represented as a vector with both magnitude and direction.

The initial velocity = 0 m/s

The velocity of the particle at time, t = 6 seconds = displacement/time

velocity = 60 m/ 6s = 10 m/s

The average acceleration = (v₂ - v₁) / (t₂ - t₁)

average acceleration = (10 m/s - 0 m/s )/ (6 s - 0 s) = 10/6 = 1.67 m/s²

Learn more about instantaneous velocity here: https://brainly.com/question/2234298

#SPJ1

(a) The initial velocity is 0 m/s.

(b) The final velocity at t=6s, is 10 m/s.

(c) The average acceleration is 1.67 m/s².

Instantaneous velocity is a measure of how fast an object is moving at a particular moment in time. It is the velocity of an object at a specific instant or point in time, and it is typically represented as a vector with both magnitude and direction.

The initial velocity = 0 m/s

The velocity of the particle at time, t = 6 seconds = displacement/time

velocity = 60 m/ 6s = 10 m/s

The average acceleration = (v₂ - v₁) / (t₂ - t₁)

average acceleration = (10 m/s - 0 m/s )/ (6 s - 0 s) = 10/6 = 1.67 m/s²

Learn more about instantaneous velocity here: https://brainly.com/question/2234298

#SPJ1

The x-component of the electric field at (x=0,y=0,z=0) at t=0 cannot be determined without additional information.

In order to determine the x-component of the electric field at (x=0,y=0,z=0) at t=0, we would need more information about the electromagnetic wave.

The electric and magnetic fields are perpendicular to each other and both are perpendicular to the direction of wave propagation.

Therefore, we would need to know the direction of propagation in order to determine the orientation of the electric and magnetic fields.

Without this information, it is impossible to determine the x-component of the electric field at a specific point in space and time.

For more such questions on electric field, click on:

https://brainly.com/question/14372859

#SPJ11

The turbine from rest to 180 rad/s in 27 s

The inlet, gas turbine engine, which consists of a compressor, combustion chamber, and turbine, and exhaust nozzle are the individual parts of a turbojet engine. Through the inlet, air is taken into the engine, where it is heated and compressed by the compressor.

τ_avg = ΔL / Δt

where ΔL is the change in angular momentum, which can be calculated using:

ΔL = Iω - I(0)

where I(0) is the initial moment of inertia, which we can assume to be zero.

Substituting the given values, we get:

ΔL = Iω = (1/2)Iω² = (1/2) * (180 rad/s)² * I

τ_avg = ΔL / Δt = (1/2) * (180 rad/s)² * I / 27 s

To know more about turbine visit:-

https://brainly.com/question/14582343

#SPJ1

the de Broglie wavelength of the baseball is approximately 1.05 x 10^-34 meters.

The de Broglie wavelength of an object is given by the equation λ = h/mv, where h is Planck's constant (6.626 x 10^-34 J s), m is the mass of the object, and v is its velocity. Plugging in the given values for the baseball, we get:
λ = (6.626 x 10^-34 J s)/(211 g x 0.0310 m/s)
λ = 9.74 x 10^-35 m
Therefore, the de Broglie wavelength of the baseball is approximately 9.74 x 10^-35 meters.
Hi! To calculate the de Broglie wavelength of a 211 g baseball moving at 31.0 m/s, you'll need to use the de Broglie wavelength formula:
λ = h / (mv)
where λ represents the de Broglie wavelength, h is the Planck's constant (6.626 x 10^-34 Js), m is the mass of the object (211 g converted to kg), and v is its velocity (31.0 m/s).
First, convert the mass to kg: 211 g * (1 kg / 1000 g) = 0.211 kg
Now, plug the values into the formula:
λ = (6.626 x 10^-34 Js) / (0.211 kg * 31.0 m/s)
λ ≈ 1.05 x 10^-34 m

Learn more about wavelength  here:

https://brainly.com/question/31143857

#SPJ11

the value of the inductance L is 1.8 * 10^-4 H (henries).

