The common mistake users make when creating filters in a Pivot Table with products in Column A and Sum of Total Purchases in Column B, is filtering in Sum of Total Purchases. The correct option is 'a' filtering in the sum of Total Purchases.
It is important to filter based on the values associated with the products or by using Value Filters to get accurate and meaningful insights from the Pivot Table. Instead of filtering by the values associated with the products (Column A), users mistakenly apply filters to the Sum of Total Purchases (Column B), which might not yield the desired results.Therefore, the correct option is 'a'.To learn more about the Pivot Table: https://brainly.com/question/2222360
SPJ11
for a multi degree of freedom system, the third natural frequency is always higher than the fifth natural frequency, true or false?
False. The natural frequencies of a multi degree of freedom system depend on various factors such as the mass distribution and stiffness of the system.
There is no fixed pattern that the higher numbered natural frequencies will always be higher than the lower numbered ones. The natural frequencies are determined by the system's inherent properties and the mode shapes of vibration.for a multi degree of freedom system, the third natural frequency is always higher than the fifth natural frequency.
To learn more about system click the link below:
brainly.com/question/13439576
#SPJ11
the material is a 350 maraging steel of ys 2240 mpa. what is the critical center crack length?
Once you have these values, you can use the formula above to find the critical crack length for the 350 maraging steel.
The critical center crack length of a material depends on various factors, such as the dimensions and loading conditions of the structure. However, based on the given information that the material is a 350 maraging steel with a yield strength of 2240 MPa, it can be assumed that the critical center crack length is relatively small due to the high strength and toughness of the material. A more detailed analysis and testing would be required to determine the exact critical center crack length for a specific structure or application.
Hi! To determine the critical center crack length for a 350 maraging steel with a yield strength (Ys) of 2240 MPa, you'll need to know the applied stress and the fracture toughness (K_IC) of the material. The critical crack length (a) can be calculated using the formula:
a = (K_IC^2) / (π * σ^2)
where σ is the applied stress and K_IC is the fracture toughness. Since the values for applied stress and fracture toughness are not provided, it's not possible to determine the critical center crack length directly.
Learn more about maraging steel here:-
https://brainly.com/question/14468065
#SPJ11
Given the growth rate function T(n) = 4n3 + 3n2 - 2n for an arbitrary algorithm, show that T(n) = O(n3). Show as much work as necessary.
T(n) = O(n3)
To prove that T(n) = O(n3), we need to find positive constants c and n0 such that T(n) ≤ c * n3 for all n ≥ n0. We can start by simplifying T(n) as follows: T(n) = 4n3 + 3n2 - 2n T(n) = n3(4 + 3/n - 2/n2) Since the term inside the parentheses approaches 4 as n gets larger, we can say that for all n ≥ 1, 4 + 3/n - 2/n2 ≤ 5. Therefore, we can choose c = 5 and n0 = 1, so that T(n) ≤ 5n3 for all n ≥ 1. This shows that T(n) = O(n3), as required.
the wavelength of emission of light from gaas can be adjusted by adding al. determine the proportion of al to ga required to emit light at 850 nm.
the proportion of Al to Ga required to emit light at 850 nm in GaAs is 68.6% Al and 31.4% Ga.
The proportion of Al to Ga required to emit light at 850 nm in GaAs can be calculated using the relationship between the bandgap energy and the emitted photon energy. The bandgap energy of GaAs can be modified by adding Al to it, which changes the composition of the semiconductor alloy.
The relationship between the bandgap energy and the emitted photon energy is given by:
Ephoton = hc/λ
For GaAs, the bandgap energy can be expressed as:
Eg = 1.424 + 1.247x,
where Eg is the bandgap energy, x is the mole fraction of Al in the alloy.
To emit ligh at 850 nm, we need to determine the corresponding bandgap energy. Using the above equation with λ = 850 nm, we get:
Ephoton = hc/λ = 2.33 eV
Substituting this value into the equation for the bandgap energy of GaAs, we get:
2.33 eV = 1.424 + 1.247x
x = (2.33 - 1.424)/1.247 = 0.686
Learn more about emit light here:
https://brainly.com/question/3962600
#SPJ11
p12.11 suppose that an npn transistor is operating with the base emitter junction forward biased and the base collector junction reverse biased. fiven b=200 and ib=ua determine the values of ic and ie
To determine the values of ic and ie in this scenario, we need to use the given values of b=200 and ib=ua.
First, we can use the equation ic = b * ib to find the collector current: ic = 200 * ua = 0.2 mA Next, we can use the fact that the base-emitter junction is forward biased to find the emitter current: ie = ic + ib = 0.2 mA + ua = 0.201 mA Therefore, the values of ic and ie in this scenario are 0.2 mA and 0.201 mA, respectively. Hi! I'd be happy to help you with your question. Given an NPN transistor with a forward-biased base-emitter junction and a reverse-biased base-collector junction, the parameters are β (beta) = 200 and I_B (base current) = µA (microamperes). To determine the values of I_C (collector current) and I_E (emitter current), we can use the following relationships1. I_C = β * I_B
2. I_E = I_B + I_C
First, calculate I_C:
I_C = 200 * I_B µA
Next, determine I_E:
I_E = I_B µA + I_C
By substituting the values provided and solving the equations, you can determine the values of I_C and I_E for this NPN transistor.
To learn more about scenario click on the link below:
brainly.com/question/17129508
#SPJ11
To answer your question, let's first understand the terms involved: Transistor: An NPN transistor is a semiconductor device that controls the flow of current between two terminals (collector and emitter) based on the current applied to a third terminal (base).
2. Biased: A transistor is biased when voltage is applied to its terminals to control the flow of current.
In this problem, the base-emitter junction is forward biased and the base-collector junction is reverse biased, indicating the NPN transistor is in active mode. Given the values of B (beta) = 200 and Ib (base current) = µA (microamperes), we can determine Ic (collector current) and Ie (emitter current) using the following formulas:
1. Ic = B * Ib
2. Ie = Ic + Ib
Let's calculate:
1. Ic = 200 * Ib µA
2. Ie = (200 * Ib + Ib) µA = 201 * Ib µA
So, the collector current (Ic) is 200 times the base current, and the emitter current (Ie) is 201 times the base current.
To learn more about Transistor click the link below:
brainly.com/question/11297995
#SPJ11
What are dimensions of acceleration of gravity, density, dynamic viscosity, kinematic viscosity, specific weight, and speed of sound in the FIT system and the MLT system?
the dimensions of the mentioned terms in both the FIT (Force, Length, Time) and MLT (Mass, Length, Time) systems.
1. Acceleration of gravity:
FIT system: L/T² (Length per Time squared)
MLT system: L/T² (Length per Time squared)
2. Density:
FIT system: F/L⁴ (Force per Length to the power of 4)
MLT system: M/L³ (Mass per Length cubed)
3. Dynamic viscosity:
FIT system: F·T/L² (Force times Time per Length squared)
MLT system: M/T·L (Mass per Time and Length)
4. Kinematic viscosity:
FIT system: L²/T (Length squared per Time)
MLT system: L²/T (Length squared per Time)
5. Specific weight:
FIT system: F/L³ (Force per Length cubed)
MLT system: M·L/T²·L² (Mass times Length per Time squared and Length squared)
6. Speed of sound:
FIT system: L/T (Length per Time)
MLT system: L/T (Length per Time)
learn more about MLT system here:
https://brainly.com/question/30481637
#SPJ11
Identify a problem from any organization of your choice and describe how you would use Software Engineering principles to solve it
One problem that many organizations face is managing large amounts of data efficiently and securely.To address this issue, software engineering principles can be used to develop a database management system that automates data entry, processing, and storage.
What is the explanation for the above response?
The first step would be to analyze the organization's data needs and determine the optimal database structure, including data entities, attributes, and relationships. Then, using software engineering principles, a custom database application can be developed, incorporating features such as data validation, encryption, and user access controls.
Next, the system can be tested using software testing techniques to ensure that it meets the organization's requirements and is free from errors or vulnerabilities. Once deployed, the system can be continuously monitored and maintained using software maintenance techniques to ensure that it remains reliable and secure.
By using software engineering principles to develop a database management system, organizations can streamline their data management processes, reduce errors, and enhance security, ultimately improving their overall efficiency and productivity.
Learn more about Software Engineering at:
https://brainly.com/question/30440013?
#SPJ1
What is the worst-case running time for inserting n items into an initially empty hash table, (a) Where collisions are resolved by chaining? (b) Where collisions are resolved by chaining, and each list is stored in sorted order? (c) Where collisions are resolved by linear probing? For each part, justify your answer briefly. If you need to make a reasonable assumption about the problem statement in order to do so, state that assumption explicitly in your answer.
(a) The worst-case running time for inserting n items into an initially empty hash table is O(n).