To find the value of the inductance L, we can use the formula:

Vrms = Ipk * sqrt(2) * w * L

Where Vrms is the rms voltage (9.0 V), Ipk is the peak current (60 mA), sqrt(2) is a constant factor, w is the angular frequency (2 * pi * f), and f is the frequency (20 kHz).

Plugging in the values, we get:

9.0 = 60 * 10^-3 * sqrt(2) * 2 * pi * 20 * 10^3 * L

Simplifying, we get:

L = 9.0 / (60 * 10^-3 * sqrt(2) * 2 * pi * 20 * 10^3) = 1.8 * 10^-4 H
Here you can learn more about inductance

https://brainly.com/question/18575018#

#SPJ11  

The permeability of free space (4pi10^-7 N/A^2) and the limits of integration are from x = -0.009 m to x = 0.009 m, since the midpoint of the unshielded section is at x = 0.

It has magnitude at a point P that is radially separated from the wire by r. B = μ0I/(2πr). This equation is derived from Ampere's law, one of Maxwell's equations. The permeability of open space is defined as the ratio 0 = 4*10-7 N/A2. Ns/(Cm) = Tesla is the magnetic field's SI unit (T).

To find the expression for the magnitude of the differential magnetic field, dB, at point 4 due to the current in the wire segment dl, we can use the Biot-Savart law.

Let r be the distance from the wire segment dl to point 4

dB = (mu_0/4*pi) * (I * dl * sin(theta)) / r²

where mu_0 is the permeability of free space (4pi10⁻⁷ N/A²).

(b): To perform the indefinite integral of the expression we found in part (a), we need to integrate over the entire unshielded length of the wire, which is x = 0.018 meters long. We have:

B = ∫dB = ∫(mu_0/4*pi) * (I * dl * sin(theta)) / r²

To know more about permeability visit:-

https://brainly.com/question/29857641

#SPJ1

Question:

Arabbit has eaten the foil shielding off of a power cable that carries a DC current of I= 0.41At0 the amplifier for your outdoor speaker system The shielded parts of the wire do not contribute to the magnetic field outside the wire. The unshielded part of the wire is x = 0.018 meters long; Point 4 is exactly above the midpoint of the unshielded section; distance x/2 above the wire The current flows to the right as shown; which should be taken a5 the positive direction: The small length of wire, dl, a distance from the midpoint of the unshielded section of the wire, contributes a differential magnetic field dB, at point 4

Race as a socio-historical construct, highlights the importance of understanding the social, political, and economic contexts in which race is created and maintained.

According to Michael Omi and Howard Winant, in "Racial Formations," race is a socio-historical concept that is constructed through the intersection of cultural, political, and economic forces.

In this book, they argue that race is not an immutable, biologically determined characteristic of individuals or groups but rather a social construct that is created and maintained through systems of power and inequality. The authors illustrate how race is constructed through examples from different historical periods and social contexts.

Learn more about race here: https://brainly.com/question/28138343

#SPJ1

The inside of the sun is hotter than the surface of the sun.

The sun's core, where nuclear fusion occurs, has a temperature of approximately 15 million degrees Celsius, while the surface, known as the photosphere, is around 5,500 degrees Celsius. The significant difference in temperature is due to the energy generation process at the core, which involves the fusion of hydrogen atoms to form helium. This process releases a tremendous amount of heat and light, causing the core to be significantly hotter than the surface.

As we move outwards from the core, the temperature decreases gradually through the radiative and convective zones. The radiative zone is where energy moves through radiation, while the convective zone involves the movement of heat through convection currents. The cooler, less dense plasma rises to the photosphere and then sinks back down as it cools, creating a continuous cycle.

In summary, the inside of the sun is hotter than its surface due to the nuclear fusion process occurring at the core. The temperature decreases as we move outward from the core through the radiative and convective zones, eventually reaching the surface, which is cooler and denser in comparison.

know more about nuclear fusion here:

https://brainly.com/question/982293

#SPJ11

a) To solve the problem for n = 5, we can start by turning off light 5. Then, we turn off light 4 by turning on light 5 (since it was the only light on) and then turning off light 4. We repeat this process for lights 3 and 2, until all the lights are off. Therefore, it takes 4 moves to turn all the lights off for n = 5.

b) To find the number of moves required to turn all n lights off for any n, we can use a recurrence relation. Let M(n) be the number of moves required to turn off n lights.

If we consider the last light, light n, it can only be turned off if all the preceding lights (1 through n-1) are off. This means that we need to turn off all n-1 lights before we can turn off light n.

Once we turn off all n-1 lights, we can turn off light n with one move. Therefore, the total number of moves required to turn off all n lights is M(n-1) + 1.

Using this recurrence relation, we can find the number of moves required for any value of n. For example, for n = 5, we can calculate:

M(5) = M(4) + 1
M(4) = M(3) + 1
M(3) = M(2) + 1
M(2) = M(1) + 1
M(1) = 1

Substituting these values, we get:

M(2) = 2
M(3) = 3
M(4) = 4
M(5) = 5

Therefore, the number of moves required to turn off all 5 lights is 5, which matches the answer we found earlier.

In general, the recurrence relation for the number of moves required to turn off n lights is:

M(n) = M(n-1) + 1, with initial condition M(1) = 1.

Visit https://brainly.com/question/31478312 to know more about recurrence

#SPJ11

According to the given question, a force of 8 N is applied at an angle of 150 degrees with respect to the displacement of a 12 kg box. This means that the force is not being applied in the same direction as the displacement of the box.

In order to calculate the work done, we need to first determine the component of the force in the direction of the displacement. To do this, we can use trigonometry to find the cosine of the angle between the force vector and the displacement vector.

Once we have this value, we can multiply it by the magnitude of the force and the distance traveled to get the work done. It is important to note that work is a scalar quantity and is measured in joules.

Therefore, the final answer will be in joules. In this case, the work done will be less than if the force was applied in the same direction as the displacement.

To know more about displacement refer here:

https://brainly.com/question/11934397#

#SPJ11

The mass moment of inertia of the racket about the y-axis through O is approximately 0.000473 kg m

To calculate the mass moment of inertia of the racket about the y-axis through O, we can divide the racket into several small elements and use the parallel axis theorem to add up their individual moments of inertia.

Let's consider a small element of length ΔL at a distance y from the y-axis. The mass of this element is:

Δm = r ΔL

The moment of inertia of this element about the y-axis through its center of mass is:

ΔI = [tex](Δm y^2)/3[/tex]

Using the parallel axis theorem, the moment of inertia of this element about the y-axis through O is:

ΔI' = ΔI + Δm ([tex]d-y)^2[/tex]

where d is the distance from the center of mass of the element to point O.

Substituting the expressions for ΔI and Δm, we get:

ΔI' = (r ΔL[tex]y^2)/3 + r ΔL (d-y)^2[/tex]

The total mass moment of inertia of the racket about the y-axis through O is the sum of the moments of inertia of all the small elements:

I = ∑ ΔI' = ∑ [(r ΔL y[tex]^2)/3 + r ΔL (d-y)^2][/tex]

We can approximate the shape of the racket by dividing it into small rectangles of width Δx and length L. The height of each rectangle can be calculated using the given dimensions of the racket. Let's call the height of a rectangle at a distance y from the y-axis h(y).

We can express h(y) as a function of y using the equation of the curve that defines the shape of the racket. The curve can be approximated by a parabola:

h(y) = [tex]ay^2 + by[/tex]

where a and b are constants that can be determined from the given dimensions of the racket. At y = 0, h(y) = 0. Therefore, b = 0. At y = 0.15 m, h(y) = 0.025 m. Substituting these values, we get:

0.025 = [tex]a (0.15)^2[/tex]

Solving for a, we get:

a = 0.037

Therefore, the height of a rectangle at a distance y from the y-axis is:

h(y) = 0.037 [tex]y^2[/tex]

The distance d can be approximated as the distance from the center of a rectangle to point O. Since the rectangles are uniform, the center of mass of each rectangle is at its midpoint. Therefore, d is half the length of the rectangle:

d = L/2

Substituting the expressions for h(y), d, and ΔL, we can express the total mass moment of inertia of the racket as an integral:

I = [tex]∫ [(r h(y) Δx y^2)/3 + r h(y) Δx (L/2-y)^2] dy[/tex]

The limits of integration are from -0.075 m to 0.075 m, since the width of the racket is 0.15 m.