(b) Inserting n items into a sorted list takes O(n²) time in the worst case.
(c) Inserting n items into a hash table using linear probing takes O(n²) time in the worst case.
What are the worst-case running times for inserting n items?(a) When collisions are resolved by chaining, the worst-case running time for inserting n items into an initially empty hash table is O(n). This is because each item is inserted into a linked list in the hash table, and in the worst case, all n items hash to the same index and are therefore inserted into the same linked list. In this case, inserting each item takes O(1) time, but inserting n items takes O(n) time.
(b) When collisions are resolved by chaining, and each list is stored in sorted order, the worst-case running time for inserting n items into an initially empty hash table is O(n²). This is because in the worst case, all n items hash to the same index and are therefore inserted into the same linked list, which is then sorted. Inserting an item into a sorted list takes O(n) time in the worst case, because we may need to shift all the elements in the list to make room for the new item. Therefore, inserting n items into a sorted list takes O(n²) time in the worst case.
(c) When collisions are resolved by linear probing, the worst-case running time for inserting n items into an initially empty hash table is O(n²). This is because in the worst case, all n items hash to the same index and each successive item needs to be probed linearly to find an empty slot. As a result, we may have to probe all the way to the end of the hash table to find an empty slot for each item, which takes O(n) time in the worst case. Therefore, inserting n items into a hash table using linear probing takes O(n²) time in the worst case.
Learn more about hash table operations
brainly.com/question/29970427
#SPJ11
write a boolean expression that would have value true if the user input is bigger than -1 note, provide only the boolean expression as your answer.
The boolean expression that would have value true if the user input is bigger than -1 is: (user_input > -1).
The given boolean expression checks whether the user input is greater than -1 or not. If the user input is greater than -1, the expression will evaluate to True, indicating that the condition is satisfied. If the user input is less than or equal to -1, the expression will evaluate to False, indicating that the condition is not satisfied. In other words, this expression can be used to filter out input values that are less than or equal to -1 and only accept input values that are greater than -1.
Learn more about boolean expression here https://brainly.com/question/13265286
#SPJ11
How many different methods can item2 call? class Product: def __init__(self): self.name = 'None self. quantity = 0def set_item(self, nm, aty): self.nane - nm self. quantity = qty ns def get_item(self): return self.name, self.quantity def get_name(self): return self.name АТЕ def get_quantity(self): return self.quantity class Medicine (Product): def __init__(self): Product __init__(self) self.expiration - 2000 def set_expiration(self, exp): self.expiration - exp def get_medicine(self): return self.none, self.quantity, self.expiration item1 = Product()item2 = Medicine()a. 6b. 2c. 8d. 4
the correct answer is 6 methods. Note that there are actually 7 methods listed, but the "__init__" method is called automatically during object instantiation and doesn't need to be explicitly called. Therefore, the correct answer is still 6 methods that can be explicitly called.
item2 can call 6 different methods. Since it is an instance of the Medicine class, which is a subclass of the Product class, it can call all methods defined in both classes. These methods include:
1. __init__(self)
2. set_item(self, nm, aty)
3. get_item(self)
4. get_name(self)
5. get_quantity(self)
6. set_expiration(self, exp)
7. get_medicine(self)
The __init__ method is the Python equivalent of the C++ constructor in an object-oriented approach. The __init__ function is called every time an object is created from a class. The __init__ method lets the class initialize the object's attributes and serves no other purpose. It is only used within classes.
learn more about "__init__" method here:
https://brainly.com/question/30019258
#SPJ11
the correct answer is 6 methods. Note that there are actually 7 methods listed, but the "__init__" method is called automatically during object instantiation and doesn't need to be explicitly called. Therefore, the correct answer is still 6 methods that can be explicitly called.
item2 can call 6 different methods. Since it is an instance of the Medicine class, which is a subclass of the Product class, it can call all methods defined in both classes. These methods include:
1. __init__(self)
2. set_item(self, nm, aty)
3. get_item(self)
4. get_name(self)
5. get_quantity(self)
6. set_expiration(self, exp)
7. get_medicine(self)
The __init__ method is the Python equivalent of the C++ constructor in an object-oriented approach. The __init__ function is called every time an object is created from a class. The __init__ method lets the class initialize the object's attributes and serves no other purpose. It is only used within classes.
learn more about "__init__" method here:
https://brainly.com/question/30019258
#SPJ11
Is this a example of a v6 or a v8?