Substituting the expressions for h(y) and d, and simplifying the integrand, we get:

[tex]I = (r Δx L^3)/36 ∫ y^2 + (L/2-y)^2 dy\\I = (r Δx L^3)/18 ∫ (y-L/4)^2 dy\\I = (r Δx L^5)/480[/tex]

Substituting the given values of r and L, we get:

I = 0.000473 kg m[tex]^2[/tex]

Therefore, the mass moment of inertia of the racket about the y-axis through O is approximately 0.000473 kg m

To know more about accelerating here

https://brainly.com/question/460763

#SPJ4

If a 38.0-turn, 5.70-cm-long solenoid generates a magnetic field with a magnitude of 2.20 mt at its center, the current in the solenoid is 0.726 A.

The magnetic field of a solenoid is calculated as follows:

B = μ₀ * n * I,

The answer to the question is that L = 5.70 cm, B = 2.20 m, and T = 2.20 T, N, and turns equal 38.0. As a result, after plugging these values into the formula above, we get:

4.20 x T*m/A * (38.0 / 0.0570 m) * 2.20 x T

With the data above, we can now determine the current as follows:

I = (2.20 x T) / [(4 x T*m/A) * (38.0 / 0.0570 m)] = 0.726 A

As a result, 0.726 A of current is flowing through the solenoid.

A solenoid is made out of a large coil of wire with several turns. When a current passes through it, it creates an almost homogeneous internal magnetic field. Because they can convert electrical current into mechanical action, solenoids are widely used as switches.

To learn more about solenoid visit:

brainly.com/question/3821492

#SPJ1

The mass of the box is 11.8 kg.

We can use Newton's second law, which states that the net force on an object is equal to its mass times its acceleration:

F_net = ma

In this case, the fisherman applies a horizontal force to the box, and the box accelerates in the same direction. Since there is no friction, the net force on the box is equal to the force applied by the fisherman:

F_net = 42.5 N

The acceleration of the box is given as 3.60 [tex]m/s^2[/tex]. We can now solve for the mass of the box by rearranging the formula:

m = F_net / a

Substituting the given values, we get:

m = 42.5 N / 3.60[tex]m/s^2[/tex]

m = 11.8 kg

Therefore, the mass of the box is 11.8 kg.

Learn more about mass

brainly.com/question/19694949

#SPJ11

True. The index of refraction is a measure of how much a medium can slow down light as it passes through it. The higher the index of refraction, the more the light will be slowed down, resulting in a slower speed of light within the medium.

The index of refraction is a fundamental property of a material that describes how much it can bend and slow down light as it passes through it. It is defined as the ratio of the speed of light in a vacuum to the speed of light in a medium. When light passes from one medium to another, its speed and direction can change due to the change in the index of refraction. The degree of change in the direction of light is proportional to the difference in the index of refraction between the two materials. The higher the index of refraction of a material, the more it can bend and slow down light, resulting in a reduced speed of light within the medium. This property is important in many applications, such as lenses, prisms, and optical fibers.

learn more about index of refraction here:

https://brainly.com/question/23750645

#SPJ11

Move an object from the ground onto a stand without moving the vehicle, the boom operator should retract hydraulic  A and extend hydraulic cylinder.

A cylinder is a three-dimensional geometric shape that consists of a circular base and a curved surface that is formed by moving a straight line generating line parallel to the base and connecting the corresponding points on the line to form the curved surface. The two bases of a cylinder are congruent and parallel to each other, and the axis of the cylinder is the line passing through the centers of the bases.

To know more about cylinder visit :

https://brainly.com/question/16134180

#SPJ1

The focal length (f) of the magnifier needed to view the 2.60 mm long insect with an angular size of radians, , the required focal length for the magnifier is approximately 102.6 mm.

We can use the formula:

magnification = (image distance)/(object distance) = (1 + focal length)/(focal length)

where the magnification is given by the angular size of the image divided by the angular size of the object:

magnification = (angular size of image)/(angular size of object)

In this case, we want the angular size of the image to be 2.80×10−2 radians and the length of the object (the insect) is 2.60 mm. We can convert the length to meters (since the angular size is given in radians) by dividing by 1000:

object size = 2.60/1000 = 2.6×10−3 m

Now we can solve for the focal length:

magnification = (angular size of image)/(angular size of object) = (2.80×10−2)/(2.6×10−3) = 10.77

magnification = (1 + focal length)/(focal length)

10.77 = (1 + f)/(f)

10.77f = 1 + f

9.77f = 1

f = 0.1026 m = 102.6 mm

Therefore, the required focal length is 102.6 mm.

Learn more about focal here:'

https://brainly.com/question/16188698

#SPJ11

For the Moon to maintain its elliptical orbit around the Earth, a centripetal acceleration of around  [tex]0.027 m/s^2[/tex].

The Moon's orbital radius around the Earth is approximately 384,400 km, or or [tex]3.844 \times 10^8[/tex] meters.

The following equation may be used to determine the Moon's orbital velocity:

V = 2πR / T

where T denotes the Moon's orbital period around the Earth.

The Moon orbits the Earth at a period of around 27.3 days, or [tex]2.36 \times 10^6[/tex] seconds.

When we solve for V by substituting the values of R and T into the equation, we obtain:

[tex]V = 2\pi (3.844 \times 10^8 m) / (2.36 \times 10^6 s) = 1022.7 m/s[/tex]

When we solve for V by substituting the values of R and T into the equation, we obtain:

[tex]ac = (1022.7 m/s)^2 / (3.844 \times 10^8 m) = 0.027 m/s^2[/tex]

Centripetal acceleration is always perpendicular to the object's motion and is aimed at the circle's centre. This indicates that it modifies the object's direction rather than its speed. The formula provides the magnitude of the centripetal acceleration  [tex]a = v^2 / r[/tex], where r is the circumference of the circular route and v is the object's speed.

Since it governs the motion of many items in our daily lives, centripetal acceleration is a crucial idea in physics. Centripetal acceleration, for instance, is responsible for the rotation of a car's tyres while cornering as well as the motion of planets in their orbits around the sun. Centripetal acceleration is not present, instead of moving in a curved route, these things would move in a straight line.

To learn more about Centripetal acceleration visit here:

brainly.com/question/14465119

#SPJ4

To calculate the electric potential (V) at the point where the electric potential energy of a 10 nC charge is 36 mJ, we can use the formula: V = U / q where U is the electric potential energy and q is the charge.

So, we have:

V = U / q = 36 mJ / 10 nC

Converting mJ to J and nC to C, we get:

[tex]V = (36 × 10^-3 J) / (10 × 10^-9 C) = 3.6 × 10^7 V[/tex]

Therefore, the electric potential at this point is 3.6 × 10^7 volts.

If a 20 nC charge were placed at this point, its electric potential energy (U) would be:

U = q × V = 20 nC × 3.6 × 10^7 V

Converting nC to C, we get:

[tex]U = 20 × 10^-9 C × 3.6 × 10^7 V = 0.72 J[/tex]

Therefore, the electric potential energy of a 20 nC charge at this point would be 0.72 joules.

Learn more about energy    here:

https://brainly.com/question/1932868

#SPJ11

The linear speed of a point on the tip of the rotor can be calculated by the product of distance and angular speed. Therefore, the linear speed of a point on the tip of the rotor is 37.5 m/s.

Angular momentum is a physical quantity that describes an object's amount of rotational motion. It is a vector quantity that is determined by the object's moment of inertia (a measure of its resistance to rotational motion) and angular velocity (the rate at which the object rotates around an axis). Angular momentum is defined mathematically as the cross-product of an object's moment of inertia and angular velocity. When no external torque applies on a closed system, angular momentum is conserved, which is known as the law of conservation of angular momentum. Angular momentum is crucial in many branches of physics, including mechanics, quantum mechanics, and astronomy.