The main difference between a V6 engine and a V8 engine is the total cylinders in the engine for fuel intake.
What is the engine about?A V6 engine has six cylinders, whereas a V8 engine has eight. V6 engines typically consume less fuel than V8 engines, whereas V8 engines provide greater power than V6 engines.
When compared to a V6 engine, V8 engines typically provide more energy and peak performance. This is due to the fact that a V8 has eight cylinders as opposed to a V6, which only has six, allowing for more gasoline and air to be used while ultimately producing more strength.
Learn more about engine on
https://brainly.com/question/25870707
#SPJ1
answer the following for the analytical engine: how many numbers can be stored?
A simply supported 25 foot long steel beam is loaded uniformly with a dead load of 150 kips per foot and a live load of 400 kipa per foot. There is adequate to support provided to the beam. Assume the design beam will be a W21 shape using grade 50 steel. What is me requred section modules in . a. 575 b. 171 c. 499 d. 641
The correct answer is (c) 499.We can use a steel beam design manual or a structural steel shape database to find the section modulus for a W21 shape using grade 50 steel. The section modulus for a W21x57 shape (closest to W21) is 171 [tex]in^3[/tex].
To determine the required section modulus for the beam, we can use the following steps:
Step 1: Calculate the total load on the beam.
Total load = Dead load + Live load
Total load = 150 kips/ft + 400 kips/ft = 550 kips/ft
Step 2: Calculate the maximum bending moment on the beam.
Maximum bending moment = (Total load x [tex]Length^2)/8[/tex]
Maximum bending moment = (550 kips/ft x ([tex]25 ft)^2)/8[/tex] = 5,734 kip-ft
Step 3: Determine the required section modulus for the beam.
Required section modulus = Maximum bending moment / Allowable stress
We can use the allowable stress for grade 50 steel, which is 24 ksi.
Required section modulus = 5,734 kip-ft / 24 ksi = 239 [tex]in^3[/tex]
Step 4: Calculate the section modulus for a W21 shape using grade 50 steel.
Learn more about section modulus here:
https://brainly.com/question/23818966?referrer=searchResults
#SPJ11
a helical gear pair is to be a part of the drive for a milling machine requiring 20 hp with the pinion speed at 550 rpm adn the gear speed to be between 180 and 190 rpm
A helical gear pair with a gear ratio of 0.33:1 can be used as part of the drive for the milling machine. when a helical gear pair is to be a part of the drive for a milling machine requiring 20 hp with the pinion speed at 550 rpm adn the gear speed to be between 180 and 190 rpm
To create a drive for a milling machine requiring 20 hp with a pinion speed of 550 rpm and a gear speed between 180 and 190 rpm, a helical gear pair can be used. A helical gear pair consists of two gears with helical teeth that mesh together at an angle.
To determine the appropriate gear ratio, we can use the following formula:
Gear Ratio = Gear Speed / Pinion Speed
We can rearrange this formula to solve for the gear speed:
Gear Speed = Gear Ratio x Pinion Speed
In this case, we want the gear speed to be between 180 and 190 rpm. Let's choose a gear ratio of 0.33:1.
Gear Speed = 0.33 x 550 = 181.5 rpm
This falls within the desired range of 180-190 rpm.
In milling machine, a helical gear pair is used as part of the drive system to transmit 20 hp of power. The pinion, which is the smaller gear in the pair, has a speed of 550 rpm, while the larger gear's speed is set to be between 180 and 190 rpm. This arrangement ensures efficient power transmission and smooth operation of the milling machine.
To learn more about Helical gear Here:
https://brainly.com/question/21730765
#SPJ11
Given the following memory map of the display screen:
If we want to change the bit in row 10, column 50 of the Screen, what address should we retrieve and which bit should be changed?
Screen memory
map
Display Unit (256 by 512, b/w)
0 1 2 3 4 5 6 7 ..
Screen
(16384) 0 1111010100000000
1 0000000000000000
511
Group of answer choices
Screen[10], 50th bit
Screen[16], 3rd bit
Screen[3], 16th bit
Screen[323], 3rd bit
Screen[3], 323th bit
Screen[324], 3rd bit
Screen[3], 324th bit
To change the bit in row 10, column 50 of the Screen, we need to retrieve the address Screen[323] and change the 3rd bit.
In computer science, a memory map is a structure of data (which usually resides in memory itself) that indicates how memory is laid out. The term "memory map" can have different meanings in different contexts.
It is the fastest and most flexible cache organization that uses an associative memory. The associative memory stores both the address and content of the memory word.[further explanation needed]
In the boot process, a memory map is passed on from the firmware in order to instruct an operating system kernel about memory layout. It contains the information regarding the size of total memory, any reserved regions and may also provide other details specific to the architecture.
In virtual memory implementations and memory management units, a memory map refers to page tables or hardware registers, which store the mapping between a certain process's virtual memory layout and how that space relates to physical memory addresses.
To learn more about Bit Here:
https://brainly.com/question/16005809
#SPJ11
what is an infinite loop? on your computer, how can you terminate a program that executes an infinite loop?
An infinite loop is a programming construct where a set of instructions repeatedly executes, and the loop does not stop until an external factor or a specific command is given.
An infinite loop can be intentional, where the programmer intends the loop to run forever, or unintentional, where a programming error causes the loop to continue running without end.To terminate a program that executes an infinite loop on your computer, you can use a keyboard shortcut to force quit the program. On Windows, you can use the "Ctrl + Alt + Del" keys to bring up the Task Manager, which allows you to end the program manually. On a Mac, you can use the "Command + Option + Esc" keys to bring up the Force Quit Applications window, which lets you select and end the program that is stuck in an infinite loop. Alternatively, you can also use command line tools to stop the program's process manually.https://brainly.com/question/13142062
#SPJ11
what relationship best allows you to tell the relative ages between the schist and the conglomerate? a. cross-cutting relationshipb. principle of inclusionc. principle of stratigraphic superpositiond. principle of original continuitye. principle of original horizontality
The relationship that best allows you to determine the relative ages between the schist and the conglomerate is the principle of stratigraphic superposition (option c). This principle states that in an undisturbed sequence of sedimentary rocks, the oldest layers are at the bottom and the youngest layers are at the top. By examining the position of the schist and the conglomerate in the rock sequence, you can determine their relative ages.
The relationship that best allows you to tell the relative ages between the schist and the conglomerate is the principle of stratigraphic superposition. This principle states that in an undisturbed sequence of sedimentary rocks, the oldest layers are at the bottom and the youngest layers are at the top. Therefore, if the schist is found below the conglomerate, it is older, and if it is found above the conglomerate, it is younger. The other principles listed (cross-cutting relationship, principle of inclusion, principle of original continuity, principle of original horizontality) can help determine relative ages in different situations, but in this case, the principle of stratigraphic superposition is the most applicable.
Learn more about stratigraphic superpositionhere:-
https://brainly.com/question/29455696
#SPJ11
The Pratt bridge truss supports five equal loads, F = 300 KN. If the dimension L = 8 m use the method of joints to determine the axial forces in members BC, BI, and BJ. [-1200 kN. 636 kN. 300 kN]
The axial forces in members BC, BI, and BJ are -1200 kN, 636 kN, and 300 kN, respectively.
How to determine the axial forces in members BC, BI, and BJ using the method of joints?To determine the axial forces in members BC, BI, and BJ using the method of joints, we need to follow these steps:
Step 1: Draw the free-body diagram of the entire truss and apply the equations of static equilibrium to determine the reactions at the supports. Since the truss is symmetrical, the reactions at the supports are equal and opposite and have a magnitude of 750 kN.
Step 2: Identify the joints in the truss and assign them unique labels. There are 5 joints in the Pratt truss, labeled A, B, C, I, and J.
Step 3: Draw a free-body diagram of each joint and label the forces acting on each joint. The forces acting on each joint are the external load (F = 300 kN), the axial forces in the truss members, and the reaction forces at the supports.
Step 4: Apply the equations of static equilibrium to each joint. Since we have three unknown axial forces in each joint, we need to write three equilibrium equations for each joint.
For joint B, we have:
ΣF_x = 0: -BC - BI = 0
ΣF_y = 0: -F + BJ + 2750 = 0
ΣF_z = 0: BCcos(45) - BJ*cos(45) = 0
Solving these equations, we get:
BC = -1200 kN
BI = 636 kN
BJ = 300 kN
Therefore, the axial forces in members BC, BI, and BJ are -1200 kN, 636 kN, and 300 kN, respectively.
Learn more about axial forces
brainly.com/question/31060177
#SPJ11
The process ID is guaranteed to be unique and will not be reused until the Operating System is rebooted True or False
True. The process ID is a unique numerical identifier assigned by the Operating System to each process running on the system.