To learn more about angular momentum

https://brainly.com/question/15460796

The linear speed of a point on the tip of the rotor can be calculated by the product of distance and angular speed. Therefore, the linear speed of a point on the tip of the rotor is 37.5 m/s.

Angular momentum is a physical quantity that describes an object's amount of rotational motion. It is a vector quantity that is determined by the object's moment of inertia (a measure of its resistance to rotational motion) and angular velocity (the rate at which the object rotates around an axis). Angular momentum is defined mathematically as the cross-product of an object's moment of inertia and angular velocity. When no external torque applies on a closed system, angular momentum is conserved, which is known as the law of conservation of angular momentum. Angular momentum is crucial in many branches of physics, including mechanics, quantum mechanics, and astronomy.

To learn more about angular momentum

https://brainly.com/question/15460796

a. The magnitude of the impulse acting on the golf ball can be found using the formula I = FΔt, where I is the impulse, F is the force, and Δt is the time interval. Plugging in the values given, we get I = (4800 N)(0.003 s) = 14.4 N·s.

b. The change in the golf ball's momentum can be found using the formula Δp = mvf - mvi, where Δp is the change in momentum, m is the mass of the golf ball, vf is the final velocity, and vi is the initial velocity. Since the problem doesn't give any information about the velocities, we can assume that the golf ball is initially at rest (vi = 0).

Therefore, Δp = mvf.

We can find vf using the formula vf = at, where a is the acceleration and t is the time interval.

The acceleration can be found using the formula a = F/m, where F is the force and m is the mass of the golf ball. Plugging in the values given, we get a = (4800 N)/(0.045 kg) = 106667 m/s^2. Plugging this into the formula for vf, we get vf = (106667 m/s^2)(0.003 s) = 320 m/s. Finally, plugging this into the formula for Δp, we get Δp = (0.045 kg)(320 m/s) = 14.4 kg·m/s.

Therefore, the change in the golf ball's momentum is 14.4 kg·m/s.

a. To find the magnitude of the impulse acting on the golf ball, we can use the formula:

Impulse = Average force × Time interval

Impulse = 4800 N × 0.003 s = 14.4 Ns

So, the magnitude of the impulse acting on the golf ball is 14.4 Ns.

b. The change in the golf ball's momentum is equal to the impulse applied.

Therefore, the change in the golf ball's momentum is also 14.4 Ns.

learn more about momentum here: brainly.com/question/22257327

#SPJ11

Answer:

Approximately [tex]24.3\; {\rm m}[/tex].

Explanation:

Under the assumptions, the net force on the block is equal to the horizontal force from the worker.

During the first [tex]4.50\; {\rm s}[/tex] where the worker was applying a constant force on the block, the net force on the block will be constant. Acceleration of the block will be also constant, and SUVAT equations will apply.

Apply the SUVAT equation:

[tex]\displaystyle x &= \left(\frac{u + v}{2}\right)\, t[/tex],

Where:

(In other words, displacement during constant acceleration is equal to average velocity times the duration of the acceleration.)

Rearrange this equation to find [tex]v[/tex]:

[tex]\begin{aligned}u + v = \frac{2\, x}{t}\end{aligned}[/tex].

[tex]\begin{aligned}v &= \frac{2\, x}{t} - u \\ &= \frac{2\, (13.0)}{4.50} - 0 \\ &= \frac{52}{9}\; {\rm m \cdot s^{-1}}\end{aligned}[/tex].

During the next [tex]4.20\; {\rm s}[/tex], the net force on the block will be zero. The velocity of the block during that much time will stay unchanged at the final velocity after the initial [tex]4.50\; {\rm s}[/tex], which is [tex]v = (52/9)\; {\rm m\cdot s^{-1}}[/tex].