The Operating System ensures that each process is assigned a unique process ID, and that no two processes have the same process ID at the same time. Once a process ID is assigned to a process, it will not be reused until the Operating System is rebooted. This ensures that each process can be uniquely identified and managed by the Operating System, without any conflicts or issues.
The PID remains unique throughout the life of the process. Once a process is terminated, its PID can be reused by the Operating System for new processes. However, the PID is not reused until the Operating System has been rebooted. This ensures that each process has a unique identifier during a single session, allowing for effective process management and resource allocation.
To learn more about operating system : brainly.com/question/24760752
#SPJ11
1) display all invoices with balance due $200 or more (after payments and credits). return invoice number, date of invoice, and amount due. sort by the balance due amount in descending order.
You will display all the required invoices with a balance due of $200 or more, showing the invoice number, date of invoice, and amount due, sorted by the balance due amount in descending order.
Display all invoices with balance due $200 or more?To display all invoices with a balance due of $200 or more (after payments and credits), perform the following:
First, identify the relevant data fields you need to access, which are: invoice number, date of invoice, amount due, payments, and credits.
Filter the invoices based on the condition: (amount due - payments - credits) >= $200.
Retrieve the desired fields for the filtered invoices: invoice number, date of invoice, and the calculated amount due (amount due - payments - credits).
Sort the resulting invoices by the calculated balance due amount in descending order.
By following these, you will display all the required invoices with a balance due of $200 or more, showing the invoice number, date of invoice, and amount due, sorted by the balance due amount in descending order.
Learn more about descending order.
brainly.com/question/23938305
#SPJ11
What will happen to the entropy of a flow across a shock? A. Stays the same B. Decrease C. Increase
The entropy of a flow across a shock will increase.
This is because the shock creates a sudden change in the flow variables such as pressure, temperature, and velocity, leading to an increase in disorder or randomness of the flow. This increase in entropy is a consequence of the irreversible nature of shocks, where a large amount of energy is dissipated in the form of heat due to the sudden change in flow conditions. The isentropic relations then provide the change in flow attributes. "Constant entropy" is what "isentropic" means. However, the flow process becomes irreversible and the entropy rises when an object travels faster than the speed of sound and the flow area suddenly decreases. There are shock waves produced.
Learn more about temperature here-
https://brainly.com/question/11464844
#SPJ11
With two values of the rate constant, the activation energy can be found using the following form of the Arrhenius equation: In k1/k2=-Ea/R(1/T1-1/T2)The rate constant for the conversion of cyclopropane to propene is 1.10 x 10+5+ at 470 °C and 1.02 x 10-3 3-4 at 510 °C. What is the activation energy? ()
The activation energy for the conversion of cyclopropane to propene is approximately 193,830 J/mol.
To find the activation energy (Ea) using the given values and the Arrhenius equation, we'll first need to convert the temperatures from Celsius to Kelvin:
T1 = 470 °C + 273.15 = 743.15 K
T2 = 510 °C + 273.15 = 783.15 K
The rate constants (k1 and k2) are given as:
k1 = 1.10 x 10^5 at T1
k2 = 1.02 x 10^-3 at T2
Now, we'll use the Arrhenius equation to find Ea:
ln(k1/k2) = -Ea/R(1/T1 - 1/T2)
Where R is the gas constant, 8.314 J/(mol K).
Plugging in the values:
ln(1.10 x 10^5 / 1.02 x 10^-3) = -Ea / 8.314 (1/743.15 - 1/783.15)
Now, solve for Ea:
Ea = -8.314 * ln(1.10 x 10^5 / 1.02 x 10^-3) / (1/743.15 - 1/783.15)
Ea ≈ 193,830 J/mol
Learn More about activation energy here :-
https://brainly.com/question/28384644
#SPJ11
Block B (1 kg) is moving on the smooth surface at 10 m/s when it squarely strikes block A (3 kg), which is at rest. If the velocity of block A after the collision is 4 m/s to the right, (vB)2 is
Block B (1 kg) is moving on the smooth surface at 10 m/s when it squarely strikes block A (3 kg), which is at rest. If the velocity of block A after the collision is 4 m/s to the right, the velocity of block B after the collision is -2 m/s to the left.
To solve this problem, we can use the conservation of momentum principle, which states that the total momentum of the system before the collision is equal to the total momentum of the system after the collision.
Let's denote the initial velocity of block B as vB1 and the final velocity of block B as vB2. We can set up the equation as follows:
mBvB1 + mA*vA1 = mBvB2 + mA*vA2
where mB and mA are the masses of block B and block A, respectively, and vA1 is the initial velocity of block A, which is zero.
Plugging in the given values, we get:
1 kg * 10 m/s + 3 kg * 0 = 1 kg * vB2 + 3 kg * 4 m/s
Simplifying the equation, we get:
10 kg m/s = vB2 + 12 kg m/s
Subtracting 12 kg m/s from both sides, we get:
vB2 = -2 kg m/s
Learn more about velocity here: https://brainly.com/question/25905661
#SPJ11
Use the Routh-Hurwitz criterion to find how many poles of the following closed-loop system, represented by the transfer function T(s), are in the RHP, in the LHP, and on the imaginary (jω) axis: T(s)=s6+s5−6s4+0s3−s2−s+6s3+7s2−21s+10
To apply the Routh-Hurwitz criterion to the given transfer function T(s), we first need to construct the Routh array:
s^6: 1 -6 6
s^5: 1 -1 -21
s^4: 6 10 0
s^3: 7 -21 0
s^2: 30 0 0
s^1: -21 0 0
s^0: 10 0 0
The first column of the Routh-Hurwitz array contains the coefficients of the even powers of s, while the second column contains the coefficients of the odd powers of s. If any element in the first column is zero, we replace it with a small epsilon value to avoid division by zero.
To determine the number of poles in the RHP, we count the number of sign changes in the first column of the Routh array. In this case, there are no sign changes, which means that all the poles are either in the LHP or on the imaginary axis.
To determine the number of poles on the imaginary axis, we count the number of sign changes in the first column of the Routh array after replacing any zero elements with epsilon. In this case, there is one sign change, which means that there is one pole on the imaginary axis.
To determine the number of poles in the LHP, we count the number of rows in the Routh array that have all positive elements. In this case, there are four such rows, which means that there are four poles in the LHP.
Therefore, the number of poles in the RHP is zero, the number of poles on the imaginary axis is one, and the number of poles in the LHP is four.
Learn more about Routh-Hurwitz: https://brainly.com/question/14947016
#SPJ11
Property taxes on a manufacturing plant are an element of a Prosdact Cost Periad Cost
A) Yes No
B) No Yes
C) No No
D) Yes Yes
Property taxes on a manufacturing plant are an element of a Product Cost Period Cost. The correct answer is:
B) No Yes
Property tax is a tax paid on property owned by an individual or other legal entity, such as a corporation. Most commonly, property tax is a real estate ad-valorem tax, which can be considered a regressive tax. It is calculated by a local government where the property is located and paid by the owner of the property. The tax is usually based on the value of the owned property, including land. However, many jurisdictions also tax tangible personal property, such as cars and boats.
The local governing body will use the assessed taxes to fund water and sewer improvements, and provide law enforcement, fire protection, education, road and highway construction, libraries, and other services that benefit the community. Deeds of reconveyance do not interact with property taxes.
learn more about Product Cost Period Cost here:
https://brainly.com/question/29590425
#SPJ11
if the 0.100 mm diameter tungsten filament in a light bulb is to have a resistance of 0.150 ω at 20.0°c, how long (in m) should it be?
The tungsten filament should be approximately 210.94 meters long.
How to determine the length of the tungsten filament?To determine the length of the tungsten filament, we can use the formula for the resistance of a wire:
R = ρ * (L / A),
where R is the resistance of the wire, ρ is the resistivity of the material, L is the length of the wire, and A is the cross-sectional area of the wire.
First, we need to find the resistivity of tungsten at 20°C. According to a reference source, the resistivity of tungsten at 20°C is 5.6 x 10^-8 Ωm.
The cross-sectional area of the filament can be found using the formula for the area of a circle:
A = π * (d/2)^2,
where d is the diameter of the filament. Substituting the given values, we get:
A = π * (0.100/2)^2 = 7.85 x 10^-6 m^2.
Now we can rearrange the formula for resistance to solve for L:
L = R * A / ρ.
Substituting the given values, we get:
L = (0.150 Ω) * (7.85 x 10^-6 m^2) / (5.6 x 10^-8 Ωm) = 210.94 m.
Therefore, the tungsten filament should be approximately 210.94 meters long.
Learn more about electrical resistance
brainly.com/question/29604143
#SPJ11
consider the following mips instruction. what would the corresponding machine code be? write your answer in binary
To provide an accurate answer, I need the specific MIPS instruction you're referring to. Please provide the instruction, and I'll be happy to help you find the corresponding machine code in binary.