Since velocity during this [tex]4.20\; {\rm s}[/tex] is constant, simply multiply that velocity by the duration to find the distance travelled:

[tex]\displaystyle \left(\frac{52}{9}\right)\, (4.20) \approx 24.3\; {\rm m}[/tex].

In other words, the block would have travelled an additional [tex]24.3\; {\rm m}[/tex] during the [tex]4.20\; {\rm s}[/tex].

The acceleration due to gravity on the planet Htrae is twice the acceleration due to gravity on Earth. Since g(Earth) is approximately 9.8 m/s^2, we have:
g(Htrae) = 2 * 9.8 m/s^2 = 19.6 m/s^2

So the answer is D. 20 m/s^2 (rounded to one significant figure).

The weight of an object is given by the formula:

W = m * g,

where W is weight, m is mass, and g is acceleration due to gravity.

Let's use the given information to solve for the acceleration due to gravity on Htrae. We know that:

Weight on Earth = 450 N
Weight on Htrae = 900 N

We also know that the mass of the object is the same on both planets. Therefore, we can set up the following equation:

m * g(Htrae) = 900 N

Solving for g(Htrae), we get:

g(Htrae) = 900 N / m

To find the value of m, we need to use the weight on Earth. We know that:

W(Earth) = m * g(Earth) = 450 N

Solving for m, we get:

m = 450 N / g(Earth)

Substituting this value of m into the equation for g(Htrae), we get:

g(Htrae) = 900 N / (450 N / g(Earth)) = 2 * g(Earth)

Therefore, the acceleration due to gravity on the planet Htrae is twice the acceleration due to gravity on Earth. Since g(Earth) is approximately 9.8 m/s^2, we have:

g(Htrae) = 2 * 9.8 m/s^2 = 19.6 m/s^2

So the answer is D. 20 m/s^2 (rounded to one significant figure).

Visit to know more about Acceleration:-

brainly.com/question/25876659

#SPJ11

This is the differential equation describing the center of mass position of the spring x(t) for an aging undamped spring with a varying spring constant m([tex]\frac{d^{2}x }{dt^{2} }[/tex]  ) = -k0e(-αt)x(t) + mg .

To find the differential equation describing the center of mass position of the spring x(t), we need to use Newton's second law, which states that the net force acting on an object is equal to its mass times its acceleration. In this case, the object is the spring, and its mass is given by m.
The force acting on the spring is the sum of the forces due to the spring's deformation and its gravitational force. The force due to the spring's deformation is proportional to the displacement of the spring from its equilibrium position, and is given by F = -kx(t), where k is the spring constant at time t. The gravitational force is given by Fg = mg, where g is the acceleration due to gravity.
Therefore, the net force acting on the spring is given by:
Fnet = -kx(t) + mg
Using Newton's second law, we can write:
m([tex]\frac{d^{2}x }{dt^{2} }[/tex]) = -kx(t) + mg
Substituting the expression for k(t) given in the question, we get:
m([tex]\frac{d^{2}x }{dt^{2} }[/tex]²) = -k0e(-αt)x(t) + mg.

Learn more about Newton's second law here

https://brainly.com/question/13447525

#SPJ11

The passband gain for the given first-order circuit is 5, and the cutoff frequency is 15,000 rad/s.

To find the passband gain and cutoff frequency of the voltage transfer function T(s) = 5s/(s + 15,000), follow these steps:

1. Passband gain: In a first-order circuit, the passband gain is simply the coefficient of 's' in the numerator, which is 5 in this case.
2. Cutoff frequency: The cutoff frequency is the value of 's' when the denominator is equal to the numerator. In this case, set 5s = s + 15,000, which gives s = 15,000 rad/s as the cutoff frequency.

To plot the Bode gain response using MATLAB, use the following code:

```MATLAB
numerator = [5 0];
denominator = [1 15000];
sys = tff(numerator, denominator);
bode(sys);
```


This code creates a transfer function object 'sys' with the given numerator and denominator coefficients, then uses the 'bode()' function to plot the Bode gain response.

To know more about passband gain click on below link:

https://brainly.com/question/31424377#

#SPJ11