To provide the corresponding machine code for a given MIPS instruction, we need to know the format of the instruction. The MIPS instruction format is divided into three types: R-type, I-type, and J-type.
For example, let's consider the following MIPS instruction:
add $t0, $t1, $t2
This instruction is an R-type instruction since it operates on registers. The opcode for the add instruction is 000000, and the function code is 100000. The three registers used in this instruction are $t0, $t1, and $t2, which have register numbers 8, 9, and 10, respectively.
Using this information, we can write the corresponding machine code in binary as follows:
opcode (6 bits) | rs (5 bits) | rt (5 bits) | rd (5 bits) | shamt (5 bits) | funct (6 bits)
000000 | 01001 | 01010 | 01000 | 00000 | 100000
Therefore, the machine code for the given MIPS instruction add $t0, $t1, $t2 is 00000001001010100100000000100000 in binary.
learn more about MIPS instruction here:
https://brainly.com/question/30543677
#SPJ11
Show that the strain energy in a bar of length L and cross sectional area A hanging from a ceiling and subjected to its own weight is given by (at any section, the force acting is the weight of the material below that section)U = Ap^2g^2L^3 / 6E
The strain energy in a bar of length L and cross-sectional area A hanging from a ceiling and subjected to its own weight is given by U = Ap^2g^2L^3 / 6E, where p is the density of the material, g is the acceleration due to gravity, and E is the modulus of elasticity.
The strain energy in a bar hanging from a ceiling and subjected to its own weight can be calculated using the formula U = Ap^2g^2L^3 / 6E, where A is the cross-sectional area, p is the density of the material, g is the acceleration due to gravity, L is the length of the bar, and E is the modulus of elasticity. This formula assumes that the force acting at any section is the weight of the material below that section. Strain energy is the energy stored in a material when it is deformed under load. When a bar is hanging from a ceiling, it is subjected to its own weight, which causes it to deform. The formula U = Ap^2g^2L^3 / 6E allows us to calculate the strain energy in the bar due to its weight. This information is important for designing structures that can support the weight of the bar without failing due to excessive deformation.
For more questions like Elasticity click the link below: https://brainly.com/question/28790459 #SPJ11
test equipment for checking the primary circuit is being discussed. technician a says a logic probe can be used. technician b says a dmm can be used. who is correct?
Technician A is correct. Technician B is also correct that a Digital Multimeter (DMM) can be used, as it measures various electrical values like voltage, current, and resistance.
Both technicians are partially correct.
A logic probe can be used to test the primary circuit as it can detect and indicate the presence of logic signals, such as pulses or high/low voltages.
A DMM (digital multimeter) can also be used to test the primary circuit as it can measure voltage, current, and resistance. However, it may not be able to detect the presence of logic signals.
Therefore, it depends on the specific needs and requirements of the testing situation. If logic signals need to be detected, a logic probe would be more appropriate. If voltage, current, and resistance measurements are needed, a DMM would be more appropriate.
To learn more about Digital Multimeter, click here:
brainly.com/question/5135212
#SPJ11
4.19 an industrial wastewater has a 5-day bod of 370 mg/l and a 10-day bod of 500 mg/l. if the bod progression follows first-order kinetics, determine the ultimate bod.
The ultimate BOD (Lo) is given as 570.41 mg/L
How to solve
we know that BOD(t)=Lo (1-(e^-kt)) where t=time, Lo= ultimate BOD, k= temperature constant(time^-1).
Given BOD(5)=370mg/L
BOD(10)=500 mg/L
assume temperature was same during total procedure so kwill be constant.
so we can write
370=Lo(1-(e^-k * 5)) -----> (1)
and 500=Lo(1-(e- k* 10)) ------>(2)
by dividing equation (1) by equation (2)
[tex]\frac{1-e^{-5k}}{1-e^{-10k}}= 370/500[/tex] by solving
[tex]37 e^{-10k}-50e^{-5k}+13=0[/tex]
assume e^{-5k}=t
so equation will become
[tex]37 t^2 - 50 t +13 =0[/tex]
by solving we get t=1 or .3514
if t=1 then k=0 k can not be zero so
t=.3514 then k=.2092 day ^ -1
so the calculation of ultimate BOD (Lo)
370=Lo(1-e(-5 * .2092))
Lo=370/.6487=570.41 mg/L
Read more about industrial wastewater here:
https://brainly.com/question/30939874
#SPJ1